BRENNEN

Industries / Transport and vehicles / Railcar manufacturing

Wheels, bogies and brakes

This is the work of making the running gear under every rail vehicle: the wheels, axles and bearings, the bogie (called a truck in North America) that holds them under the car, the couplers that join cars, and the brakes.

5

Milestones achieved, from 1869 to 2017.

1

To watch for: announced, not yet confirmed outside.

2

Open deliverables. Nobody has shipped them.

The road

AchievedWatch forOpen

Achieved

  1. 1869

    Brakes worked by air

    On 13 April 1869 George Westinghouse Jr. received US patent 88,929 for a brake in which a steam-driven pump filled a reservoir with compressed air, and a pipe along the train carried the air to a cylinder on each car that pushed the brakes on. His patent of 5 March 1872 (US 124,404) added an air receiver under each car, so that the brakes applied by themselves if a car broke away or left the track.

    patents.google.compatents.google.com

    Credit

    George Westinghouse Jr

  2. 1873

    A coupler that latches itself

    On 29 April 1873 Eli H. Janney of Alexandria, Virginia, received US patent 138,405 for a car coupling whose pivoting hook swings back and locks when two cars are pushed together. US law still requires cars to have "couplers coupling automatically by impact" that can be uncoupled without anyone going between the cars, a requirement that traces to the federal act of 2 March 1893.

    patents.google.comlaw.cornell.edu

    Credit

    Eli H. Janney; US Congress

  3. 2014

    A bogie of carbon fiber

    On 14 March 2014 Kumamoto Electric Railway in Japan put a Series 6000 train on Kawasaki's efWING bogies into passenger service, and it added more cars on efWING bogies in 2015 and 2016, by Kawasaki's account. The bogie frame is made of carbon-fiber-reinforced plastic (CFRP), and curved CFRP leaf springs take the place of the steel side frames and coil springs. Kawasaki says the frame weighs about 40% less than a conventional North American bogie frame, about 900 kg less per car, and that the bogie met US running-safety requirements in tests at the Transportation Technology Center in Colorado.

    global.kawasaki.com

    Credit

    Kawasaki Heavy Industries; Kumamoto Electric Railway

  4. 2015

    Electronic brakes ordered, then dropped

    In May 2015 US regulators required trains of 70 or more loaded tank cars of flammable liquid, under certain conditions, to have electronically controlled pneumatic (ECP) brakes, in which an electric signal, not a fall in air pressure, tells every car's brakes to apply. Congress then ordered a new cost-benefit test. In 2016 the Government Accountability Office (GAO) found that DOT's modeling "lacked transparency" and might not let a third party replicate it. In December 2017 DOT found that the expected benefits "do not exceed the associated costs", and in September 2018 PHMSA removed the requirement.

    LessonA rule that orders new equipment needs a cost case that outsiders can check.

    govinfo.govgao.gov

    Credit

    PHMSA and FRA (US Department of Transportation); GAO

  5. 2017

    A frame ground too thin

    On 11 December 2017 a crack was found in a bogie frame of a JR West N700 Shinkansen train at Nagoya Station. Kawasaki, which made the frame in February 2007, found that the bottom plate of its side frame, designed at 8 mm and to be no thinner than 7 mm after machining, had been ground down to 4.7 mm at its thinnest so that the spring seats would fit during welding. Its September 2018 report blamed relying on the "discretions or judgments" of the shop floor "in excessive manner" and poor risk management when the supplier that pressed the side frames changed in 2006. Kawasaki now inspects, on the first unit of each design, areas that cannot be seen once a frame is finished.

    LessonA fault that later work covers up cannot be found by inspecting the finished part.

    global.kawasaki.com

    Credit

    Kawasaki Heavy Industries (report); JR West

Watch for

  1. Digital couplers for European freight

    Europe's rail research program is testing a digital automatic coupler (DAC) to replace the screw couplers on European freight wagons. In June 2026 it reported that a DB Cargo locomotive fitted with hybrid couplers from Dellner and Voith, which can join to both old and new couplers, had been "successfully" tested at a test lab in Berlin, without publishing figures. In July 2026 Rail Cargo Group described nearly 100 derailment and pushing tests in Görlitz in 2025 against a target of 550 kN (up from 240 kN), climate-chamber tests from about −25 °C to +40 °C, and crash tests planned for autumn 2026.

    Achieved whenwagons with the chosen coupler run in regular freight service in more than one country, or the test results are published for others to check.

    rail-research.europa.eurailcargo.com

    Claimed by

    Europe's Rail Joint Undertaking (project FP5-TRANS4M-R), DB Cargo and Rail Cargo Group, June and July 2026

Open

  1. 01

    Thickness check after grinding

    A test station where a robot arm carries an ultrasonic thickness probe over welded steel box sections shaped like bogie side frames, after a fabricator has ground them to fit, and maps the plate thickness everywhere grinding was done. It flags every spot thinner than the drawing allows. Some test pieces are ground below the minimum on purpose.

    The brief
    Credit · unclaimed
  2. 02

    Rerun the ECP brake case

    An open copy of the computer modeling and cost-benefit analysis the US DOT used to judge ECP brakes for tank-car trains: code that reproduces DOT's published results, then reruns them with derailments since 2017, with every input in one table.

    The brief
    Credit · unclaimed

Open 01 · the brief

Thickness check after grinding

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

A test station where a robot arm carries an ultrasonic thickness probe over welded steel box sections shaped like bogie side frames, after a fabricator has ground them to fit, and maps the plate thickness everywhere grinding was done. It flags every spot thinner than the drawing allows. Some test pieces are ground below the minimum on purpose.

Why it is still open

At Kawasaki, a bogie frame plate designed at 8 mm was ground to 4.7 mm and ran for ten years before it cracked. Kawasaki's fix was to add hidden areas to its inspection of the first unit of each design, not to measure every frame. Robot-carried ultrasonic thickness scanning exists for other parts, such as a 2021 system for rocket tank walls with a maximum error of 0.035 mm, but this research found no published test of it on welded bogie frames.

global.kawasaki.comms.copernicus.org

Built with what exists

A collaborative robot arm such as a Universal Robots UR10e; an ultrasonic thickness gauge with a data output, such as the Evident 38DL PLUS; a laser line profiler such as a Keyence LJ-X8000 to find the ground areas; AI agents that write and test the robot's scan paths as readable programs (see the Note "Readable robot programs").

  1. First step

    Have a fabrication shop weld and grind three box sections from 8 mm plate, and map one by hand with a thickness gauge on a 20 mm grid.

  2. Done looks like

    30 test sections with 300 marked spots, each spot later measured with a micrometer after the section is cut open, and a published table of how many below-minimum spots the station found and missed, its error in millimeters and its minutes per section.

Open 02 · the brief

Rerun the ECP brake case

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

An open copy of the computer modeling and cost-benefit analysis the US DOT used to judge ECP brakes for tank-car trains: code that reproduces DOT's published results, then reruns them with derailments since 2017, with every input in one table.

Why it is still open

GAO found in 2016 that what DOT published "may not be sufficient to enable an independent third party to replicate" its modeling. DOT later published its inputs, but removed the requirement in 2018, and GAO closed its call for railroads' ECP data as not implemented. The National Academies reviewed DOT's plan for analyzing and testing ECP brakes in 2017, a review of the plan rather than a rerun of the model. This research found DOT's and the railroads' own analyses, and Chinese work on ECP brakes in heavy-haul trains, but no independent rerun of DOT's model.

gao.govnationalacademies.orggovinfo.gov

Built with what exists

DOT's 2017 updated modeling report and revised regulatory impact analysis (docket PHMSA-2017-0102 on regulations.gov); the FRA's public accident data; Python and an open train-dynamics simulator such as heavyHaulTrainSimulator on GitHub; AI models that pull inputs out of long reports (see the Note "The jobs agents repeat").

  1. First step

    Download the 2017 modeling report and the revised analysis from the docket and list every input in a spreadsheet.

  2. Done looks like

    DOT's published costs and benefits for its three scenarios reproduced within 5%, the code and inputs released under an open license, and a table showing which inputs, if changed, would reverse the result.