Industries / Mining and materials / Steel and metals / Tool and die
Machining
Machining cuts die and mold steel to its final shape by boring, milling, grinding and spark erosion, often after the steel has been hardened.
5
Milestones achieved, from 1921 to 2003.
1
To watch for: announced, not yet confirmed outside.
2
Open deliverables. Nobody has shipped them.
The road
AchievedWatch forOpen
Achieved
1921
Holes placed by machine
A jig borer is a very rigid machine that bores holes at exactly measured positions, and it is used to make jigs and dies. The Société Genevoise d'Instruments de Physique (SIP) in Geneva developed it from a 1912 machine for marking out watch plates, and built its first industrial jig borer in 1921 for the Royal Small Arms Factory at Enfield, England. The Science Museum, which holds that machine, notes that Pratt & Whitney had brought out a jig-boring machine in 1917, and that a jig borer should be kept in a room at constant temperature.
Credit
Société Genevoise d'Instruments de Physique; Pratt & Whitney
1921
A tracer copies the die
Keller Mechanical Engineering of Brooklyn shipped its first die-sinking machine with an electric tracer to the Budd Company in Philadelphia in March 1921. A stylus followed a pattern of the die and steered the cutter, which by the account in New York University's Keller archive gave more accurate stamping and forging dies and casting molds. By 1930 the company had shipped over 4,000 machines, and "Kellering" had become a verb in the tool and die trade.
Credit
John C. Shaw, with Joseph F. and Sidney A. Keller, Keller Mechanical Engineering
1969
A wire cuts by numbers
Wire EDM (electrical discharge machining) cuts through hardened steel with a thin moving wire that wears metal away with sparks, so a punch or a die opening can be cut to a programmed outline after heat treatment. Agie of Switzerland launched a numerically controlled wire EDM machine in 1969; Modern Machine Shop, reporting the company's history in 2012, called it the world's first.
Credit
Agie, now the Agie Charmilles brand of United Machining
1999
Milling hard steel replaces EDM
Mold shops used to mill steel to within about 0.015 inch (0.4 mm) of its final shape, harden it, and remove the rest by EDM. Creative Die Mold, a 72-person shop in Glendale Heights, Illinois, began finishing hardened molds on a Yasda machining center at 10,000 rpm, with cuts no deeper than 0.009 inch (0.23 mm) and a machine frame held within ±0.2 °C through cycles of eight hours. By 1999 it machined many molds with no EDM at all, Modern Machine Shop reported.
LessonThe shop first made EDM electrodes for molds that were then finished entirely by milling and had to throw them away; EDM stayed for deep grooves and sharp inside corners.
Credit
Creative Die Mold; Yasda Precision
2003
Robots feed the machines
In a mold shop almost every part is different, so automation came first to EDM electrodes, which are made in numbers. Omega Plastics of Clinton Township, Michigan, linked its EDM to a System 3R robot in 2003, then added a graphite mill so the robot could keep the EDM supplied for a whole weekend unattended. By 2017 nearly every part in its cell, from electrodes to mold blocks of about 90 kg (200 pounds), moved on pallets that return to position within ±0.002 mm, Modern Machine Shop reported.
LessonThe shop says automating one-off work depends on a standard process for every job, cut straight to the CAD model.
Credit
Omega Plastics; System 3R
Watch for
An AI agent plans cuts
CAM (computer-aided manufacturing) software turns a 3D model into instructions for the machine. Cimatron says its CAM Agent, built with Limitless Labs, proposes a full milling strategy from a shop's own part, stock and tool library, and lets a programmer check each step; at the IMTS show in 2026 it ran a roughing-to-finishing sequence on a mold-like part in a few minutes. The tool is in beta, and Cimatron had no efficiency data or case study to show.
Achieved whenshops or an outside tester publish programming time, machining time and accuracy for AI-planned mold parts against programs written by people.
Claimed by
Cimatron, to MoldMaking Technology, October 2026
Open
01
AI against a mold programmer
A public comparison on ten mold insert test parts, each with a freeform face, deep ribs and small inside corners. Each part is programmed twice, once by an AI CAM tool or AI agent and once by an experienced mold programmer. Both programs are cut on the same machine in machining wax or aluminum, and the parts are scanned and compared.
The briefCredit · unclaimed02
Free CAM tested on molds
A public scorecard of free CAM programs on mold work. Program the same ten mold inserts in FreeCAD's CAM workbench, in Fabex (formerly BlenderCAM) and in Kiri:Moto, and in one commercial CAM program as a baseline. Simulate every program, cut three inserts in machining wax, and then contribute a fix for the largest gap found to one of the free projects.
The briefCredit · unclaimed
Open 01 · the brief
AI against a mold programmer
The first to publish is credited on this line, and the deliverable moves from Open to Achieved.
What to build
A public comparison on ten mold insert test parts, each with a freeform face, deep ribs and small inside corners. Each part is programmed twice, once by an AI CAM tool or AI agent and once by an experienced mold programmer. Both programs are cut on the same machine in machining wax or aluminum, and the parts are scanned and compared.
Why it is still open
Published tests of AI-written machine programs use simple shapes or prismatic parts, not the freeform faces of a mold. GLLM, a fine-tuned language model from January 2025, was tested on flat shapes such as a circle cut 2 mm deep. CloudNC said in 2023 that its CAM Assist works best on three-axis parts, with freeform machining still to come for beta users. In October 2026 Cimatron's CAM Agent was in beta with no efficiency data. No independent comparison on mold work was found.
Built with what exists
CloudNC CAM Assist in Autodesk Fusion, Cimatron's CAM Agent where available, or an AI coding agent writing scripts for FreeCAD's CAM workbench; a small enclosed desktop CNC mill such as a Bantam Tools or Makera Carvera machine; machining wax; a structured-light 3D scanner and a surface roughness tester.
First step
Design three test inserts with a rib 10 mm deep and 1.5 mm wide, a 1 mm inside radius and a freeform face, and program one by hand.
Done looks like
Ten parts, each cut from both programs, with a published table of programming time, machining time, largest deviation from the CAD model in mm and surface roughness, plus the programs and scans.
Open 02 · the brief
Free CAM tested on molds
The first to publish is credited on this line, and the deliverable moves from Open to Achieved.
What to build
A public scorecard of free CAM programs on mold work. Program the same ten mold inserts in FreeCAD's CAM workbench, in Fabex (formerly BlenderCAM) and in Kiri:Moto, and in one commercial CAM program as a baseline. Simulate every program, cut three inserts in machining wax, and then contribute a fix for the largest gap found to one of the free projects.
Why it is still open
The free programs offer 3D finishing, but none has been measured on molds. Fabex lists parallel, cross, spiral and other 3D strategies. In FreeCAD's current source code, the 3D Surface and Waterline finishing operations appear only when a user switches on "advanced OCL features", which are off by default, and they need the separate OpenCamLib library. No published comparison of free and commercial CAM on mold surfaces was found; buyer's guides give only general statements.
Built with what exists
FreeCAD with OpenCamLib; Fabex, which runs inside Blender; Kiri:Moto, which runs in a web browser; CAMotics, an open-source cutting simulator; Autodesk Fusion under a personal or education license as the commercial baseline; a small enclosed desktop CNC mill and machining wax; an AI coding agent to script the runs and write the fix.
First step
Program one insert with a freeform face in the three free programs, simulate each in CAMotics, and publish the results side by side.
Done looks like
Ten inserts programmed in all four programs, with a published table of simulated machining time, largest deviation from the model in mm, scallop height (the ridges a ball cutter leaves between passes) and any gouges; three inserts cut and scanned for each program; and one fix accepted into a free project.