BRENNEN

Industries / Construction and property / Commercial and residential construction / Drywall

Ceilings

This is the work of hanging a ceiling below the floor or roof above, either a metal grid that holds loose lay-in panels or a frame that gypsum board is screwed to.

5

Milestones achieved, from 1932 to 2013.

1

To watch for: announced, not yet confirmed outside.

2

Open deliverables. Nobody has shipped them.

The road

AchievedWatch forOpen

Achieved

  1. 1932

    Ceilings hung on a grid

    A suspended ceiling hangs from the structure above on wires or rods and leaves a hidden space, the plenum, for ducts, pipes and cables. The Mellon Institute in Pittsburgh built an experimental suspended ceiling as early as 1932, and Burgess and the Rivet Grip Company sold commercial systems by 1936, by architectural historian Keith Peiffer's account. The US National Park Service also dates acoustical panel ceilings, lay-in panels in a T-shaped metal grid, to the 1930s.

    acsa-arch.orgnps.gov

    Credit

    Mellon Institute; Burgess; Rivet Grip Company

  2. 1957

    Lay-in panels become standard

    In 1957 the Armstrong Cork Company introduced Acoustical Fire Guard, mineral panels in 2 by 2 ft and 2 by 4 ft sizes set loose in a suspended metal grid, and in 1960 a lay-in ceiling using it was rated by Underwriters Laboratories to protect steel above it from fire for three hours. Peiffer reports that sales of acoustical suspended ceilings rose fivefold from 1947 to 1956, and that Armstrong's own history calls the product "the most important event in commercial ceilings history".

    acsa-arch.org

    Credit

    Armstrong Cork Company (now Armstrong World Industries)

  3. 1988

    Robots lift ceiling boards

    Shimizu described its CFR-1 robot in 1988: it lifted gypsum ceiling boards of 13.5 kg and 910 by 1,820 mm into place without scaffolding while a worker drove the screws, and Shimizu reported work 50% faster on site. Tokyu Construction published another scaffold-free ceiling board robot in 1998, and Shimizu's Robo-Buddy, shown to reporters in 2018, picked up boards by suction and fixed them in place itself. Yet in 2018 Shimizu's Masahiro Indo told the Associated Press that its robots could handle only about 1% of construction work.

    LessonHolding a board overhead was automated decades ago, but moving between bays and fixing boards on a changing site kept people on the job.

    iaarc.orgjstage.jst.go.jpclaimsjournal.com

    Credit

    Shimizu Corporation; Tokyu Construction

  4. 2011

    Christchurch ceilings fail twice

    After the 22 February 2011 Christchurch earthquake, Rajesh Dhakal and Greg MacRae of the University of Canterbury, with Keith Hogg of the ceiling firm Hush Interiors, found ceilings to be the most severely damaged non-structural part of buildings: two-thirds of the office buildings they visited had more than trivial damage to suspended ceilings, while plasterboard ceilings in houses fared much better. Many ceilings reinstalled after the September 2010 Darfield earthquake failed again in the same way. They blamed weak grid members and connections, such as single small rivets at the wall angle, and heavy tiles of 16 kg/m² or more, and noted that lighter tiles were "rapidly becoming popular".

    LessonPutting a ceiling back the way it was builds in the same failure.

    bulletin.nzsee.org.nz

    Credit

    R. P. Dhakal, G. A. MacRae and K. Hogg (Bulletin of the New Zealand Society for Earthquake Engineering)

  5. 2013

    Japan makes ceiling rules law

    After the 2001 Geiyo earthquake, Japan's building ministry (MLIT) issued advice to brace ceiling rods diagonally and leave a gap around suspended ceilings. In the 2011 Great East Japan Earthquake ceilings still fell in gymnasiums, theaters, shops and factories, including the auditorium of Kudan Kaikan in Tokyo: MLIT counted about 2,000 cases reported by the Japan Federation of Construction Contractors and, from press reports, 5 deaths and more than 72 injuries. Rules issued in July and August 2013 and in force from April 2014 now cover "specified ceilings", suspended ceilings more than 6 m up, over 200 m² and heavier than 2 kg/m² in spaces people use every day.

    LessonAdvice was not enough to change how ceilings were hung; binding rules came only after deaths.

    mlit.go.jpatcouncil.orgkenken.go.jpnilim.go.jpjstage.jst.go.jp

    Credit

    MLIT; National Institute for Land and Infrastructure Management (NILIM); Building Research Institute (BRI)

Watch for

  1. Robots fix ceiling boards

    Kajima and the robot maker tmsuk built a robot that, once a worker marks the area on a tablet, measures its position against the ceiling frame, moves itself and fixes ceiling boards. On a Kajima office building site, two robots and one worker did the board work that two skilled workers do by hand, Kajima reported. In 2024 tmsuk had shown prototype robots for each step of a grid ceiling: hanging bolts, main and cross T-bars, and boards.

    Achieved whenA contractor other than Kajima, or an independent party, publishes the area installed per shift and the defect rate on a real job against a hand crew.

    newswitch.jptmsuk.co.jp

    Claimed by

    Kajima, reported by Nikkan Kogyo Shimbun, July 2026

Open

  1. 01

    Check ceiling bracing by photo

    An open set of labeled photos of the hidden side of suspended ceilings, the grid, hanger wires, diagonal brace wires, struts and wall connections, taken on full-size mock-up bays with planted faults, and a public test of a vision model that checks each photo against an installer's checklist before the panels go in. Faults would include a slack or missing brace wire, a missing strut, a grid fixed tight to the wall where a gap is needed, a single small rivet at a wall connection and too few hangers.

    The brief
    Credit · unclaimed
  2. 02

    One table of ceiling falls

    A public table of suspended ceilings that fell or were damaged in earthquakes since 2010, one row per case, giving the ceiling type, panel weight per m², height, area, bracing, building age and injuries, each row linked to the report page it came from.

    The brief
    Credit · unclaimed

Open 01 · the brief

Check ceiling bracing by photo

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

An open set of labeled photos of the hidden side of suspended ceilings, the grid, hanger wires, diagonal brace wires, struts and wall connections, taken on full-size mock-up bays with planted faults, and a public test of a vision model that checks each photo against an installer's checklist before the panels go in. Faults would include a slack or missing brace wire, a missing strut, a grid fixed tight to the wall where a gap is needed, a single small rivet at a wall connection and too few hangers.

Why it is still open

Dhakal, MacRae and Hogg traced many Christchurch failures to the details of these hidden connections, which are covered up once the panels are in. Published vision work looks at ceilings from below, after the damage: Wang, Kawaguchi and Wang trained a model on 1,953 photos of damaged ceilings in large halls and reached 86.22% accuracy (2020), and Guo and colleagues found warped panels with 92.2% accuracy (2025). This research found no image set of bracing faults above a ceiling.

bulletin.nzsee.org.nzapi.semanticscholar.orgapi.semanticscholar.org

Built with what exists

A supplier's standard grid kit, hanger wire and panels hung from a timber frame about 1.2 m off the floor, so no one works at height; a maker's seismic installation guide or Japan's 2013 technical standard for the checklist; a phone camera; an open object detector such as a YOLO-family model, or a vision-language model asked fixed yes-or-no checklist questions (see the Note "A thousand questions, one pass").

  1. First step

    Build one 2.4 by 2.4 m bay on a low frame, plant five faults, and photograph each from five angles.

  2. Done looks like

    At least 400 labeled photos of at least 40 mock-up bays released under an open license, then 20 new bays with planted faults scored by the model and by an experienced ceiling installer, with a published tally of faults each missed and false alarms each raised.

Open 02 · the brief

One table of ceiling falls

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

A public table of suspended ceilings that fell or were damaged in earthquakes since 2010, one row per case, giving the ceiling type, panel weight per m², height, area, bracing, building age and injuries, each row linked to the report page it came from.

Why it is still open

Pooled records exist, but they stop before the earthquakes that taught the most about ceilings. Kao, Soong and Vender's Nonstructural Damage Database, published in 1999, holds nearly 3,000 entries from more than 50 earthquakes since 1964, and Taghavi and Miranda's 2003 PEER database covers the nonstructural parts of commercial buildings. NIST's newer Nonstructural Element Database pools more than 2,000 laboratory test records, not field cases. For 2011, MLIT's briefing counts about 2,000 ceiling falls in the Great East Japan Earthquake as a single number from a contractors' federation, BRI's 2019 report works through 13 field cases, and after Christchurch Dhakal and colleagues wrote that the share of buildings with each type of damage could not yet be given. This research found no case-level table for the earthquakes since 2010.

nehrpsearch.nist.govpeer.berkeley.eduescholarship.orgmlit.go.jpkenken.go.jpbulletin.nzsee.org.nz

Built with what exists

Earthquake survey reports, such as the NZSEE Bulletin papers, BRI and NILIM reports and Architectural Institute of Japan papers on J-STAGE; the fields of the earlier databases as a starting schema; Python and pandas; an AI model that pulls fields from report text and translates Japanese (see the Note "The jobs agents repeat"); a second person to check a sample of rows.

  1. First step

    Code the 13 BRI field cases and the cases described in the 2011 Christchurch paper into a first table.

  2. Done looks like

    At least 300 cases from at least four earthquakes since 2010 in at least two countries, published as a CSV file under an open license with a source page for every row, and the agreement between two people coding the same 50 cases reported for each field.