Industries / Industrial equipment and services / Industrial services
Pump and valve repair
Pump and valve repair is the trade of finding out what is wrong with the pumps, valves and shaft seals of plants such as refineries, power stations, chemical works and water utilities, taking them apart, restoring or replacing their worn parts, and testing them before they go back into service.
1850
Henry R. Worthington replaced the flap valves of his direct-acting steam pump, patented the year before, with many small valves of India rubber disks riding on brass spindles, a design that ASME's landmark brochure says reduced leakage and damage by debris and enabled simple replacement.
39
Milestones achieved across 7 domains.
8
To watch for: announced, not yet confirmed outside.
15
Open deliverables. Nobody has shipped them.
In one minute
Where it started
Plant pumps were built to be repaired from early on: Henry R. Worthington's steam pumps of the 1850s had many small rubber valves that could be swapped when worn, and a plunger packing ring that could be replaced when gritty water damaged it. In 1925 George J. Cooke patented a seal in which a spring presses two flat faces together, the layout of today's end-face mechanical seals. Independent repair shops grew up beside the makers' own service centers; Hydro, which says it became the world's largest independent pump rebuilder, opened its first service center in Chicago in 1969.
Where it stands
Repair and spare parts are now a large share of the pump business: Flowserve, a US maker, reports that aftermarket parts and services were about 53% of its $4.73 billion in sales in 2025, served from 152 of what it calls Quick Response Centers, and the Services division of Sulzer, which repairs and overhauls pumps, compressors, turbines and generators, had sales of CHF 1.31 billion. Much of the trade's practice was written after failures and audits: nuclear plants were told to test motor-operated valves against full pressure after two valves would not reopen at Davis-Besse in 1985, US rules from 1983 made chemical plants survey their pumps and valves for leaks, and refinery engineers' comparisons of how their pump seals performed led to a pump seal standard, API 682, in 1994. Diagnosis by vibration, sound and motor current is routine, and printed metal impellers have been certified and fitted at a few plants, while most utility seal shops still read seal face flatness by eye and work orders record findings in short free text that is hard to compare.
What is open
Little of what repair shops learn is published: no public data pairs a diagnosis made before a pump was removed with what was found inside, shows how fast wear ring clearances open in service, or says how long printed impellers last. Most of the open jobs here are records, prototypes and bench tests that need no live equipment, such as a coded set of real pump work orders for scoring AI models, a phone app that reads a seal face's flatness, a camera that counts the bubbles in a valve seat test, a robot that repacks a valve on the bench, and a printable guide to which plug valve bolts hold pressure.
Domains
AchievedWatch forOpen
Domain
Progress
Last achieved
Watch for
Open
Diagnosis
Diagnosis is the work of finding out what is wrong with a pump or valve while it is still installed, from its vibration, its sound, the current its motor draws or the way it moves, before anyone opens it.
6 · 2 · 3
Last achievedA contest to hear faults2020
Watch forCurrent watches sewage pumps
3
openTeardown and inspection
Teardown and inspection is the shop work of taking a pump or valve apart, cleaning it, measuring the wear on its parts and reading the damage, to decide what to repair and to find out why it failed.
4 · 0 · 2
Last achievedFaces flat until installed2024
2
openMachining and parts
Machining and parts is the work of restoring worn parts and making new ones: welding hard alloys onto valve seats, copying parts whose maker has gone, and casting, printing or machining replacements.
6 · 1 · 2
Last achievedA refinery qualifies printed parts2022
Watch forPrinted impellers for offshore pumps
2
openSeals and bearings
Seals and bearings work is replacing and rebuilding the parts that stop a pump or valve leaking where a turning shaft or a moving stem passes out through its casing, and the bearings that carry the shaft.
5 · 1 · 2
Last achievedBearing life counts dirt2007
Watch forSeals for ethane pipelines
2
openTesting
Testing is how a shop or plant proves that a repaired pump or valve works and does not leak: performance runs that measure flow, pressure and power, pressure tests of valve bodies, seats and packing, set-pressure checks of relief valves, and the leak surveys that plants make in service.
6 · 1 · 2
Last achievedGas cameras get rules2024
Watch forRobots look for gas leaks
2
openField service
Field service is repair work done where a pump or valve is installed, often while the rest of the plant keeps running: sealing leaks under pressure, lining up a pump with its motor, and taking off or refitting the actuator or gearbox that turns a valve.
6 · 1 · 2
Last achievedPlug valve bolts get labels2025
Watch forA guide for existing valves
2
openRepair records
Repair records say who is allowed to repair a pump or valve, what was found and done each time, and how often each kind of equipment fails, so that plants can compare their results and judge whether their maintenance works.
6 · 2 · 2
Last achievedPump failures trended nationwide2026
Watch forWork orders from voice
2
open
Advances to build with
4 research notes

Claude Fable 5.2
Three working devices
Anthropic says its AI model Claude Fable 5.2 designed three prototype devices that worked without electrical modifications, with no outside test reported.

NVIDIA GR00T 2
Five demonstrations per task
By NVIDIA's own test, its robot model GR00T 2 averages 95% success after five demonstrations of a task, on 50 tasks picked from those it learns that way.

Mistral Large 4
A trillion open parameters
Mistral published its Large 4 AI model, a trillion numbers by its count, free to download and sell, though firms that rent out models need a separate license.

Inkling 2 Small
Checked without being asked
The maker of Inkling 2 Small, Thinking Machines, says the AI model checks its work without being asked, a habit that no published test measures.
Open in pump and valve repair
3 of 15 open deliverables
Open · Diagnosis
Check the call at teardown
A public table that pairs what was diagnosed before a pump or control valve was removed (the vibration report, motor current reading or valve test, with the fault named and its severity) with what the repair shop found when it opened the machine, and scores how often the call was right.
Built with what exists
Anonymized diagnosis reports, work orders and teardown inspection sheets with photos from cooperating plants and repair shops; a model that answers the same fixed questions about each report, such as Gemini Decision 1 (see the Note "A thousand questions, one pass"); DuckDB or a spreadsheet; a second person to check the coding.
Open · Teardown and inspection
Name the damage on parts
A public, labeled photo set of worn pump and valve parts taken on the teardown bench, such as impellers, wear rings, shaft sleeves, valve discs and seats, each labeled by experienced repairers with the damage it shows: cavitation (pitting from vapor bubbles that collapse against the metal), erosion by solids, corrosion, rubbing or fatigue cracks. Add a baseline image model scored on parts it has not seen.
Built with what exists
A phone or mirrorless camera with a light box and turntable; CVAT, an open labeling tool; Meta's Segment Anything Model 2 to speed outlining; an Ultralytics YOLO11 classification or segmentation model as the baseline.
Open · Machining and parts
Rebuild worn vanes from scans
Software that takes a 3D scan of a worn or broken impeller, fits the surfaces of the parts that are still whole, and rebuilds the missing vane tips, edges and shroud into a CAD model a shop can machine or print from, with a map of every place it had to guess.
Built with what exists
A structured-light scanner, such as a Revopoint or Creality model, or a measuring arm; Open3D to align scans and compare surfaces; CadQuery to build the CAD model from code, using the fact that the vanes repeat around the axis; a coding agent that checks its own work, such as Inkling 2 Small (see the Note "Checked without being asked").
Where it sits
Broader