BRENNEN

Industries / Industrial equipment and services / Industrial services / Industrial cleaning / Tank cleaning

Robots and cleaning without entry

This work takes people out of the tank: a machine goes in through a manway or roof opening and is driven, or watched, from outside while it breaks up the sludge and sends it out through a hose.

4

Milestones achieved, from 1996 to 2002.

2

To watch for: announced, not yet confirmed outside.

2

Open deliverables. Nobody has shipped them.

The road

AchievedWatch forOpen

Achieved

  1. 1996

    A robot drives in

    Kenneth C. Landry and Paul Borg of League City, Texas, were granted a US patent, filed in 1994, on a remotely controlled tracked vehicle for refinery storage tanks. It sprays water or heated diluent at the sludge and sucks up the slurry, while an operator in a climate-controlled cabin outside steers it by camera and watches its readings of hydrogen sulfide, oxygen and flammable gas. Its tracks were bronze plates covered with hard rubber so they would not spark, and the operator was warned if the vehicle lost its grounding against static. The patent says earlier methods needed someone inside the tank in sight of the nozzle.

    patentimages.storage.googleapis.com

    Credit

    Kenneth C. Landry and Paul Borg

  2. 1997

    Robots go into radioactive tanks

    Oak Ridge National Laboratory in Tennessee had old underground concrete tanks, 20 to 50 ft across, with a heel of radioactive sludge up to 3 ft deep and no opening wider than 30 in. Houdini, a hydraulic tracked vehicle built by RedZone Robotics from a concept Carnegie Mellon University proposed in 1992, folds to pass through a 24 in. opening and then spreads into a small bulldozer with a plow blade and an arm. It first went into the tanks in June 1997 and, by the US Department of Energy's account, played a key role in cleaning three of them. The department's report says its advantages over sending people in were not measured, because sending workers in to compare would have been too dangerous, and it lists the first unit's faults: maintenance was harder and more frequent than wanted, the vehicle was not always centred under the opening, and its storage box was too small.

    LessonA tank robot needs practised operators and easy maintenance as much as reach; the report calls practice in cold tests critical, because inexperienced operators can easily damage the machine.

    osti.govdndkm.org

    Credit

    RedZone Robotics; Carnegie Mellon University; Oak Ridge National Laboratory; US Department of Energy

  3. 1997

    Desludged while in service

    At BP's Alliance refinery at Belle Chasse, Louisiana, tank 15A, a 280 ft floating-roof tank in the wastewater plant, had built up about 12 ft of sludge but could not be taken out of service, because its space was needed in heavy rain. In 1997 Landry Service Co. (Lansco) mounted its remote-controlled tank-entry device on the roof, jetted recycled water into the sludge to push it toward the drains, and sent the slurry to centrifuges outside. Working around the clock for three months, it brought the sludge down to about 1 ft, with nobody entering the tank. Over two years on this tank and a sister tank, about 950 tons of solids and 5,714 bbl of oil were recovered, by the account of two BP engineers and a Lansco manager.

    ogj.com

    Credit

    Lansco; Alan Stobbe and Randy Borne of BP's Alliance refinery

  4. 2002

    Zone 0 needs special machines

    Britain's Dangerous Substances and Explosive Atmospheres Regulations 2002, in force from 9 December 2002, define zone 0 as a place where a flammable mixture of gas, vapor or mist with air is present continuously, for long periods or frequently, and allow only category 1 equipment there, the strictest class of explosion protection. Robots for oil tanks are built to that level: Re-Gen Robotics describes its robots as Zone 0 certified, and Gerotto of Italy, whose products are ATEX Zone 0 certified for Europe, said in October 2025 that it had gained an IECEx certificate, the international scheme, with the testing body TÜV SÜD. Gerotto had said in January 2024 that it expected that certificate by mid-2024.

    LessonCertifying a machine to work inside a tank can take far longer than its maker plans; Gerotto's IECEx certificate came about 21 months after it announced the process, well over a year after the date it first gave.

    legislation.gov.uklegislation.gov.uklegislation.gov.ukregenrobotics.comtankstorage.comtankstorage.com

    Credit

    UK Dangerous Substances and Explosive Atmospheres Regulations 2002

Watch for

  1. Cameras that log tank work

    Gerotto says its new G-OPTICAM cameras, certified for zone 0, connect to an AI system that watches events and scans the work area in real time. Users can ask it questions in several languages, pull up near-miss events and have it write reports on tasks and equipment performance, and the company says it is training algorithms in its own data room toward robots that work on their own.

    Achieved whena tank owner or contractor outside Gerotto publishes how the system did on real jobs, for example the share of near-miss events it caught compared with a person reviewing the same video.

    tankstorage.com

    Claimed by

    Gerotto, at the IFAT trade fair in Munich, April 2026

  2. Robot for buried fuel tanks

    GRP Plasticorr, a Hungarian tank services company, chose Gerotto's Lombrico FTC robot for an underground tank cleaning project in Hungary. The robot weighs less than 130 kg, is ATEX Zone 0 rated, enters through a manhole as small as 400 mm, and washes with three rotating nozzles at 5 to 200 bar. The announcement says it cuts cleaning time from 1.5 hours to 1 hour and removes the need for anyone to enter the tank, and Gerotto counts more than 6 million underground tanks at service stations worldwide.

    Achieved whenGRP or a tank owner publishes the number of tanks cleaned, the time each took and the residue left, with no person entering any of them.

    tankstorage.comtankstorage.com

    Claimed by

    Gerotto Robotics and GRP Plasticorr, July 2026

Open

  1. 01

    Show what is left behind

    Software that takes a desludging robot's camera and a small scanning sonar and keeps a running map of the tank floor, showing where sludge remains and how deep, then ends each job with a residue map and an estimate of the volume left. An owner outside the tank could use it to decide whether the floor is clean enough for inspection. It would be tested on a mock floor in a workshop: a shallow steel pan under water, with a stand-in sludge, mock heating coils and roof legs. No real tank, no oil, and no one inside anything.

    The brief
    Credit · unclaimed
  2. 02

    Test course for tank robots

    A standard mock tank floor and test method on which any desludging robot can be scored the same way, modelled on the test methods the US National Institute of Standards and Technology (NIST) wrote for emergency response robots. The robot passes a 600 mm manway, works round rows of heating coils and roof legs, clears a sump and removes a weighed load of stand-in sludge. It is scored on kilograms removed per hour, share removed, time stuck and the number of times the operator had to step in.

    The brief
    Credit · unclaimed

Open 01 · the brief

Show what is left behind

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

Software that takes a desludging robot's camera and a small scanning sonar and keeps a running map of the tank floor, showing where sludge remains and how deep, then ends each job with a residue map and an estimate of the volume left. An owner outside the tank could use it to decide whether the floor is clean enough for inspection. It would be tested on a mock floor in a workshop: a shallow steel pan under water, with a stand-in sludge, mock heating coils and roof legs. No real tank, no oil, and no one inside anything.

Why it is still open

How much sludge a tank holds is often unknown until it is out: Re-Gen Robotics says the Phillips 66 tank was thought to hold about 135 t of waste, and 536 t was removed. Robots in service send video to an operator; Gerotto's newest system logs events and writes reports but gives no measure of residue; Genrobotics' Draco, still a scaled prototype, joins sonar and cameras to map the floor for navigation; and the Department of Energy did not measure Houdini's results against any alternative. No tool was found that maps the sludge remaining during a no-entry clean and is checked against a weighed amount.

res.cloudinary.comtankstorage.comresearch.genrobotics.comosti.gov

Built with what exists

Blue Robotics' Ping360 scanning sonar, sold for small underwater robots; a stereo depth camera such as Luxonis' OAK-D; Open3D, an open library for building 3D maps; Meta's Segment Anything Model 2 to mark sludge in camera images; ROS 2 to tie the parts together; a hobby-scale tracked chassis as the carrier. Mapping a room with a cheap camera on wheels is now sold to households (see the Note "A camera on patrol").

  1. First step

    Lay a measured layer of stand-in under water in a pan, scan it with a Ping360 from a fixed mount, and compare the sonar's depths with ruler readings at 25 points.

  2. Done looks like

    In 20 runs on a 2 m by 2 m mock floor with known amounts of stand-in, the map's estimate of the remaining volume is within 10% of the weighed remainder, and no patch it calls clean holds more than 5 mm of stand-in; code, maps and photos published.

Open 02 · the brief

Test course for tank robots

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

A standard mock tank floor and test method on which any desludging robot can be scored the same way, modelled on the test methods the US National Institute of Standards and Technology (NIST) wrote for emergency response robots. The robot passes a 600 mm manway, works round rows of heating coils and roof legs, clears a sump and removes a weighed load of stand-in sludge. It is scored on kilograms removed per hour, share removed, time stuck and the number of times the operator had to step in.

Why it is still open

The published figures for robot jobs come from the robot's own operator, each measured against a different baseline. Re-Gen Robotics compares its 43 days at Phillips 66 with an estimate of 95 days for six people cleaning by hand; Essar Oil heard a vendor claim a 50% cut in time; and the Department of Energy did not measure Houdini against an alternative. NIST's methods let buyers compare emergency response robots on the same tests; no such shared test was found for tank cleaning robots.

res.cloudinary.comafpm.orgnist.gov

Built with what exists

NIST's published response robot test designs as a model; a plywood and steel mock floor with pipe coils and legs; the stand-in sludge (see "A stand-in sludge recipe" under Removing sludge); platform scales; overhead cameras; a public results table on GitHub.

  1. First step

    Write the course layout from published tank dimensions (600 mm manways, coil and leg spacing) and build a 3 m by 3 m section.

  2. Done looks like

    Course plans and scoring rules published; at least two robots of different designs, which may be university or hobby builds, run ten trials each with results, video and raw data public; a second group builds the course from the plans and scores the same robot within 15% of the first.