Industries / Construction and property / Commercial and residential construction / Modular and prefab building
Factory production
Factory production is the work of building wall panels, roof trusses or whole room-sized boxes, called modules, on a production line indoors, ready to ship to the site.
6
Milestones achieved, from 1945 to 2020.
2
To watch for: announced, not yet confirmed outside.
2
Open deliverables. Nobody has shipped them.
The road
AchievedWatch forOpen
Achieved
1945
Aircraft plants make houses
Britain's Housing (Temporary Accommodation) Act of 1944 set up a program of factory-made temporary homes, and 156,623 prefabricated bungalows were built from 1945 to 1949, by Historic England's count. One type, the aluminum AIROH house, was made by aircraft firms that needed new work after the war and came in four sections, each delivered by truck. The first prefab in the country to be put up and lived in was an AIROH built by the Bristol Aeroplane Company, opened at 125 Nibley Road, Bristol, on 18 July 1945, by Bristol Museums' account.
Credit
the Aircraft Industries Research Organisation on Housing (AIROH); the Bristol Aeroplane Company
1952
Roof trusses from a plant
A truss is a triangulated frame that holds up a roof. In 1952 A. Carroll Sanford invented the metal plate-connected wood truss, by Fine Homebuilding's account: light lumber joined by steel plates, made in a plant and lifted into place by the framing crew. Trusses replaced the complicated roof layout that carpenters had cut on site, at a time when skilled carpenters were short after World War II, and his company, Sanford Industries, made them in many shapes and sizes.
Credit
A. Carroll Sanford, Sanford Industries
1969
Operation Breakthrough falls short
The US Department of Housing and Urban Development (HUD) began Operation Breakthrough in May 1969 to prove factory-built housing. It chose 22 housing systems, from precast concrete and wood-framed modules to units made largely of plastic or metal, out of more than 200 entrants, and built more than 2,900 prototype homes at nine sites. Of 25,000 subsidized homes planned for volume production, 18,000 were finished by March 1976. In 1976 the General Accounting Office (GAO) found that the program did not prove most of its methods could sell, because the housing market fell, HUD's subsidized mortgage programs were suspended, and some systems lacked cost savings.
LessonGAO said such programs need market analysis and a plan for selling the product, not only prototypes.
Credit
HUD under Secretary George Romney
1970
A house of steel boxes
Sekisui Chemical's Heim M1 built houses from standard steel-framed boxes 2.4 m by 5.0 m by 2.7 m, fitted in the factory with walls, floors, ceiling panels, faucets and sinks, then joined and stacked on site into a two-story house. More than 100,000 were sold in the first 14 years, by the count of Docomomo Japan, which lists the M1 among its 100 selected modern Japanese buildings.
Credit
the architect Katsuhiko Ohno and Sekisui Chemical
1973
Mobile homes reach scale
US shipments of mobile homes, built whole in factories, rose from 60,000 in 1947 to nearly 600,000 in 1973, and around 1970 they were more than a third of new single-family homes. Their price fell from about $18 to $6 per square foot between 1960 and 1973, in 1960 dollars, while comparable site-built homes became almost twice as expensive per square foot. The figures are from a Minneapolis Fed staff report by James Schmitz Jr., Elena Falcettoni and Mark Wright.
Credit
the US mobile home industry
2020
Robots frame module walls
Autovol opened a 400,000 sq ft plant in Nampa, Idaho, in July 2020 with more than 50 ABB six-axis industrial robots, in lines designed by the local robotics integrator House of Design. The robots frame walls, floors and ceilings for volumetric modules, fasten OSB or drywall to them, and cut the openings for windows, doors and electrical boxes. Building Design + Construction reported in 2022 that wires, plumbing, electrical boxes and insulation were still installed by hand at a separate station; Autovol's own site says the plant had nearly 270 staff in April 2026.
Credit
Autovol (Rick Murdock, Curtis Fletcher); House of Design
Watch for
Robotic microfactories cut time
Reframe Systems, started in 2022 by three former Amazon Robotics leaders, builds homes in 50,000 sq ft "microfactories" where vision-guided robot arms work at framing tables beside workers, and reports that it has cut costs by 35% and build times by 50%. HUD's research office relayed the figures; it did not measure them.
Achieved whenan outside party compares cost and build time on a set of Reframe homes with similar site-built homes.
Claimed by
Reframe Systems, April 2026
Frames in a working day
Promise Robotics, of Toronto, says its robot factories turn a builder's existing plans into walls, floors and stairs, and that its crews can assemble the frame of a typical two-story, 1,800 sq ft house with a basement and garage in about eight hours. D.R. Horton signed a multiyear agreement to use its factories for more than 1,250 homes. HousingWire notes the figures cover the structural frame, not a finished home.
Achieved whenD.R. Horton or an outside party publishes frame times and defect counts for homes built under the agreement.
Claimed by
Promise Robotics, October 2026
Open
01
Score wall-panel checks
A public test set of photos of finished, unsheathed wood wall panels on factory framing tables, each with hand-measured truth (stud positions, the size and place of each opening, and the two diagonals that show whether the panel is square), plus a script that scores any camera-checking tool against it.
The briefCredit · unclaimed02
A robot at rough-in
Rough-in is the stage where wiring, pipes and electrical boxes go into an open wall before it is closed. Build a low-cost robot arm that learns from human demonstrations to set electrical boxes against studs at the heights and sides marked on a panel's drawing, on a framed panel lying flat; a person fastens each box after the arm has moved away.
The briefCredit · unclaimed
Open 01 · the brief
Score wall-panel checks
The first to publish is credited on this line, and the deliverable moves from Open to Achieved.
What to build
A public test set of photos of finished, unsheathed wood wall panels on factory framing tables, each with hand-measured truth (stud positions, the size and place of each opening, and the two diagonals that show whether the panel is square), plus a script that scores any camera-checking tool against it.
Why it is still open
Roboflow, a computer-vision company, sells camera inspection for framing tables and nailing bridges in modular and manufactured-housing plants, and its page gives no accuracy figures. The research system of Martinez, Ahmad and Al-Hussein (2019) checked light-gauge steel frames on a prototype framing machine, and the 2025 data set of Rasool, Mei and Ahmad holds 285 images of 15 single timber studs, not assembled panels. Searches of Crossref, the web and GitHub for this brief found no public test set of wood wall panels.
Built with what exists
A phone or overhead camera; printed ArUco markers, square patterns that let software find scale and position; OpenCV and an open object-detection model such as YOLO; each panel's shop drawing exported from the plant's framing software.
First step
With one plant's permission, photograph 20 panels beside their shop drawings and measure each with a tape.
Done looks like
200 panels from at least two plants, each measured by hand, and a published table of each tool's error in stud position and opening position (in mm), its squareness error, and the share of real framing mistakes it caught.
Open 02 · the brief
A robot at rough-in
The first to publish is credited on this line, and the deliverable moves from Open to Achieved.
What to build
Rough-in is the stage where wiring, pipes and electrical boxes go into an open wall before it is closed. Build a low-cost robot arm that learns from human demonstrations to set electrical boxes against studs at the heights and sides marked on a panel's drawing, on a framed panel lying flat; a person fastens each box after the arm has moved away.
Why it is still open
In Autovol's plant, electrical boxes were still installed by hand in 2022. NREL's 2024 pilot had an industrial robot place and screw one electrical box and raceway to a stud, on a fixed prototype wall and along a path programmed in advance. Blueprint Robotics said in 2017 that outlets and switches were added by robot, with electricians standing by, and published no figures. Work on robots that learn timber assembly from demonstrations used industrial or collaborative arms on joints and trusses (Kramberger et al., 2022; Mozaffari et al., 2025), not rough-in.
Built with what exists
The open SO-101 arm from TheRobotStudio with Hugging Face's LeRobot software, or a small collaborative arm; one or two cameras; a policy model fine-tuned from demonstrations, such as NVIDIA's GR00T (see the Note "Five demonstrations per task").
First step
Record 50 demonstrations of placing one box on a 1.2 m practice panel and train a first policy.
Done looks like
50 filmed attempts on 10 panel layouts not used in training, with a published tally of boxes placed on the correct side of the stud and within 3 mm of the drawn height.