BRENNEN

Industries / Industrial equipment and services / Industrial services / Industrial cleaning / Tank cleaning

Treating the waste

This work decides what happens to what a tank cleaning takes out, the sludge of oil, water and solids and the oily wash water: how the law classes it, and whether its oil is recovered and the rest treated, burned or buried.

4

Milestones achieved, from 1998 to 2021.

1

To watch for: announced, not yet confirmed outside.

2

Open deliverables. Nobody has shipped them.

The road

AchievedWatch forOpen

Achieved

  1. 1998

    Microbes clear a sludge dump

    At the Mathura refinery in India, 150 km south of Delhi, researchers spread oil-eating bacteria grown on a carrier, with nutrients, over a 1 ha patch of an old dumping ground for crude tank sludge and other refinery sludges, from January to December 1998. Total petroleum hydrocarbons (TPH, the usual measure of oil in soil) fell by 92.0% and 89.7% in the two treated plots in a year, against 14.0% in an untreated plot. The institute sells the bacteria as Oilzapper through ONGC TERI Biotech. Bharat Petroleum, a refiner outside the study, reports that it was applied at Mathura over about three acres and at the Barauni refinery; the institute's own count is over 1.3 million tonnes of contaminated soil treated.

    pmc.ncbi.nlm.nih.govbharatpetroleum.interiin.org

    Credit

    Sanjeet Mishra, Jeevan Jyot, Ramesh C. Kuhad and Banwari Lal, Tata Energy Research Institute (now The Energy and Resources Institute, TERI) and the University of Delhi South Campus

  2. 2000

    Europe codes tank sludge

    The European Commission's list of wastes, adopted on 3 May 2000 in Decision 2000/532/EC, gives "tank bottom sludges" from petroleum refining the code 05 01 03 with an asterisk, the mark of a hazardous waste. The decision replaced the separate lists of wastes and of hazardous wastes adopted in 1994.

    legislation.gov.uk

    Credit

    European Commission

  3. 2006

    Refinery sludge fuels kilns

    In 2005 and 2006 cement plants in India ran five trial burns of wastes as part of their fuel, including refinery sludge, while officials of the Central Pollution Control Board (CPCB), the national regulator, monitored clinker quality and stack emissions of metals, acid gases, dioxins and furans, dust, sulphur dioxide and nitrogen oxides. In the first six trials of the programme no significant exceedances or rises over normal emissions were found, except nitrogen oxides in one trial. The white papers based their proposed emission standards for burning waste in cement kilns, a route called co-processing, on these results.

    c2e2.unepccc.org

    Credit

    Central Pollution Control Board; reported in white papers of India's Forum of Regulators and the Institute for Industrial Productivity

  4. 2021

    China lists the wash water

    China's National Catalogue of Hazardous Wastes, 2021 edition, in force from 1 January 2021, lists under waste mineral oil (HW08) the oil and water mixtures produced in cleaning mineral oil storage and transport facilities, oily sludge from storage facilities in primary refining, sludge from oil production and from storage at oilfield gathering stations, and sludge from storing fuel oil. In China both the sludge and the water used to wash a tank out are hazardous waste.

    mee.gov.cn

    Credit

    Ministry of Ecology and Environment, with four other ministries (Order No. 15)

Watch for

  1. Sound waves free tank oil

    In bench tests on 2.2 kg samples of crude oil tank bottoms from three California oilfields, mixed one part sludge to four parts water in an acrylic tank with two 500 W plate sonicators (devices that send sound above human hearing through the water) at 28 or 40 kHz and no chemicals, Arizona State University recovered up to 98.2% of the oil, with a mean of 27.4%, using 0.2 kWh per kg of sample. The authors say most earlier sonication tests used samples under 100 g, and that energy use at larger scale is unknown. Chevron funded the work and two of its staff are co-authors.

    Achieved whena test on at least 200 kg of tank bottoms, run or checked by a party outside the authors and their funder, reports oil recovered as a share of the oil in the feed and energy per kilogram.

    doi.orgmdpi-res.com

    Claimed by

    Paul Dahlen and co-authors, Arizona State University and Chevron, in the journal Waste, April 2026

Open

  1. 01

    One number for oil content

    An interlaboratory test, in which several labs measure the oil, water and solids in the same samples of a stand-in tank sludge whose oil content is known because it was weighed in: sand, kaolin clay, water and a mineral base oil thickened with paraffin wax. Each lab uses the methods in use today: azeotropic distillation (boiling the water off with a solvent and collecting it in a Dean-Stark trap), solvent extraction and weighing, infrared and ultraviolet absorbance, and heating in a thermogravimetric analyzer, which weighs a sample as it is heated. The spread between labs and between methods is published. Treatment results, cleaning contracts and disposal limits all turn on this one number.

    The brief
    Credit · unclaimed
  2. 02

    Sonication at drum scale

    An open sonication rig the size of a 200-litre drum, holding about 40 kg of stand-in tank sludge (sand, clay, water and a waxy heavy mineral oil) in 160 litres of water, which measures oil recovered and electricity used per kilogram at about 18 times the sample size of the largest chemical-free sonication test published. Every run is logged and published, with drawings, so others can build the same rig. It uses no real tank waste, so it shows how energy use and recovery change with scale, not how a given tank's sludge will behave; that needs a licensed laboratory.

    The brief
    Credit · unclaimed

Open 01 · the brief

One number for oil content

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

An interlaboratory test, in which several labs measure the oil, water and solids in the same samples of a stand-in tank sludge whose oil content is known because it was weighed in: sand, kaolin clay, water and a mineral base oil thickened with paraffin wax. Each lab uses the methods in use today: azeotropic distillation (boiling the water off with a solvent and collecting it in a Dean-Stark trap), solvent extraction and weighing, infrared and ultraviolet absorbance, and heating in a thermogravimetric analyzer, which weighs a sample as it is heated. The spread between labs and between methods is published. Treatment results, cleaning contracts and disposal limits all turn on this one number.

Why it is still open

Li, Wang and Zhu (2023) measured the same two sludges by distillation and by ultraviolet absorbance and got 56.96% against 14.78% oil for one and 7.62% against 3.16% for the other. A 2022 study of sludge from China's Shengli oilfield measured its oil with China's standard method for oilseed meal (GB/T 10359-2008). Searches of Crossref, a free index of papers, for an interlaboratory study of oil in sludge found none.

doi.orgpmc.ncbi.nlm.nih.gov

Built with what exists

Dean-Stark distillation glassware; benchtop infrared oil analyzers; an ultraviolet-visible spectrophotometer; a thermogravimetric analyzer, found in most university materials labs; a precision balance to weigh in the oil; R or Python to compute each method's repeatability, reproducibility and bias.

  1. First step

    Make the five samples in one batch, split them, and have two university labs measure each by distillation and by infrared.

  2. Done looks like

    At least eight labs on at least three continents measure five stand-in samples from 2% to 60% oil by weight, each by at least two methods; each method's bias from the weighed-in value and the spread between labs are published, with the recipe so anyone can make the samples again.

Open 02 · the brief

Sonication at drum scale

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

An open sonication rig the size of a 200-litre drum, holding about 40 kg of stand-in tank sludge (sand, clay, water and a waxy heavy mineral oil) in 160 litres of water, which measures oil recovered and electricity used per kilogram at about 18 times the sample size of the largest chemical-free sonication test published. Every run is logged and published, with drawings, so others can build the same rig. It uses no real tank waste, so it shows how energy use and recovery change with scale, not how a given tank's sludge will behave; that needs a licensed laboratory.

Why it is still open

Dahlen and co-authors (2026) found that, apart from one 7,500-gallon pilot that used added chemicals, published sonication tests on oily sludge used samples under 100 g; their own 2.2 kg tests averaged 27.4% oil recovery, and they write that energy efficiency at larger scales is unknown.

mdpi-res.com

Built with what exists

Immersible ultrasonic transducer plates sold for industrial parts cleaning, at 28 kHz and 40 kHz as in the 2026 study; a drum mixer and a surface skimmer; a plug-in power meter; Dean-Stark analysis of the feed, the recovered oil and the leftover solids; Python for the run log.

  1. First step

    Build a 20-litre version with two 500 W plates, the size used in the 2026 study, and check that it gives recoveries in the study's range on the stand-in sludge.

  2. Done looks like

    30 runs across two frequencies and three treatment times, each reporting oil recovered as a share of the oil in the feed, energy in kWh per kg, and oil left in the solids as measured by a lab not involved in the build; data, code and drawings published under an open licence.