BRENNEN

Industries / Industrial equipment and services / Robotics

Parts and motors

Parts and motors are what goes inside each joint and at the end of the arm: the motors, the reduction gears that trade speed for turning force, the sensors that measure angle and force, the drive electronics, and the grippers that hold the work.

6

Milestones achieved, from 1959 to 2025.

3

To watch for: announced, not yet confirmed outside.

2

Open deliverables. Nobody has shipped them.

The road

AchievedWatch forOpen

Achieved

  1. 1959

    Gears that flex

    C. Walton Musser filed a patent for "strain wave gearing" on 21 March 1955, granted as US patent 2,906,143 on 29 September 1959. Instead of making gears ever stiffer, the idea uses the flexibility of metal: in the patent an elliptical "strain inducer" bends a thin toothed ring into an oval, so that it meshes with a rigid ring gear with, by preference, two more teeth and creeps round it, giving a large speed reduction in a small space. United Shoe Machinery in the United States and Hasegawa Gear Works in Japan, the forerunners of Harmonic Drive LLC and Harmonic Drive Systems, took it to market. Robot arms use it: the German Aerospace Center (DLR) names Harmonic Drive gears as one key to its Light Weight Robot III lifting as much as it weighs.

    patentimages.storage.googleapis.comharmonicdrive.netdlr.de

    Credit

    C. Walton Musser; United Shoe Machinery; Hasegawa Gear Works

  2. 1982

    AC servo motors arrive

    A servo motor is a motor run with a position sensor and a controller so that it turns to a commanded angle and holds it. FANUC, the Japanese maker, began making DC servo motors under licence from Gettys Manufacturing in 1974 and developed its own AC servo motor in 1982. ABB says its IRB 2000 arm of 1986 was the first of its arms whose motors were "powered by AC."

    fanuc.co.jplibrary.e.abb.com

    Credit

    FANUC; ABB

  3. 1985

    A cycloidal gear for robots

    In a cycloidal gear, a lobed disc rolls around inside a ring of pins, which makes a stiff, compact speed reducer. Nabtesco says it built its first cycloidal gearbox in 1980 for excavator drives, developed precision gears in autumn 1983 at the request of Japan's robot makers, and launched the RV ("rotor vector") gearbox in 1985. It describes itself as the "Number 1 supplier for robotics (60% market share in industrial robotics sector)"; that share is Nabtesco's own figure.

    nabtesco.de

    Credit

    Nabtesco

  4. 2006

    Torque sensors in every joint

    The German Aerospace Center (DLR) presented its Light Weight Robot III in 2003: a seven-joint arm of 14 kg that can handle 14 kg and is "completely torque controlled," meaning each joint senses and controls its turning force. The IFR says KUKA presented its first Light Weight Robot, developed with DLR, in 2006, with a 7 kg payload and a weight of 16 kg. KUKA says its LBR iiwa of 2013 was "the world's first series-produced sensitive robot approved for direct human-robot collaboration."

    dlr.deifr.orgkuka.com

    Credit

    DLR Institute of Robotics and Mechatronics; KUKA

  5. 2015

    Soft fingers, then a sale

    Soft Robotics grew out of work in George Whitesides' group at Harvard University and from late 2015 sold grippers with rubbery fingers driven by air pressure, fitted to other makers' arms; in 2017 it said about 80% of its business was in food. In August 2024 it sold its gripper business to J. Schmalz, a German maker, and moved its 3D vision and AI work into a new company, Oxipital AI. Its chief executive, Mark Chiappetta, called grippers "a niche business" and said, "Without focus, it's difficult to survive."

    LessonNearly 1,000 soft grippers in the field did not make the gripper alone a business its maker wanted to keep.

    techcrunch.comtherobotreport.com

    Credit

    Soft Robotics; J. Schmalz

  6. 2025

    Magnets become a choke point

    In April 2025 China tightened export controls on seven rare-earth metals and required export licences for rare-earth magnets, which go into the compact motors of robot joints. On Tesla's earnings call that month Elon Musk said production of Tesla's Optimus humanoid robot was affected by the "magnet issue" and that Tesla was seeking a licence. Fortune reported that Optimus's arm motors need these magnets to work without overheating in a small space, and cited a 2023 Aspen Institute figure of about 92% of world rare-earth magnet production in China.

    LessonThe motor in a joint depends on a magnet supply concentrated in one country, and a licence rule there can slow a robot line elsewhere.

    fortune.com

    Credit

    Government of China (controls); Tesla (reported effect)

Watch for

  1. Maintenance models in the joint

    MIPS, a GlobalFoundries business, says its Actus platform, a single chip design for compact robot joints built on two Atlas M8500 RISC-V processor cores, can run models that predict when maintenance is due "on the same chip that drives the motor," and claims "more than 16x the performance of standard trigonometric libraries" for the motor-control maths. MIPS names no test setup, gives no loop times and no sample date; software can start on a virtual platform and an Actus-1 evaluation board. See the Note "Maintenance inside the joint."

    Achieved whenA joint or robot maker ships joints built on Actus, or an outside party publishes measured loop times and maintenance-prediction results.

    mips.com

    Claimed by

    MIPS, November 2026

  2. Small GaN drivers for joints

    STMicroelectronics says its GANSPIN1102 and GANSPIN1105, half-bridges (pairs of power switches) made of gallium nitride and rated for 100 V input, fit in a 6.5 mm by 5 mm package with on-resistances of 2.4 and 5.5 milliohms and maximum currents of 60 A and 29 A, and names humanoid joints as the target. Its community announcement says the devices "will be available by the end of 2026, priced from $1.65 for orders of 1000 pieces." See the Note "A half-bridge in 6.5 by 5 mm."

    Achieved whenThe parts can be bought from distributors and a joint maker or outside lab publishes measured temperatures and efficiency in a working joint.

    blog.st.comcommunity.st.com

    Claimed by

    STMicroelectronics, November 2026

  3. Schaeffler's humanoid joint actuators

    Schaeffler, a German maker of bearings and drive parts, says its rotary actuator platform for humanoid joints, with bearings built into the motor's rotor, cuts installation space by about 20% and weight by up to 500 g, and estimates that actuators make up about 50% of a humanoid's bill of materials. The platform won the Hermes Award, chosen by an independent jury at Hannover Messe on 19 April 2026; Schaeffler gave no production volumes or customers.

    Achieved whenA humanoid maker reports Schaeffler actuators in robots in routine work, or an outside test confirms the space and weight figures.

    machinedesign.com

    Claimed by

    Schaeffler, April 2026

Open

  1. 01

    Check joint module torque claims

    An independent bench test of joint modules sold for legged and humanoid robots, each a motor, gearbox, angle sensor and driver in one housing. For each, measure peak torque (turning force), the torque it holds for 10 minutes before passing a set temperature, backlash (free play at the output) and the whole module's mass, and set them beside the maker's figures.

    The brief
    Credit · unclaimed
  2. 02

    Run hobby servos to failure

    An open wear test that runs the small servo motors used in low-cost learning arms until they fail, under fixed loads, logging position error, backlash, current and temperature throughout. The log becomes a public dataset on which anyone can test whether a coming failure shows in current and temperature first.

    The brief
    Credit · unclaimed

Open 01 · the brief

Check joint module torque claims

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

An independent bench test of joint modules sold for legged and humanoid robots, each a motor, gearbox, angle sensor and driver in one housing. For each, measure peak torque (turning force), the torque it holds for 10 minutes before passing a set temperature, backlash (free play at the output) and the whole module's mass, and set them beside the maker's figures.

Why it is still open

Makers quote torque density, turning force per kilogram, on different mass bases. A buyer's guide notes that "figures use each source's own definition," and treats Unitree's 189 N·m/kg for one joint motor as a vendor claim with no stated mass. Searches found makers testing their own actuators but no independent comparison, and Humanoid.guide's August 2026 report on how humanoid joints are tested names test-bench makers and a proposed test method, but no published comparison of several makers' modules.

humanoid.guidehumanoid.guide

Built with what exists

Five joint modules with peak torque under 25 N·m, such as the CubeMars AK80-9 (by its maker, 9 N·m rated and 22 N·m peak in 485 g); a bench vise and a steel lever pressing on an S-type load cell read by an HX711 amplifier; a thermocouple on the housing; a bench power supply with a current limit; a 1 g scale.

  1. First step

    Buy one module, build the lever and load-cell rig, and measure its peak and 10-minute torque.

  2. Done looks like

    Five module models, two units each, with measured peak torque, 10-minute torque at a stated temperature rise, backlash in arcminutes and mass, published beside each maker's numbers as a percentage difference, with the raw logs.

Open 02 · the brief

Run hobby servos to failure

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

An open wear test that runs the small servo motors used in low-cost learning arms until they fail, under fixed loads, logging position error, backlash, current and temperature throughout. The log becomes a public dataset on which anyone can test whether a coming failure shows in current and temperature first.

Why it is still open

Robonine measured one Feetech STS3215 at about 0.87° of backlash, above the 0.5° in its datasheet, and logged its heating, but lists long-term wear testing as a limitation and reports none. In August 2026 an SO-101 owner on a hobby robotics mailing list reported stripped gears and three burned-out servos. No run-to-failure data for these servos turned up. Chip makers now promise maintenance prediction inside joints (see the Note "Maintenance inside the joint") without public failure data to test it on.

robonine.comgroups.google.com

Built with what exists

Twenty Feetech STS3215 servos on printed levers with hanging weights; a Raspberry Pi or PC reading each servo's position, load, current and temperature over its serial bus, with Hugging Face's LeRobot software (see the Note "No download"); a dial indicator for weekly backlash checks; a 12 V supply and fans.

  1. First step

    Mount four servos at four loads with a logging script and run them for one week.

  2. Done looks like

    Twenty servos at four load levels run until failure or 1,000 hours, with cycles to failure by load, backlash growth over time and the full log published as an open dataset.