BRENNEN

Industries / Industrial equipment and services / Industrial services / Painting and abrasive blasting

Blasting

Blasting drives grit, shot or water at steel to strip rust, mill scale and old paint and to roughen the surface so coatings grip. This domain covers the methods, the abrasives and the harm they do to the people who blast.

7

Milestones achieved, from 1988 to 2020.

1

To watch for: announced, not yet confirmed outside.

2

Open deliverables. Nobody has shipped them.

The road

AchievedWatch forOpen

Achieved

  1. 1988

    Helmets that were never tested

    Blasters breathe through a hood or helmet fed with clean air. Reviewing the causes of sandblasters' silicosis, the lung scarring caused by breathing fine quartz dust, two Tulane University researchers found that national standards for respiratory protection during blasting had existed for more than 50 years. Those standards had not kept pace with blasting equipment and gave no realistic estimate of protection at work. Sellers had misused them, assuring buyers that equipment was acceptable "for conditions under which they have never been tested". The authors conclude that this helped expose sandblasters to hazardous levels of silica.

    LessonA helmet's rating is only as good as the test behind it.

    eutils.ncbi.nlm.nih.gov

    Credit

    H. W. Glindmeyer and Y. Y. Hammad, Tulane University School of Medicine, Journal of Occupational Medicine, December 1988

  2. 1990

    Silicosis in Texas pipe yards

    On 29 June 1990 the Centers for Disease Control reported a cluster of silicosis among sandblasters in Texas. A 2024 study examined 46 Texas oilfield pipe sandblasters who had lung biopsies between 1988 and 1995. Their health declined after less than 10 years of dusty work. At first 54% had normal chest X-rays, but 68% of those showed lung inflammation on gallium-67 scans. Workers exposed to recycled blasting sand fell ill younger, after shorter exposure, and declined faster.

    LessonA normal chest X-ray does not clear a blaster, because this fast form of silicosis can be advanced before it shows.

    eutils.ncbi.nlm.nih.goveutils.ncbi.nlm.nih.gov

    Credit

    Centers for Disease Control, Morbidity and Mortality Weekly Report, 1990; J. A. Crawford, J. L. Abraham and colleagues, SUNY Upstate Medical University, American Journal of Industrial Medicine, 2024

  3. 1998

    Substitutes tested against sand

    In 1974 NIOSH, the US federal institute for workplace health research, recommended banning sand with more than 1% silica from abrasive blasting. In 1998 sand was still the most used blasting abrasive in the United States. KTA-Tator of Pittsburgh, working for NIOSH, blasted steel in a partly controlled field trial with sand and seven substitutes: sand with a dust suppressant, coal slag, copper slag, garnet, nickel slag, staurolite and steel grit. It measured 30 health-related agents in the air and in the abrasives. Every substitute cleaned the steel as required and cut respirable quartz sharply. They cost $0.69 to $1.02 per square foot cleaned, against $0.72 for sand, but each had higher levels than sand of at least four of the other agents. Coal slag gave about 4.2 times sand's airborne beryllium, and copper slag and steel grit more than 5 times its arsenic, as geometric means.

    LessonTaking quartz out of the abrasive moved the hazard rather than removing it, and the authors suggested one health standard covering all the hazards of blasting.

    stacks.cdc.goveutils.ncbi.nlm.nih.gov

    Credit

    KTA-Tator, Inc., for NIOSH, project officer Mark Greskevitch, Phase II report, 21 December 1998

  4. 2004

    Brazil bans sand blasting

    Brazil's labor inspection secretariat banned blasting that uses dry or wet sand as the abrasive in Portaria 99 of 19 October 2004, effective 90 days after publication. The order gives its reasons. Sand blasting produces high levels of crystalline silica and many severe cases of silicosis; silica causes cancer; controls had proved inadequate; substitute methods existed; and the states of Rio de Janeiro, Santa Catarina and Paraná had already banned it. Former shipyard workers still carry the disease. In a 2012 study in Rio de Janeiro, 76% of 25 former shipyard sandblasters with silicosis had large opacities on chest X-rays, and 92% had progressive massive fibrosis, the disease's most severe form, on CT scans. Among 16 stone carvers with silicosis the figures were 18.7% and 43.7%.

    LessonA ban stops new exposure, but disease among people already exposed keeps appearing for years.

    guiatrabalhista.com.breutils.ncbi.nlm.nih.gov

    Credit

    Secretaria de Inspeção do Trabalho, Ministry of Labor and Employment, signed by Ruth Beatriz Vasconcelos Vilela; A. J. Lopes and colleagues, Revista Portuguesa de Pneumologia, 2012

  5. 2005

    Old paint, new dust

    From 2002 to 2004 CPWR, a US construction safety research center, measured the air at painters' helmets as they blasted New Jersey Department of Transportation pedestrian bridges. They used coal slag, steel grit or specular hematite, an iron ore abrasive. Coal slag made the most dust. All three exposed the workers to arsenic, cadmium, chromium, lead, manganese and nickel, and to silica, and much of the lead and silica came from the old paint, not the abrasive. Coal slag holding 4 ppm (parts per million) of beryllium gave airborne beryllium of up to 9.5 µg/m³, and averages almost 5 times OSHA's limit then in force of 2 µg/m³.

    LessonWhat comes off the steel matters as much as the abrasive. CPWR also noted that slag makers had begun listing beryllium on safety data sheets, but not whether all of them did.

    elcosh.org

    Credit

    CPWR – The Center for Construction Research and Training; J. D. Meeker, P. Susi and A. Pellegrino, papers of 2005 and 2006

  6. 2017

    Beryllium rule reaches blasters

    The US Occupational Safety and Health Administration (OSHA) issued its beryllium rule on 9 January 2017. It set a limit of 0.2 µg/m³ averaged over 8 hours and 2.0 µg/m³ over 15 minutes, with separate standards for shipyards and for construction, so that blasters, pot tenders and clean-up crews using slag were covered. The rule records that in a survey for the Navy, coal slag made up 68% and copper slag 20% of the abrasive used by 26 US shipyards and boatyards. It notes that slag use had grown as users avoided silica sand. The Abrasive Blasting Manufacturers Alliance argued that the rule would push users back to silica. A 2020 revision removed skin contact as a trigger for protections in those sectors, citing slag's low beryllium content. In 2025 a University of South Florida team found airborne beryllium below the limit at two jobs blasting structural steel but measured it on blasters' skin after they took off their protective equipment.

    LessonEach move away from sand has brought a new hazard and its own rule.

    govinfo.govscirp.org

    Credit

    OSHA, 82 FR 2470; K. Guth, M. Bourgeois and R. Harbison, Occupational Diseases and Environmental Medicine, 2025

  7. 2020

    Rats breathe the substitutes

    At NIOSH's request, the US National Toxicology Program exposed rats by inhalation to blasting sand and four substitutes: coal slag, crushed glass, garnet and specular hematite. In two-week studies hematite and crushed glass harmed the lungs least, and hematite went on to 39-week studies beside sand. The lung was the main target of both, but inflammation and scarring were significantly lower with hematite at some times and doses. The report says sand makes up about 63% of all blasting abrasive used.

    LessonA safer abrasive is not a harmless one.

    ntp.niehs.nih.gov

    Credit

    National Toxicology Program, National Institute of Environmental Health Sciences, Toxicity Report 91, July 2020

Watch for

  1. Laser against blasting in shipyards

    A National Shipbuilding Research Program (NSRP) project is preparing steel at a shipyard with a pulsed laser, with power tools and with abrasive blasting. It will then coat the samples with Navy epoxy and test them for cyclic corrosion and cathodic disbondment, the loss of adhesion around a coating defect on cathodically protected steel. It will compare the methods' production rate, profile and cleanliness. The project's June 2026 briefing says several shipyards now own laser units and that AMPP has released a laser surface preparation guide for steel (SP21511).

    Achieved whenthe final report is published with measured rates, profile, cleanliness and coating test results for each method.

    nsrp.orgnsrp.org

    Claimed by

    Elzly Technology and Newport News Shipbuilding, NSRP project running February 2026 to February 2027 with $200,000, briefed June 2026

Open

  1. 01

    What is in the abrasive

    A public table of abrasives on sale today, each product named. For each, an accredited laboratory analyzes its metals (arsenic, beryllium, cadmium, chromium, lead, manganese and nickel) and its crystalline silica, and the results are set beside what its safety data sheet declares.

    The brief
    Credit · unclaimed
  2. 02

    Blasters' air samples since 2017

    A public analysis of OSHA's air sampling results for painting contractors and shipyards, year by year from 2010 to 2026, for beryllium, crystalline silica, lead and arsenic. It shows how often samples exceeded today's limits before and after the 2017 beryllium rule. OSHA's records give the industry and the substance but not the task, so the analysis has to say that not every sample comes from blasting.

    The brief
    Credit · unclaimed

Open 01 · the brief

What is in the abrasive

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

A public table of abrasives on sale today, each product named. For each, an accredited laboratory analyzes its metals (arsenic, beryllium, cadmium, chromium, lead, manganese and nickel) and its crystalline silica, and the results are set beside what its safety data sheet declares.

Why it is still open

The last independent comparison across abrasive types, by KTA-Tator for NIOSH, tested products bought in the 1990s. CPWR found beryllium in coal slag in 2002 to 2004 and could not say whether safety data sheets now disclose it. The 2025 University of South Florida study analyzed two slags. A garnet seller's 2019 study of 21 products concluded that safety data sheets give limited information on heavy metals, but its page gives a result only for the seller's own product.

stacks.cdc.govelcosh.orgscirp.orggmagarnet.com

Built with what exists

Bags of abrasive bought from suppliers in at least three countries; a commercial laboratory accredited to ISO/IEC 17025 for metals by ICP-MS (EPA Method 6020) and crystalline silica by X-ray diffraction (NIOSH Method 7500); a language model such as Claude to read each safety data sheet into a fixed form (the Notes "Seven more flagged" and "A thousand questions, one pass" cover models that review documents and answer many fixed questions); a spreadsheet published on GitHub. Sealed bags are handled with gloves and a dust mask, and nothing is blasted.

  1. First step

    Buy five abrasives commonly used on bridges and in shipyards, download their safety data sheets, and get a quote from an accredited laboratory for the full analysis.

  2. Done looks like

    At least 25 products, covering coal slag, copper slag, garnet, crushed glass, staurolite and steel grit, each with laboratory results and safety data sheet side by side. The table counts each metal found that the sheet does not mention, with its level.

Open 02 · the brief

Blasters' air samples since 2017

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

A public analysis of OSHA's air sampling results for painting contractors and shipyards, year by year from 2010 to 2026, for beryllium, crystalline silica, lead and arsenic. It shows how often samples exceeded today's limits before and after the 2017 beryllium rule. OSHA's records give the industry and the substance but not the task, so the analysis has to say that not every sample comes from blasting.

Why it is still open

OSHA publishes the results of the samples its inspectors send to its laboratory, with industry code and substance, for 1984 to 2026. NIOSH's national analysis of OSHA silica samples by industry stops at 2015. The 2025 University of South Florida study says the 2020 revision of the beryllium rule relied on slag's low beryllium content "without supporting exposure data".

osha.goveutils.ncbi.nlm.nih.govscirp.org

Built with what exists

OSHA's Chemical Exposure Health Data downloads; Python and pandas; the North American Industry Classification System codes for painting and wall covering contractors (238320) and ship building and repairing (336611); GitHub for the notebook.

  1. First step

    Download OSHA's files for 2017 to 2026 and count the beryllium samples under the two industry codes.

  2. Done looks like

    A notebook that rebuilds every table from OSHA's raw files. For each year and each of the four substances it gives the number of personal samples and the share above the current OSHA limit, with the selection rules written out and checked by an occupational hygienist outside the team.