BRENNEN

Industries / Construction and property / Commercial and residential construction / Concrete

Reinforcement

Reinforcement is the steel, or sometimes glass-fiber bar, that is placed and tied inside the forms before the pour so the hardened concrete can carry the pulling forces it cannot carry alone.

6

Milestones achieved, from 1867 to 2022.

1

To watch for: announced, not yet confirmed outside.

2

Open deliverables. Nobody has shipped them.

The road

AchievedWatch forOpen

Achieved

  1. 1867

    A gardener's wired tubs

    Joseph Monier, a French gardener, received a patent in 1867 for containers of cement mortar reinforced with iron wire. In 1878 he patented bar reinforcement for full-size concrete structures, which spread to many countries under license as the système Monier.

    lex.dk

    Credit

    Joseph Monier

  2. 1884

    Bars twisted to grip

    Ernest L. Ransome of San Francisco patented iron or steel bars twisted along their length (US patent 305,226, 16 September 1884), so that the spiral grips the concrete at every point and the bar cannot slide as it stretches.

    patents.google.com

    Credit

    Ernest L. Ransome

  3. 1947

    A standard for the ribs

    ASTM A305 set minimum requirements for the deformations, the raised ribs rolled onto steel bars, to improve their bond with concrete. In 1968 its rules were folded into ASTM A615, the specification for deformed bars that replaced it.

    fhwa.dot.gov

    Credit

    ASTM; account by the Federal Highway Administration

  4. 1986

    Coated bars corrode in Florida

    Epoxy-coated bars, meant to resist rust from road salt and seawater, were first used in a US highway bridge in 1973, a deck over the Schuylkill River in Pennsylvania, and 40 decks in 18 states and the District of Columbia had them by 1976 under an FHWA program. In 1986 Florida reported that the Long Key Bridge showed corrosion only six years after it was built, and a later survey by Alberto Sagüés and colleagues found the coating had lost its bond on 29 of 30 Florida marine substructures four years or older.

    LessonA coating that serves in salted decks can fail in the sea, and whether it stays bonded to the steel has to be checked in the field, not assumed.

    fhwa.dot.govvtechworks.lib.vt.edu

    Credit

    FHWA; Florida Department of Transportation; Sagüés and colleagues, University of South Florida

  5. 2017

    A robot ties a deck

    In October 2017, on the Freedom Road bridge in Beaver County, Pennsylvania, a prototype robot called TyBot, working from a frame that spans the deck, tied more than 24,000 rebar crossings at 5.5 seconds each, ENR reported. A Pennsylvania DOT district executive said the ties were tight but that it missed spots where a support chair sat too close to the crossing, which is why a person watched it. Its maker says the third version, sold from 2025, has had more than 65 field deployments and ties more than 1,200 crossings an hour.

    enr.compowerprogress.com

    Credit

    Stephen Muck, Brayman Construction; Jeremy Searock and staff from Carnegie Mellon University's Robotics Institute, Advanced Construction Robotics

  6. 2022

    A code for glass-fiber bars

    ACI CODE-440.11-22, in effect from 2 September 2022, lets engineers design concrete buildings with bars of glass-fiber-reinforced polymer (GFRP), which do not rust, in place of steel; the American Concrete Institute calls it the first comprehensive building code for such bars. It covers all members in Seismic Design Category A, only members outside the earthquake-resisting system in Categories B and C, none in D to F, and only where no fire-resistance rating is required.

    concrete.orgconcrete.org

    Credit

    ACI Committee 440

Watch for

  1. Bar insertion learned in simulation

    Tao Sun, Abhishek Gupta, Szymon Rusinkiewicz, Yi Shao and co-authors report that a robot policy trained only in simulation, then run from camera images, seated rebars from a real factory production run into place at 1.4 mm clearance in 91.3% of real-robot attempts, with no real-world training data.

    Achieved whena group outside the authors' labs runs the released code and task assets on its own robot and bars and publishes its success rate, or a rebar fabricator reports counts from production use.

    arxiv.org

    Claimed by

    the authors, arXiv preprint, September 2026

Open

  1. 01

    A shared rebar-tying test

    A standard bench mat and scoring rules for rebar-tying robots: a mat of 13 mm bars on chairs with plain, crowded and two-layer crossings, scored on the share tied, ties that let the bars slip under a fixed push, and seconds per tie, with results published for at least two systems and for a person tying by hand.

    The brief
    Credit · unclaimed
  2. 02

    Coating damage measured by camera

    A phone app that photographs epoxy-coated bars at the site, before or after they are placed, measures the share of the coating that is damaged in each 1 ft (300 mm) of bar, and says whether that section passes the jobsite limits, scored against careful hand measurement on the same bars.

    The brief
    Credit · unclaimed

Open 01 · the brief

A shared rebar-tying test

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

A standard bench mat and scoring rules for rebar-tying robots: a mat of 13 mm bars on chairs with plain, crowded and two-layer crossings, scored on the share tied, ties that let the bars slip under a fixed push, and seconds per tie, with results published for at least two systems and for a person tying by hand.

Why it is still open

Laboratory systems are each scored on their own meshes. OpenTie (Fan and colleagues, August 2025) ties without training, Wang and colleagues (August 2025) plan ties from 5 to 10 demonstrations, GitHub holds tying code for a Fairino arm (123CHENJINHUA/rebar-tying), a tie-state recognizer (orange0131/rebar-tying-perception) and 254 on-site photos of a tying robot (Txinyan/On-site-image-data-of-the-rebar-tying-robot), and TyBot's speed figures are its maker's own. None uses a common mat or score.

arxiv.orgarxiv.orggithub.com

Built with what exists

A robot arm with about 5 kg payload, such as a Fairino FR5 or UFactory xArm 6, carrying a battery rebar tier such as MAX's Twintier; an Intel RealSense D435 depth camera; a policy trained from a few demonstrations, for example NVIDIA's GR00T 2 (see the Note "Five demonstrations per task"), alongside the published OpenTie method; a push gauge for the slip test.

  1. First step

    Build a 1.2 m by 1.2 m mat of 13 mm bars on chairs and film a person tying 100 crossings to set the human baseline for time and misses.

  2. Done looks like

    The mat drawings and rules published, and each system's 200 filmed attempts with a tally of tied, missed and loose crossings and the time per tie, next to a person's 200.

Open 02 · the brief

Coating damage measured by camera

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

A phone app that photographs epoxy-coated bars at the site, before or after they are placed, measures the share of the coating that is damaged in each 1 ft (300 mm) of bar, and says whether that section passes the jobsite limits, scored against careful hand measurement on the same bars.

Why it is still open

The limits come from ASTM D3963 and ACI 301: a bar with more than 2% of its coating damaged in any 1 ft section should be replaced, and one with more than 5% covered by patching may be rejected, as the Epoxy Interest Group's field guide sets them out. The check is a visual assessment. The instruments in use are electrical holiday detectors, such as California Test 685, which find pinholes that may not be visible at all, not the area of visible damage. Camera systems that grade coating breakdown exist for marine and offshore steel structures, and a search found none that measures damaged area on coated bars. The Florida failures under Achieved show why the coating's condition matters.

epoxyinterestgroup.orgdot.ca.govdoi.org

Built with what exists

A phone camera; a printed scale strip with ArUco markers laid beside the bar; OpenCV; Meta's SAM 2 segmentation model to separate green coating from bare steel and patch material; Python; offcuts of epoxy-coated bar from a fabricator, damaged with a file to known areas.

  1. First step

    Get 20 offcuts of 16 mm (#5) coated bar, file damage of known size onto them, and photograph them at three distances to see how small a scratch the camera can resolve.

  2. Done looks like

    200 one-foot sections photographed in sun and shade and measured by hand by tracing the damage on clear film; the app's damage share within 0.5 percentage points of the hand figure on at least 90% of sections, and its pass or fail call matching the hand call on at least 95%; all photos and measurements published.