Industries / Transport and vehicles / Railcar manufacturing
Locomotives and traction
This is the work of building new locomotives and the traction systems of powered trains: the engines, batteries or overhead-wire equipment that supply power, and the inverters and motors that turn it into pull at the rails.
5
Milestones achieved, from 1804 to 2025.
1
To watch for: announced, not yet confirmed outside.
2
Open deliverables. Nobody has shipped them.
The road
AchievedWatch forOpen
Achieved
1804
Too heavy for the rails
On 21 February 1804 a steam locomotive that Richard Trevithick built at Samuel Homfray's Penydarren ironworks in Merthyr Tydfil, Wales, hauled ten tons of iron and a large number of passengers about 9 miles down the tramroad to the canal at Abercynon. National Museum Wales calls it "the first authenticated journey in the world by a steam locomotive". The engine was too heavy for the tramroad's rails, by the museum's account, and it ended up driving a forge hammer at the ironworks.
LessonA locomotive is only as useful as the track that can carry its weight.
Credit
Richard Trevithick; Samuel Homfray
1979
Three-phase motors take over
Deutsche Bundesbahn's five Class 120 locomotives, built by Krupp and Brown Boveri in 1979 and 1980, were the first on which German railways tried a simple, low-wear drive with three-phase induction motors fed by power electronics, by the DB Museum's exhibit sheet. The same drive was later used in the ICE high-speed trains. Each locomotive weighed 84 tonnes and produced 5,600 kW.
Credit
Brown Boveri; Krupp; Deutsche Bundesbahn
2008
Tier 4 for new locomotives
In 2008 the US Environmental Protection Agency (EPA) set Tier 4 standards for newly built locomotives, starting in 2015, based on exhaust after-treatment, devices that clean the exhaust after it leaves the engine. EPA estimated that Tier 4 engines would emit 90% less particulate matter and 80% less nitrogen oxides than engines built to the Tier 2 standard.
Credit
US EPA
2015
Silicon carbide in traction
A Mitsubishi Electric traction inverter built with all silicon carbide (SiC) power modules ran in commercial service on an Odakyu Electric Railway 1000 series train near Tokyo. From January to May 2015 Mitsubishi measured 17% less power used for driving, and regenerative braking, which returns energy to the overhead line while slowing, rising from 34.1% to 52.1% of the energy used, for about 40% power savings in total compared with a car on an older GTO-thyristor inverter. These are the maker's own figures.
Credit
Mitsubishi Electric; Odakyu Electric Railway. (see the Note "More chips from a bigger disc")
2025
California drops its rule
In April 2023 the California Air Resources Board (CARB) approved a rule that would have required zero-emission locomotives in the state from 2030 and banned locomotives 23 years or older. CARB needed authorization from the US EPA. With no EPA decision, CARB withdrew its request in January 2025, and in June 2025 its staff asked the board to repeal the rule, saying CARB would not enforce it without authorization.
LessonA state deadline for new kinds of locomotive depends on federal approval, and without it the deadline did not hold.
Credit
CARB
Watch for
India's 9,000 hp locomotives
On 26 May 2025 India's prime minister flagged off the first of 1,200 electric freight locomotives of 9,000 horsepower that Siemens Mobility is building over 11 years at Indian Railways' factory in Dahod, Gujarat, under a contract won in January 2023. Siemens says each can haul 5,800 tonnes at up to 120 km/h and that the project is "entering full production mode"; the prime minister said a locomotive "will roll out every two days".
Achieved whenIndian Railways or an outside party reports how many have been delivered and are running, and the plant's output reaches the stated rate.
Claimed by
Siemens Mobility and the Government of India, May 2025
Open
01
Robot inserts motor coils
A robot cell that picks up form-wound coils, the stiff, pre-shaped copper coils used in large traction motors, and lays them into the slots of a stator, the motor's outer core of stacked steel sheets. Use a short section of stator with the real slot shape and dummy coils, with no power applied. A camera guides each coil into its slot.
The briefCredit · unclaimed02
Register of zero-emission trains
A public register of every battery, hydrogen and fuel-cell locomotive and self-powered train built or converted worldwide, one row per unit, giving the builder, owner and date, and whether it is in service, on trial, stored or scrapped, with a source for each fact and the date it was last checked.
The briefCredit · unclaimed
Open 01 · the brief
Robot inserts motor coils
The first to publish is credited on this line, and the deliverable moves from Open to Achieved.
What to build
A robot cell that picks up form-wound coils, the stiff, pre-shaped copper coils used in large traction motors, and lays them into the slots of a stator, the motor's outer core of stacked steel sheets. Use a short section of stator with the real slot shape and dummy coils, with no power applied. A camera guides each coil into its slot.
Why it is still open
In a 2020 paper, Andreas Mahr and colleagues at FAU Erlangen-Nürnberg describe fitting form coils into the stator cores of large motors as tedious, costly hand work. Their dual-arm robot prototype did "a major portion" of the job, and they named a vision system and machine learning as ways to close the remaining gaps. In 2025 the same FAU group wrote that so few large rail traction motors are made that rigid, fully automated lines do not pay, and studied pre-forming flat coils so that they could later be fitted by machine; it reported no robot that fits them. Searches of Crossref and the web for this brief found no published work that closed the gaps.
Built with what exists
Two collaborative arms such as Universal Robots UR5e; a depth camera such as an Intel RealSense D435; 3D-printed grippers, as the FAU team used; a robot model that learns a task from a few demonstrations, such as NVIDIA GR00T 2 (see the Note "Five demonstrations per task") or Runway Praxis-1 (see the Note "Open robot model weights").
First step
Get the slot drawing of one traction motor from a motor repair shop, 3D-print a six-slot section, and film a person inserting dummy coils.
Done looks like
50 filmed attempts to fill a stator section with coils, with a public table of coils seated fully and without visible damage to their insulation, minutes per coil and every human touch, plus a person doing five for comparison.
Open 02 · the brief
Register of zero-emission trains
The first to publish is credited on this line, and the deliverable moves from Open to Achieved.
What to build
A public register of every battery, hydrogen and fuel-cell locomotive and self-powered train built or converted worldwide, one row per unit, giving the builder, owner and date, and whether it is in service, on trial, stored or scrapped, with a source for each fact and the date it was last checked.
Why it is still open
Public lists count orders, not running units. A Railway News table, updated in March 2026, lists 41 Alstom iLint hydrogen trains as "in service" in Germany, while the operator EVB said that in August 2025 only 4 of its 14 were running because replacement fuel-cell modules had not arrived. Power Systems Research supplies rail production and power-source data to its clients but describes no unit-by-unit service status, and this research found no public register of units.
Built with what exists
A shared spreadsheet or small database; operators' fleet lists, annual reports and press releases; AI models that pull fleet facts out of long documents (see the Note "The jobs agents repeat"); a monthly scheduled agent run that flags changes for a person to confirm.
First step
Build the rows for Lower Saxony's 14 iLint trains from operator statements, and email the operator to confirm each train's status.
Done looks like
At least 300 units from at least 15 countries, every fact sourced and rechecked each quarter, and an outside check of 30 random rows finding at least 95% of them correct.