Industries / Mining and materials / Steel and metals / Foundries and casting
Die casting
Die casting forces molten metal, mostly aluminum, zinc or magnesium, into a reusable steel mold called a die under high pressure, making precise, thin-walled parts in seconds.
5
Milestones achieved, from 1908 to 2023.
2
To watch for: announced, not yet confirmed outside.
2
Open deliverables. Nobody has shipped them.
The road
AchievedWatch forOpen
Achieved
1908
Die casting becomes a business
Herman H. Doehler founded the Doehler Die Casting Company in 1908, by the account of Euroguss, the European die-casting trade fair; other histories give 1905 for his first machine. A patent he shared with Joseph H. Bamberg, filed in 1917 and assigned to the Doehler Die-Casting Company of Brooklyn, New York, describes castings that leave the mold close to their final size and need only surface finishing.
Credit
Herman H. Doehler
1927
Metal poured into cold cylinder
In a hot-chamber machine the injection cylinder stays in the molten alloy; in a cold-chamber machine it sits outside the melt and is filled for each shot, which suits aluminum and magnesium, which melt at higher temperatures than zinc and lead, by Euroguss's account. Josef Polak's patent, first filed in Czechoslovakia on 1 September 1927 and granted in the US on 11 June 1929 as patent 1,717,254, describes a cylinder filled with molten metal before a plunger forces it into the molds, and is classed under cold-chamber machines.
Credit
Josef Polak
1932
Purer zinc stops swelling
Zinc die castings of the 1920s could swell, warp and in extreme cases fall apart as oxidation ran along the boundaries between the metal's grains. Edmund A. Anderson and George L. Werley of the New Jersey Zinc Company wrote in their patent that lead "very seriously diminishes" the alloy's resistance to this attack, and claimed zinc with about 4% aluminum and 0.1% magnesium, made from high-purity zinc with no more than 0.01% lead and cadmium together (US patent 1,852,441, filed 1930, granted 5 April 1932). The zinc industry's die-casting site still says that keeping lead, cadmium and tin low and adding a little magnesium prevents the attack, and today's European standard caps lead and cadmium at about 0.005% and tin at 0.002%.
LessonA hundredth of a percent of lead decided whether a casting lasted.
Credit
Edmund A. Anderson and George L. Werley, New Jersey Zinc Company
2018
One fire stops pickups
On 2 May 2018 explosions and a fire wrecked much of Meridian Magnesium Products' die-casting plant in Eaton Rapids, Michigan, which made magnesium structural parts such as instrument-panel crossbeams and radiator supports. Ford, which reportedly took about a third of the plant's output, stopped building F-150 and Super Duty pickups at three plants, and General Motors, Fiat Chrysler and others lost production. F-150 assembly restarted on 18 May after Ford and Meridian moved 19 salvaged dies to Meridian's plant in Nottingham, England.
LessonProduction came back only because the dies survived and could be moved; a part cast from one set of dies in one plant has no fallback.
Credit
reported by Robert Brooks in Foundry Management & Technology
2023
Big presses spread in China
In December 2023 Gasgoo, a Chinese automotive news service, reported that XPeng used a 12,000-tonne die-casting machine, AITO a 9,000-tonne one and Zeekr a 7,200-tonne one to cast large one-piece body parts, and that most electric-car makers' machines ranged from 6,000 to 9,000 tonnes. The tonnage is the clamping force that holds the die's two halves shut against the injection pressure.
Credit
XPeng, AITO and Zeekr, as reported by Gasgoo
Watch for
16,000-tonne machines in production
Guangdong Hongtu Technology says in its 2025 annual report that its 16,000-tonne die-casting unit is the largest-tonnage equipment in mass production in the world. Separately, a plant built for Dongfeng Motor with one 16,000-tonne and one 10,000-tonne line was completed in September 2025, with mass production of rear floors and battery casings expected from June 2026, according to its builder and public filings reported by Gasgoo.
Achieved whenan outside party, such as a trade journal visit or a customer's teardown, reports parts made in volume on a 16,000-tonne machine.
Claimed by
Guangdong Hongtu Technology, April 2026; Dongfeng Motor's builder, September 2025
A printed die insert
MacLean-Fogg and Fraunhofer ILT say they made what they believe is the world's largest nearly solid 3D-printed die-casting insert, 156 kg, printed by laser powder bed fusion from MacLean-Fogg's L-40 tool steel for the die that casts the transmission housing of Toyota Europe's Yaris hybrid. Printing allows internal cooling channels that machining cannot make, and MacLean-Fogg says L-40 gives nearly double the service life of conventional inserts.
Achieved whenToyota or an outside party publishes the shot count the insert reached in production beside that of a conventional insert.
Claimed by
MacLean-Fogg, Fraunhofer ILT and Toyota Europe, October 2025
Open
01
Shot curves joined to defects
An open data set of die-casting shots in which each shot's machine record (plunger position, speed and pressure over time, die and coolant temperatures, spray times) is joined by part number to the inspection result for the same part, such as an X-ray grade, a leak test or a scrap reason, with a baseline model that predicts scrap and is tested on a die it was not trained on.
The briefCredit · unclaimed02
Die photos to die life
A set of photographs of die surfaces taken at each maintenance stop, with the shot count, and with the heat checking (the network of fine cracks that heating and cooling on every shot leaves on a die) marked by toolmakers, plus a model that estimates how many shots remain before the die insert needs repair. The same data would let outsiders test claims such as MacLean-Fogg's on insert life.
The briefCredit · unclaimed
Open 01 · the brief
Shot curves joined to defects
The first to publish is credited on this line, and the deliverable moves from Open to Achieved.
What to build
An open data set of die-casting shots in which each shot's machine record (plunger position, speed and pressure over time, die and coolant temperatures, spray times) is joined by part number to the inspection result for the same part, such as an X-ray grade, a leak test or a scrap reason, with a baseline model that predicts scrap and is tested on a die it was not trained on.
Why it is still open
Published studies use private data. Pachandrin, Norbert Hoffmann and Klaus Dilger (2025) trained models on 7,982 cycles from a 2006 research casting series run by Bühler and DGS Druckguss Systeme and give no download link; the work they cite by Kopper and co-authors used 950,000 cycles from 12 die-casting cells. In November 2026 a Zenodo search for "die casting" returned papers, a simulation program and an alloy data set but no shot-by-shot process data, and Hugging Face returned nothing.
Built with what exists
The shot-curve export of the casting machine, which Bühler's machine provided in the 2006 series; cycle and cavity numbers engraved on each part, as in that series; Python with pandas, scikit-learn and XGBoost; Zenodo to publish.
First step
Ask one die caster for a month of anonymized shot logs and scrap records from one casting cell, and test whether parts can be matched to shots.
Done looks like
At least 50,000 shots from at least two dies in two plants, each joined to a part-level quality result, published under an open license, with the baseline model's precision and recall for scrap reported on a held-out die.
Open 02 · the brief
Die photos to die life
The first to publish is credited on this line, and the deliverable moves from Open to Achieved.
What to build
A set of photographs of die surfaces taken at each maintenance stop, with the shot count, and with the heat checking (the network of fine cracks that heating and cooling on every shot leaves on a die) marked by toolmakers, plus a model that estimates how many shots remain before the die insert needs repair. The same data would let outsiders test claims such as MacLean-Fogg's on insert life.
Why it is still open
Heat checking has been measured by image analysis on laboratory test pieces. S. Le Roux and co-authors (2013) followed crack patterns under a scanning electron microscope on hot-work tool steel specimens cycled in a thermal-fatigue rig. Crossref searches in November 2026 for crack detection on die-casting die surfaces returned studies of concrete, tunnels and other surfaces, none of dies.
Built with what exists
A camera with a ring light and a printed scale in frame; Label Studio for marking cracks; Ultralytics YOLO or a U-Net for crack segmentation; the Python lifelines library for remaining-life models.
First step
Ask one die shop to photograph one insert at every maintenance stop for a month, with the shot counter in the picture.
Done looks like
At least 2,000 photographs from at least 20 inserts followed until repair or scrapping, published under an open license, with the model's error in predicted remaining shots reported on inserts held out of training.