Industries / Construction and property / Commercial and residential construction / Drywall
Taping and finishing
Taping and finishing is the work of hiding the joints and screw heads between boards with paper or mesh tape and coats of joint compound, then sanding them smooth for paint.
4
Milestones achieved, from 1939 to 2015.
1
To watch for: announced, not yet confirmed outside.
3
Open deliverables. Nobody has shipped them.
The road
AchievedWatch forOpen
Achieved
1939
Taping by machine begins
A 2004 Walls & Ceilings history says that in 1939 the Ames brothers, painters and plasterers, began trying new ways to finish drywall and made the Corner Shoe, which pushed joint compound onto seams with air pressure through a long hose, the first of a long line of drywall tools. Dave Darnutzer's 2006 history for the same magazine also dates the first automatic tools to 1939 but credits "a California company". Ames Taping Tools, of Stone Mountain, Georgia, marked its 75th year in business in 2014.
Credit
the Ames brothers
1945
Tape and compound together
Ames built the forerunner of the automatic taper in 1945, a tool that lays tape and joint compound on a seam in one motion; it ran on a battery and weighed more than 100 lb (45 kg) when full. In the early 1950s Ames added boxes, which spread the finish coats over the seams. Many Ames patents expired in the early 1960s and other makers entered the market, but in 1995 Fine Homebuilding still described the automatic taper by Ames's trade name, Bazooka. Darnutzer writes that the mechanical tools were faster but much harder on the finisher's body, which led makers to air-driven tools from 1995, and a 2004 Walls & Ceilings article describes Ames's Power Assist Box, whose springs push the compound out for the finisher.
LessonA faster tool that wears out the person using it gets redesigned around the body.
Credit
Ames
c. 2002
German finish grades Q1–Q4
The German gypsum industry association's leaflet Merkblatt Nr. 2 grades filled board surfaces from Q1 to Q4. Q2 is the standard under the German construction contract rules (DIN 18340), and higher grades must be agreed and paid for; Q4 covers the whole surface with a layer more than 1 mm thick. In September 2004 the trade site Baulinks wrote that for about two years the leaflet had told architects how to specify finishes and not to write "malerfertig" (ready for the painter) or "streiflich frei" (free of marks under raking light).
LessonThe 2017 edition says that filled surfaces which look perfectly flat and free of shadows under raking light, light that skims along a wall at a low angle, cannot be made, even at Q4, so the lighting has to be known and agreed in advance.
Credit
Bundesverband der Gipsindustrie, Industriegruppe Gipsplatten
2015
Finish rules for glass mat
GA-214, the levels of finish that the Gypsum Association and three other trade bodies first published in 1990, grades a wall from Level 0 (no taping) to Level 5 (a skim coat over the whole surface); its 2022 edition says Level 5 is the right choice under gloss paint, dark paint or "critical lighting". In April 2015 the Gypsum Association published GA-214-2015 with AWCI, CISCA, PDCA and the Drywall Finishing Council. For the first time it included recommendations for gypsum panels without paper faces, such as glass-mat and fiber-reinforced boards, after several years of drafting and, in AWCI's words, "compromise on the part of all parties involved".
LessonBoards made to resist moisture and mold needed their own finishing rules.
Credit
Gypsum Association (Bob Wessel), AWCI, CISCA, PDCA and the Drywall Finishing Council
Watch for
Finishing robot claims triple speed
Origin, a startup, came out of stealth on 15 October 2026 with $20 million in funding co-led by Accel and Zacua Ventures. Its OG-1 robot applies compound, sands and primes walls up to 14 ft (4.3 m) high, pressing with controlled force when sanding, and has worked on New York jobsites. Origin says it works at three times human speed at human-level quality; Accel says five times. Walls & Ceilings noted that neither figure allows a like-for-like comparison with a finishing crew and that no price was given. Origin aims to have 150 robots deployed by the end of 2027.
Achieved whenA drywall contractor or independent party publishes results across finish levels, including how often people had to step in and how much rework followed.
Claimed by
Origin and Accel, October 2026
Open
01
Robot lays joint tape
A robot arm that lays paper tape bedded in joint compound along a flat seam between two boards on a bench wall, tested against a finisher on the same wall.
The briefCredit · unclaimed02
Checking a coat is dry
A test of quick ways to tell whether a coat of ready-mixed joint compound is dry enough for the next coat or for sanding: a thermal camera, since wet compound stays cooler while its water evaporates; a moisture meter; and a finisher's touch. Each is scored against the true answer, found by weighing coated board samples until their weight stops falling.
The briefCredit · unclaimed03
Find critical light from plans
A tool that reads a building model's windows, skylights and light fixtures, simulates the light falling on each wall, and marks where light grazes the surface at a low angle. Those are the "critical lighting" areas where joints show through paint and a Level 5 or Q4 finish is called for. Test it in rooms already finished to Level 4, against where finishers see joint shadows in photographs taken under the room's real light.
The briefCredit · unclaimed
Open 01 · the brief
Robot lays joint tape
The first to publish is credited on this line, and the deliverable moves from Open to Achieved.
What to build
A robot arm that lays paper tape bedded in joint compound along a flat seam between two boards on a bench wall, tested against a finisher on the same wall.
Why it is still open
Finishing robots apply compound and sand, but people still tape. Canvas's chief executive, Kevin Albert, told ENR in January 2022 that "workers do the taping", and in October 2026 Origin said it would only "eventually" take on taping. The idea is old on paper: US patent 5,279,700, filed in 1991 by Drywall Technologies of Maryland and granted in 1994, covers an automated process and apparatus for taping wallboard joints, and Canvas's 2018 patent application describes a robot that can apply tape. This research found no published test of a robot taping joints.
Built with what exists
A low-cost SO-101 arm on a vertical rail, as in WallFin, an open-source drywall sanding robot released under the Apache-2.0 license in October 2026, or a collaborative arm such as a UR10e; a hand taping tool that wets paper tape with compound as it feeds, of the kind Fine Homebuilding calls a banjo; the open LeRobot software to train the arm from recorded demonstrations (see the Note "Five demonstrations per task"); a camera to find the seam.
First step
Fix four boards to a bench frame and record 50 remote-controlled demonstrations of the arm laying 1 m of tape.
Done looks like
40 flat seams, each 1.2 m (4 ft) long, 20 taped by the robot and 20 by a finisher; after 24 hours each seam is cut and the tape lifted at five marked points to check for dry spots and blisters, and the tally is published with the time per seam.
Open 02 · the brief
Checking a coat is dry
The first to publish is credited on this line, and the deliverable moves from Open to Achieved.
What to build
A test of quick ways to tell whether a coat of ready-mixed joint compound is dry enough for the next coat or for sanding: a thermal camera, since wet compound stays cooler while its water evaporates; a moisture meter; and a finisher's touch. Each is scored against the true answer, found by weighing coated board samples until their weight stops falling.
Why it is still open
The Gypsum Association's guide GA-236 (2023) tells finishers to use its drying-time chart "rather than relying on moisture meters or visual observations to check for joint dryness". The chart is for one coat 1/16 in (1.6 mm) thick with adequate ventilation, and it warns that drying times above 48 hours or under 8 hours "are known to lead to poor results in many cases". The Infraspection Institute, which trains thermographers, wrote in October 2026 that the cooling of freshly applied compound "can be readily detected with a thermal imager", but gave no measure of how well the camera's call matches true dryness. This research found no such measurement.
Built with what exists
Board offcuts and ready-mixed joint compound; a scale reading to 0.1 g; a temperature and humidity logger; a phone-mounted thermal camera; a pinless moisture meter; Python to fit drying curves.
First step
Coat 10 samples at 1/16 in, weigh each every 30 minutes in one room, and log temperature and humidity alongside.
Done looks like
100 samples dried at five combinations of temperature and humidity, with each method's "dry" call compared with the time the sample's weight leveled off, and the error in hours published for each method and for the GA-236 chart.
Open 03 · the brief
Find critical light from plans
The first to publish is credited on this line, and the deliverable moves from Open to Achieved.
What to build
A tool that reads a building model's windows, skylights and light fixtures, simulates the light falling on each wall, and marks where light grazes the surface at a low angle. Those are the "critical lighting" areas where joints show through paint and a Level 5 or Q4 finish is called for. Test it in rooms already finished to Level 4, against where finishers see joint shadows in photographs taken under the room's real light.
Why it is still open
GA-214 says the design professional "shall clearly indicate" critical lighting areas on the plans, and the German leaflet says the lighting in later use must be known for a Q4 finish. AECOM Hunt's September 2026 quality bulletin still works from a checklist (long hallways, skylights, wall-washing lights) and warns that dropping Level 5 "without a thorough evaluation of lighting conditions" leads to disputes over the final appearance. General lighting software renders light on surfaces, but this research found no tool that maps critical lighting to finish levels.
Built with what exists
Radiance, the open-source lighting simulation engine, through the free Ladybug Tools; IfcOpenShell to read windows and fixtures from an IFC export of a Revit or ArchiCAD model; a phone camera at fixed exposure; Python.
First step
Model one hallway lit by wall-washing fixtures, map the angles at which light strikes its walls, and photograph the real hallway at night.
Done looks like
Ten built rooms, with the share of finisher-marked joint shadows that fall inside the tool's zones and the share of zones with no visible joints, published with the room models and photos.