BRENNEN

Industries / Industrial equipment and services / Industrial machinery / Valves

Testing

Testing is the set of pressure, leak, fire and flow checks that a valve, or a sample of its design, goes through at the factory or in a laboratory before it is sold or approved.

5

Milestones achieved, from 1935 to 2025.

1

To watch for: announced, not yet confirmed outside.

2

Open deliverables. Nobody has shipped them.

The road

AchievedWatch forOpen

Achieved

  1. 1935

    Relief valves flow-tested

    A pressure relief valve opens to let fluid out before a vessel bursts, and its rated capacity says how much it can let out. The National Board of Boiler and Pressure Vessel Inspectors sponsored relief valve tests at Ohio State University's Robinson Mechanical Engineering Laboratory in 1935, when design testing was added to the ASME Code for safety valves. It built its own laboratory in 1974, began testing samples picked at random from production in 1976 and opened its present laboratory in 1991, which by the Board's count ran 53,804 tests in its first 30 years. Certified designs are listed in the Board's free NB-18 database, and each certification lasts six years.

    nationalboard.orgnationalboard.org

    Credit

    National Board of Boiler and Pressure Vessel Inspectors; Ohio State University

  2. 1961

    Pressure tests written down

    When the American Petroleum Institute (API) first published API 600, its standard for steel gate valves in refineries, in 1939, the test rule was simply that a valve must not leak, by the account of Greg Johnson in Valve Magazine. The Manufacturers Standardization Society (MSS) published SP-61, "Pressure Testing of Valves", in 1961, and API followed in 1968 with API 598, "Valve Inspection and Test", which Johnson calls the most widely used valve testing standard in the United States.

    valvemagazine.com

    Credit

    Manufacturers Standardization Society; American Petroleum Institute

  3. 1976

    Leakage classes for control valves

    A control valve is built to throttle flow, and not every design is meant to shut off completely. ANSI B16.104 of 1976, since replaced by ANSI/FCI 70-2 of the Fluid Controls Institute, sets six classes of seat leakage, the flow that still passes a closed valve, each with its own shop test. Class IV, for metal plugs on metal seats, allows 0.01% of the valve's full-open capacity in a test with air at 45 to 60 psig (3.1 to 4.1 bar); Class VI, for soft seats of a resilient material such as PTFE, allows from 0.15 ml of air a minute for a 1-inch valve to 6.75 ml for an 8-inch valve, counted as bubbles, by the account of the valve maker SVF Flow Controls.

    svf.netenxstandards.web.illinois.edu

    Credit

    Fluid Controls Institute; American National Standards Institute

  4. 1994

    Fire tests at low pressure

    A fire test burns a closed valve for 30 minutes in flames of 760 to 982 °C, then measures what leaks through it and out of it. Exxon had one of the earliest fire tests, in which a valve pressurized with kerosene was burned, a test that endangered the people running it; after a large fire at one of its Baton Rouge chemical plants in 1994, it accepted valves qualified to the fourth edition of API 607, released that year. That edition was the first to test soft-seated valves, whose seats are plastic, at a lower pressure as well, because line pressure can fall in a plant fire once pumps stop.

    Lessonball valves of 3 to 4 inches had the most trouble, because their seats burned only partly and the leftover char could lodge between ball and body.

    valvemagazine.com

    Credit

    American Petroleum Institute; Exxon

  5. 2025

    Certified in pure hydrogen

    ISO 15848-1 is the international type test for gas leaking from a valve's stem and body seals, usually run with helium or methane, and hydrogen, a smaller molecule, escapes through seals more easily. In February 2025 Trillium Flow Technologies said that TÜV SÜD, a testing and certification company, had certified its Blakeborough control valves after tests in 99.9% pure hydrogen at cryogenic and room temperatures, which met tightness class A, the tightest, at endurance classes CO1 and CC1 of ISO 15848-1.

    trilliumflow.com

    Credit

    TÜV SÜD; Trillium Flow Technologies

Watch for

  1. A 500 bar hydrogen valve

    HEROSE of Germany says its Type 01C07 globe valve, for tube trailers and other transportable hydrogen containers at up to 500 bar, passed hydrogen leak tests across its whole operating temperature range and 10,000 full pressure cycles, and has entered service in the first systems of a global gas supplier it developed the valve with.

    Achieved whena notified body or the gas supplier publishes the test results or a service record.

    themachinemaker.com

    Claimed by

    HEROSE, August 2026

Open

  1. 01

    Check test reports by machine

    An open checker that reads a valve's factory test report, as a PDF or a photo, and checks that every test the order calls for is present (shell, backseat and seat tests), that pressures and hold times meet the limits for the valve's size and pressure class, and that the recorded leakage is within the allowance of the standard named. The limits are entered by the user from a licensed copy of the standard. It is published with a test set of made-up reports carrying planted errors.

    The brief
    Credit · unclaimed
  2. 02

    Robot leak sniffing, tallied

    A low-pressure bench where a robot arm sweeps a helium sniffer, a probe that draws in air and detects helium, over a valve's stem seal, bonnet joint and end connections, on valve designs it was not trained on, with calibrated helium leaks hidden at random points, and a filmed, published count of leaks found by the robot and by a trained person on the same valves.

    The brief
    Credit · unclaimed

Open 01 · the brief

Check test reports by machine

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

An open checker that reads a valve's factory test report, as a PDF or a photo, and checks that every test the order calls for is present (shell, backseat and seat tests), that pressures and hold times meet the limits for the valve's size and pressure class, and that the recorded leakage is within the allowance of the standard named. The limits are entered by the user from a licensed copy of the standard. It is published with a test set of made-up reports carrying planted errors.

Why it is still open

Buyers' guides still hand people a checklist to work through by hand. STV Valves' 2025 guide lists valve identity, standard, test pressures, test medium, durations, leakage and inspector sign-off, and its red flags include missing tests and pressure not held for the full time. The nearest open tool, MillProof (GitHub, November 2026), has Claude read steel mill test certificates and checks them with fixed rules for IS 2062 and ASTM A36 plate, not valve pressure tests, and a GitHub search in November 2026 found no repository for valve test certificates.

stvvalves.comgithub.com

Built with what exists

An AI model that reads documents and photos, such as Claude (the Note "Seven more flagged" covers a Claude-based reviewer that found issues people had missed in long records); fixed rules in Python for each pass or fail; a table of limits supplied by the user; made-up reports generated from document templates.

  1. First step

    Write 30 made-up reports for gate and ball valves in two pressure classes, plant 10 errors, and score a first version against them.

  2. Done looks like

    On 300 made-up reports holding 100 planted errors of six kinds (missing test, low pressure, short hold, wrong test medium, leakage over the allowance, mismatched serial number), the checker finds at least 95 with no more than 10 false flags; the same scoring on at least 50 real reports, with names removed, from buyers who agree to share them.

Open 02 · the brief

Robot leak sniffing, tallied

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

A low-pressure bench where a robot arm sweeps a helium sniffer, a probe that draws in air and detects helium, over a valve's stem seal, bonnet joint and end connections, on valve designs it was not trained on, with calibrated helium leaks hidden at random points, and a filmed, published count of leaks found by the robot and by a trained person on the same valves.

Why it is still open

Neles told Valve Magazine in 2021 that it runs high-pressure helium tests with a collaborative robot and a sniffing program inside an explosion-proof enclosure, and Arçelik's air conditioner plant in Turkey uses a UR5e collaborative robot with a sniffer probe, guided by Mech-Mind cameras to each weld (Assembly Magazine, October 2025). Neither reports how many leaks the robot finds, and Valve Magazine wrote in April 2026 that the wide mix of valve sizes and types makes automation harder for valve makers than for high-volume plants.

valvemagazine.comassemblymag.comvalvemagazine.com

Built with what exists

A low-cost arm such as the SO-101 with Hugging Face's LeRobot software (the Note "No download"); a policy learned from a few demonstrations, such as NVIDIA's GR00T 2 (the Note "Five demonstrations per task"); a helium sniffer leak detector; calibrated helium reference leaks; small valves filled with helium, which does not burn, at no more than 2 bar; a camera to film each trial.

  1. First step

    Fit one reference leak to a small ball valve at low pressure and film a person sweeping it 20 times, as the first demonstrations.

  2. Done looks like

    On 10 valve designs not used in training, 100 trials, each with a reference leak at one of four points chosen at random; the share of leaks found and the minutes per valve for the robot and for a person, published with the film and the raw sniffer readings.