BRENNEN

Industries / Technology / Telecommunications

Networking equipment

Networking equipment is the industry that designs and makes the routers, switches, Wi-Fi access points, plug-in optical modules and firewalls that carry data between computers, and the software that runs them.

1969

On the last Saturday of August 1969 the first Interface Message Processor (IMP), a packet switch that BBN built on a Honeywell DDP-516 minicomputer for the ARPANET, arrived at UCLA and was passing data the same day; the Computer History Museum says IMPs "evolve into today's routers.".

computerhistory.orghistoryofcomputercommunications.info

37

Milestones achieved across 6 domains.

10

To watch for: announced, not yet confirmed outside.

12

Open deliverables. Nobody has shipped them.

In one minute

Where it started

The first routers were the IMPs that BBN built for the ARPANET in 1969, and Cisco began selling routers that joined networks of different kinds in 1986. Switches replaced shared Ethernet cables in the early 1990s, Juniper moved packet forwarding into custom chips in 1998, and Wi-Fi became a mass product after Apple sold a $99 wireless card in 1999.

Where it stands

IDC, a market research firm, counted $18.9 billion of Ethernet switch sales and $4.5 billion of router sales worldwide in the second quarter of 2026, up 43.4% and 22.8% on a year earlier. Networks for AI data centers drive most of the growth: switches for data centers made up $12.3 billion of that quarter, NVIDIA led that segment, and Cisco led switches overall and routers, with Huawei close behind in routers. In security, attackers have taken over VPN gateways and hundreds of thousands of home routers, and US and EU rules now reach the devices themselves.

What is open

Much of what this gear does is recorded only by its makers: how many routes a router can hold, how much power a module draws, which modules a switch will accept, and whether a router gets the security updates its maker promised. The open deliverables here are public tables and bench tests built on second-hand equipment and open tools such as Batfish, SONiC, GoBGP and FACT. AI models make some of them practical for a small team, such as translating router configurations between makers and reading firmware at scale, with every result checked by a machine or a person.

Domains

AchievedWatch forOpen

Advances to build with

2 research notes

Open in networking equipment

3 of 12 open deliverables

Open · Routers and switches

A route-capacity table, tested

A public table of how many IPv4 and IPv6 routes each router and switch model can hold in its forwarding hardware, under each memory profile it offers, with the year each one fills up on Huston's projections. Alongside it, a bench test of five second-hand models: load a real full routing table, count how many routes each actually installs, and record what it does past the limit, such as an alarm, a crash or silently missing routes.

Built with what exists

Vendors' datasheets and configuration guides; full-table dumps from RIPE NCC's Routing Information Service, published in MRT format (about 425 MB for one collector's daily table); GoBGP, whose gobgp mrt inject command loads such a dump into a BGP session; used routers on a bench cut off from any live network; an AI model to pull figures out of PDFs, quoting the sentence each came from, with every figure checked by hand.

Credit · unclaimed

Open · Wi-Fi

Multi-link Wi-Fi in flats

A public field study of Wi-Fi 7 multi-link operation in apartment buildings, where dozens of neighbouring networks crowd the same channels. In each flat, with the residents' consent and on networks they own, run the same throughput and latency tests with MLO on and off, on access points from at least three makers, and publish every raw log.

Built with what exists

Wi-Fi 7 access points with MLO from three makers; laptops with Intel BE200 Wi-Fi 7 cards; iperf3 for throughput and Flent for latency under load; a second laptop logging how busy each channel is; Zenodo for a citable data release.

Credit · unclaimed

Open · Plug-in optics

Watts per module, measured

A public table of the power that plug-in optical modules actually draw, measured the same way across many makers and types: SFP+, SFP28 and QSFP28 modules at 10 to 100 Gbit/s, and 400G and 800G modules, both LPO and DSP-based where a tested switch supports them, each idle and at full traffic, at two or more inlet air temperatures.

Built with what exists

Second-hand switches whose software reports power, such as the Cisco Nexus 93600CD-GX, Cisco Catalyst 9500 and Juniper QFX5120 that Flexoptix used; a plug-in power meter on each switch's supply cord to check the switch's own figures; the modules' diagnostic readings (CMIS VDM pages) read through the switch command line; Class 1 (eye-safe) modules looped back with patch cords, never a live network; Zenodo for a citable release.

Credit · unclaimed

Where it sits