Industries / Construction and property / Commercial and residential construction
Foundations and structure
This is the work of digging, setting foundations and putting up the frame, in concrete, steel, timber, masonry or factory-made parts, that carries a building's weight to the ground.
7
Milestones achieved, from 1824 to 2025.
2
To watch for: announced, not yet confirmed outside.
2
Open deliverables. Nobody has shipped them.
In depth
The same ground is charted in more depth, as industries of their own.
The road
AchievedWatch forOpen
Achieved
1824
Portland cement is patented
Joseph Aspdin, a bricklayer in Leeds, patented a cement made by burning limestone with clay and named it after Portland stone. Cement of this kind became the binder in modern concrete and mortar. Sources disagree on who made the first modern version: Historic England credits Isaac Charles Johnson, who made commercial Portland cement at Swanscombe, Kent, about 21 years later, and the Science History Institute credits Aspdin's son William, who found that clinker, the hard over-burned lumps from the kiln, made a stronger cement.
Credit
Joseph Aspdin for the patent; William Aspdin or Isaac Charles Johnson for the modern product
1892
Reinforced concrete goes commercial
François Hennebique patented a system of concrete with metal bars set inside it. The bars carry the pulling forces that concrete alone cannot. He did not build himself but licensed established contractors to use the system under strict rules. Historic England calls it "the first to be commercially successful and widely used", and dates the first British building to use it, Weaver's Mill in Swansea, to 1898.
Credit
François Hennebique
1968
Ronan Point partly collapses
On 16 May 1968 a gas explosion in a flat of a new tower block in east London blew out a load-bearing outer wall, and the floors above that corner fell one onto the next. Four people died and 17 were injured. The block was built from large precast concrete panels. The public inquiry found the designers "did not take into account the abnormal", and recommended that the Building Regulations require buildings that "are not susceptible to progressive collapse".
LessonA building must survive the loss of one part without the rest following it down.
Credit
the inquiry chaired by Hugh Griffiths QC (HMSO, 1968)
2013
Rana Plaza collapses
On 24 April 2013 a building full of garment factories collapsed near Dhaka, Bangladesh, killing more than 1,100 workers by Amnesty International's count. Cracks had been seen in its walls the day before and the building had been shut, but managers made staff go back in. On 13 May 2013, clothing brands and trade unions signed the Accord on Fire and Building Safety in Bangladesh, which set up inspections of supplier factories against building, fire and electrical safety standards under an independent Safety Inspector.
LessonCracks in a loaded building mean work stops, and the people who profit from a building cannot be the ones who decide it is safe.
Credit
the Accord's signatories, brands, retailers and trade unions
2022
Timber reaches 25 stories
The Council on Tall Buildings and Urban Habitat (CTBUH) certified Ascent in Milwaukee, 86.6 m (284 ft) and 25 stories, as the world's tallest timber building. Most of its frame is cross-laminated timber (CLT), boards glued in crosswise layers into large panels, and glulam, glued layered timber beams and columns, on a concrete base. In the US, the 2021 International Building Code added three tall mass-timber construction types, the most fire-protected allowing up to 18 stories, after the code committee ran five full-scale fire tests.
Credit
Korb + Associates (architect), Thornton Tomasetti (engineer) and New Land Enterprises (developer); CTBUH; International Code Council
2025
A robot lays house walls
FBR's Hadrian X is a truck-mounted robot that lays concrete blocks and bonds them with adhesive. The homebuilder PulteGroup announced on 20 February 2025 that it had built the structural walls of a home at Babcock Ranch, Florida, and said it was one of 10 US homes built with the robot.
Credit
FBR (Fastbrick Robotics, Australia); PulteGroup
2025
Printed barracks are occupied
On 29 January 2025 the US Army opened three barracks with 3D-printed concrete walls, two at Fort Bliss, Texas, and one at Camp McGregor, New Mexico, each 5,700 sq ft and housing up to 56 soldiers. The Army calls them the Defense Department's first 3D-printed barracks, printed by ICON with its Vulcan printer. In July 2026 the Army Corps of Engineers marked the first of ten more as complete. In December 2023, ISO and ASTM published ISO/ASTM 52939, which sets quality rules for printed load-bearing building parts.
Credit
ICON (Austin, Texas); US Army and its Corps of Engineers; ISO and ASTM
Watch for
Bricklaying robots for hire
Monumental, of Amsterdam, says it has more than 150 small electric bricklaying robots on European job sites, charges by the brick or square meter like a subcontractor, and plans to start in four US states in 2026. Fortune reported a $32 million funding round; the robot count is the company's own.
Achieved whenA named contractor or an independent body reports finished brickwork from these robots, with its quantity and inspection results.
Claimed by
Monumental, July 2026
Printed apartment houses in series
PERI 3D Construction and the builder KRAUSGRUPPE are printing DREIHAUS, a three-story apartment design, in Heidelberg, Germany, printing one half of each house while the floor slab is poured on the other. They claim it is 30% faster and 10% cheaper than conventional building, figures their release says "are to be demonstrated in practice".
Achieved whenMeasured time and cost figures are published and checked by someone outside PERI and its partners.
Claimed by
PERI, October 2025
Open
01
Shear-wall nailing checker
A phone tool that finds the nail heads on a sheathed wall panel and reports their spacing at the panel edges and in the field against the engineer's nailing schedule. A shear wall is a wall sheathed in plywood or oriented strand board (OSB) that holds a building up against wind and earthquakes, and it works only if the nails are close enough together.
The briefCredit · unclaimed02
Mortar joint gauge
A phone tool that measures the width of every horizontal (bed) and vertical (head) mortar joint in a photo of a new brick or block wall and flags joints outside the width the job specifies.
The briefCredit · unclaimed
Open 01 · the brief
Shear-wall nailing checker
The first to publish is credited on this line, and the deliverable moves from Open to Achieved.
What to build
A phone tool that finds the nail heads on a sheathed wall panel and reports their spacing at the panel edges and in the field against the engineer's nailing schedule. A shear wall is a wall sheathed in plywood or oriented strand board (OSB) that holds a building up against wind and earthquakes, and it works only if the nails are close enough together.
Why it is still open
A patent for a nailing guide says that when a crew aims for 3-inch spacing by eye, the measured spacing "may be four inches in places". A vision software vendor lists nail-pattern checking as a possible use but gives no deployments, data or accuracy figures, and this research found no public labeled dataset.
Built with what exists
Mock panels nailed by hand with a hammer; a phone camera and a printed scale target; an open object-detection model; a tape measure for the true spacing.
First step
Nail two panels, one correct and one with planted errors, and mark the nail heads by hand in 20 photos.
Done looks like
Ten 4 ft by 8 ft mock panels with 40 known nailing errors among correct nails, 200 photos, and a published dataset with a tally of errors caught, missed and falsely flagged, and the spacing error in inches against the tape.
Open 02 · the brief
Mortar joint gauge
The first to publish is credited on this line, and the deliverable moves from Open to Achieved.
What to build
A phone tool that measures the width of every horizontal (bed) and vertical (head) mortar joint in a photo of a new brick or block wall and flags joints outside the width the job specifies.
Why it is still open
A 2025 survey of machine vision for masonry finds the work focused on cracks in historic buildings and cites a shortage of labeled masonry images. This research found no tool or study that measures joint widths on new walls against a tolerance.
Built with what exists
A small test wall about 1 m by 1 m laid with deliberately uneven joints; calipers; a phone with a scale target; an existing open brick-and-mortar image segmentation model.
First step
Build the wall and measure 50 joints with calipers.
Done looks like
300 joints measured both by caliper and by the tool, with the mean error in millimeters and a tally of out-of-range joints caught and missed, all published.