Industries / Industrial equipment and services / IoT and industrial automation
Industrial controls and PLCs
The industrial controls trade makes and programs the controllers that run machines and processes: programmable logic controllers (PLCs) on machines, plant-wide control systems in refineries and chemical plants, the operator screens and safety controllers that go with them, and the software used to write their programs.
1968
On 1 January 1968 Dick Morley of Bedford Associates, a small engineering firm in New England, wrote a 12-page memo describing a rugged, computer-like controller to replace the minicomputers then used to control machine tools; Control Engineering calls it "the earliest PLC documentation uncovered," and the controller became the Modicon 084.
37
Milestones achieved across 7 domains.
11
To watch for: announced, not yet confirmed outside.
14
Open deliverables. Nobody has shipped them.
In one minute
Where it started
In 1968 a small New England engineering firm and General Motors' Hydra-Matic division each set out to replace relay panels and minicomputers with a rugged controller that plant staff could reprogram. Modicon's 084 won at GM because it was programmed in ladder logic, drawn like the relay diagrams electricians already read, while its rivals had to be programmed in Boolean algebra. Plant-wide control systems, screen software for PCs and separate safety controllers followed between the mid-1970s and the late 1980s.
Where it stands
Dedicated controllers still run most machines: software PLCs, which run on ordinary computers, held 3.5% of the controller market in 2019 by IoT Analytics' estimate. Ethernet made up 79% of newly installed factory network nodes in 2026 by HMS Networks' estimate, and in 2026 Emerson and Schneider Electric brought out plant control systems that run as software on servers. Siemens, Schneider Electric and Beckhoff offer AI assistants that write and explain controller code, with no outside measurement of how well they work, while plants still run controllers that their makers no longer sell or repair.
What is open
Searches found no public test of how today's controllers stand up to network floods, how AI-written safety logic behaves when a part fails, or how accurately AI tools explain old programs, and no open table of when each controller line goes out of support. AI models that read and write code and documents, model checkers that prove programs correct, open-source PLC runtimes and cheap second-hand controllers now put each of these within reach of a small team with a test bench.
Domains
AchievedWatch forOpen
Domain
Progress
Last achieved
Watch for
Open
Programmable controllers
A programmable controller is the computer, in its own rugged box or as software on an ordinary one, that reads a machine's inputs and sets its outputs many times a second by following a program.
5 · 1 · 2
Last achievedReal-time Linux joins mainline2024
Watch forA controller sold as post-PLC
2
openPlant control systems
A plant control system, called a distributed control system (DCS) in the trade, runs a whole refinery, chemical plant or mill from one control room, with many controllers sharing one database, one network and one set of operator screens.
4 · 1 · 2
Last achievedA package unit plugs in2019
Watch forProcess control as server software
2
openOperator screens
Operator screens, called HMIs (human-machine interfaces) in the trade, are the displays and touch panels through which people watch and run machines and processes, built with screen-building software that is sold alongside the controllers.
4 · 1 · 2
Last achievedScreen designs put to test2004
Watch forScreens drawn from sketches
2
openProgramming
Programming is the writing, testing and managing of the programs that tell a controller what to do.
7 · 3 · 2
Last achievedLadder logic resists models2024
Watch forCopilots in makers' tools
2
openSafety controllers
Safety controllers are the separate devices and programs that stop a machine or bring a plant to a safe state when something goes wrong, built, certified and programmed to their own standards.
7 · 3 · 2
Last achievedA safety program proved2025
Watch forAI drafts safety code
2
openNetworks
Controller networks carry inputs, outputs and commands between a controller and its sensors, drives and other controllers, on a timetable the machine depends on.
5 · 1 · 2
Last achievedEthernet takes four in five2026
Watch forOne network to the drive
2
openReplacing old systems
Replacing old systems is the work of moving a running plant off controllers and control systems that their makers no longer sell or repair.
5 · 1 · 2
Last achievedSiemens ends S5 repairs2020
Watch forAI reads old programs
2
open
Advances to build with
1 research note
Open in industrial controls and plcs
3 of 14 open deliverables
Open · Programmable controllers
AI beside the control loop
An outside test that runs an AI model, such as an image check or an anomaly detector, on the same industrial computer as a software PLC, and measures how much the PLC's cycle timing wanders (its jitter) and how many cycles it misses, with and without the model running.
Built with what exists
Intel's CODESYS benchmark program and a PREEMPT_RT Linux kernel; the OpenPLC runtime; an NVIDIA Jetson board or a PC with a graphics card; ONNX Runtime to run open image models; a logic analyzer timing an output that the PLC toggles every cycle.
Open · Plant control systems
An MTP pairing table
A public test in which module files (MTPs) exported by every available module engineering tool are imported into every available orchestration system, the software that runs many modules as one plant. Each pairing is scored on whether the module's services start, hold and stop on command, whether its readings arrive, and whether its screens draw correctly.
Built with what exists
makers' MTP export and import tools on trial licences; open62541, an open-source OPC UA library (Mozilla Public License 2.0), to build simulated modules; the published parts of VDI/VDE/NAMUR 2658; Wireshark to record the OPC UA traffic.
Open · Operator screens
Screens from the drawing
A program that reads a P&ID (piping and instrumentation diagram, the drawing of every pipe, vessel, valve and instrument in a unit) and its tag list, and draws first-draft operator screens in an open HMI, with every symbol placed, labelled and linked to its tag, for an HMI engineer to finish.
Built with what exists
Dataset-P&ID, the Digitize-PID authors' public set; P&IDs in DEXPI, the open exchange format for plant drawings; AI models that read drawings, such as Claude or Gemini; FUXA, an open-source web-based HMI, as the target.
