BRENNEN

Industries / Transport and vehicles / Maritime and shipping / Barge and inland waterways / Fleeting services

Cleaning and repair

Between cargoes a barge is swept, washed or stripped of what it last carried, and its leaks, dents and worn steel are mended, often at the fleet where it waits.

7

Milestones achieved, from 1922 to 2024.

2

To watch for: announced, not yet confirmed outside.

2

Open deliverables. Nobody has shipped them.

The road

AchievedWatch forOpen

Achieved

  1. 1922

    Chemists certify tanks

    After the First World War, fires and explosions rose in US yards as ships were converted and repaired. In 1922 the National Fire Protection Association (NFPA) adopted rules for freeing tanks of flammable vapors before repairs. They required a certified chemist to test and inspect any tank where hot work (welding, cutting or other work that makes heat or sparks) was planned, and the American Bureau of Shipping certified the first 25 "gas chemists" that year. NFPA took over their training and certification in 1963, and the rules became its standard NFPA 306. US shipyard safety rules now bar hot work in or next to a space that has held flammable liquids or gases until a Marine Chemist or a person authorized by the Coast Guard has tested it and certified it "Safe for Hot Work."

    marinelink.commaritimeprofessional.comlaw.cornell.edu

    Credit

    National Fire Protection Association; American Bureau of Shipping; Occupational Safety and Health Administration

  2. 2000

    Limits on wash water

    The US Environmental Protection Agency issued its Transportation Equipment Cleaning rules in 2000. They cover the water used to wash the insides of tanks on trucks, rail cars, barges and ships. One part applies to "discharges resulting from the cleaning of tank barges or ocean/sea tankers which have been used to transport chemical or petroleum cargos," and sets daily and monthly limits on oxygen-consuming matter, suspended solids, oil and grease, and seven metals, among them cadmium, copper, lead and mercury. A facility that discharges less than 100,000 gallons of such wash water a year is exempt. EPA counts about 2,400 facilities that clean tanks of all these kinds.

    epa.govlaw.cornell.edulaw.cornell.edulaw.cornell.edu

    Credit

    US Environmental Protection Agency

  3. 2009

    The receiver pays for cleaning

    Belgium, France, Germany, Luxembourg, the Netherlands and Switzerland signed a convention on waste from Rhine and inland navigation, known as the CDNI, on 9 September 1996, and it came into force on 1 November 2009. For each cargo it names the state in which a vessel must be handed back: a "swept hold" cleared with brooms or mechanical sweepers, a "vacuum cleaned hold," a "stripped" tank, or a washed one, and it says where the wash water may go. For dry goods the party receiving the cargo must return the hold to that standard and, in the CDNI's words, "bears any cleaning and washing costs." A paper called the attestation of unloading records that it was done. A tanker's stripping system must leave no more than 5 liters on average in each tank of a double-hull vessel.

    LessonThe convention puts the cleaning bill on the party that received the cargo, so the skipper has less reason to wash residues into the river.

    cdni-iwt.orgcdni-iwt.orgcdni-iwt.orgcdni-iwt.org

    Credit

    the six CDNI states; the CDNI Secretariat at the Central Commission for the Navigation of the Rhine

  4. 2011

    Fire under the hold

    At Texas Barge & Boat in Freeport, Texas, a yard that repairs boats and barges, nine employees were cutting steel and standing fire watch inside a hopper space, the gap between a vessel's cargo hold and its bottom plate, when a flash fire killed two of them. The Occupational Safety and Health Administration (OSHA) opened its inspection on 2 April 2011 and cited the company for one willful violation, for failing to test the air before employees entered the confined space to cut with oxygen and fuel gas, and for 39 serious ones, with proposed penalties of $221,200.

    LessonThe air in a closed space of a vessel has to be tested before anyone cuts steel there.

    ohsonline.com

    Credit

    OSHA, Houston South Area Office

  5. 2019

    Static ignites a barge

    On 4 November 2019 the tank barge IB1940 exploded at Illinois Marine Towing's cleaning slip on the Chicago Sanitary and Ship Canal at Lemont, Illinois, while workers prepared to clean out the remains of an acetone cargo. Nobody was hurt, and the barge, valued at $1.75 million, was a total loss. The job was a "strip-and-blow": a vacuum truck sucks out the leftover liquid, then air movers, blowers with no moving parts driven by compressed air, push fresh air through the tanks. The National Transportation Safety Board (NTSB) found that one air mover had been set on a painted hatch without a bonding strap, a wire that lets static charge drain to the barge's steel, and that a static spark most likely lit the vapor. The facility's manual called for bonding, but the three-page procedure the crew worked from did not. The company replaced it with a 13-page procedure.

    LessonA safety step that sits in the facility manual but not in the crew's working procedure does not get done.

    ntsb.govntsb.gov

    Credit

    National Transportation Safety Board; Illinois Marine Towing

  6. 2020

    Wash stations sit idle

    Chinese rules require inland vessels that carry liquid dangerous goods in bulk to clean their tanks after unloading at a wharf, a special anchorage or a tank washing station. A national plan laid out 13 washing stations on the main line of the Yangtze, sized to wash 7,800 vessels a year by 2020. Researchers at the China Waterborne Transport Research Institute and the Ministry of Transport found that by the end of 2020 the 13 stations together had done little more than 200 washes. They gave two reasons: washing cost too much, with most of the cost falling on the terminal, and no official list said which changes of cargo require a wash.

    LessonBuilding cleaning stations does not bring vessels to them unless a rule says when a wash is required and who pays.

    atlantis-press.com

    Credit

    Hongyan Wang, Lei Chen and Yujun Tian

  7. 2024

    Venting vapors banned

    After a tanker unloads gasoline or benzene, vapor stays in its cargo tanks, and crews long blew it into the open air while sailing, a practice called degassing or venting. An amendment to the CDNI that came into force on 1 October 2024 bans this for the most harmful cargoes: benzene, gasoline, oil distillates and mixtures with more than 10 percent ethanol. The vapor must go to a degassing station unless the next cargo is the same or compatible. A second phase on 1 October 2026 added three more groups of substances, and a third is due on 1 October 2027. In the Netherlands the transport inspectorate, the ILT, set fines of €30,000 for a first offense and said it would look for offenders with drones and e-noses, which are sensors that detect vapors. In July 2024 the trade paper SWZ Maritime reported that only one degassing installation, at Moerdijk, was open to inland tankers in the country.

    LessonA ban on venting works only if vessels have somewhere to take the vapor, and the stations came later than the rule.

    cdni-iwt.orgcdni-iwt.orgswzmaritime.nl

    Credit

    the six CDNI states; the CDNI Secretariat

Watch for

  1. Ninety-five percent less venting

    The CDNI Secretariat says that once the venting ban is fully phased in, 95 percent of harmful vapor releases to the air will be avoided across the six member states. The figure comes from the impact study done for the amendment, not from measurement. Detection is still weak: a 2025 Utrecht University thesis that tried to spot venting from vessel tracks found 42.1 percent of 242 known cases.

    Achieved whenafter the third phase starts on 1 October 2027, an inspectorate or an independent body publishes measured releases, or counts of venting events detected, from before and after the ban.

    cdni-iwt.orgcdni-iwt.orgstudenttheses.uu.nl

    Claimed by

    CDNI Secretariat, October 2026

  2. Robots blast barge hulls

    Before a barge is repainted, its old paint and rust are blasted off with grit, by hand a slow and dusty job. C&C Marine and Repair of Belle Chasse, Louisiana, says it has blasted more than 700 barges since November 2018 in an enclosed building with three blasting robots. It says each robot covers 2,000 square feet an hour, that a standard hopper barge takes one-fourth of the time of manual blasting, and that its filters catch more than 99 percent of airborne dust.

    Achieved whena barge owner or a coatings inspector outside the company publishes blast times and coating life for barges done there against barges blasted by hand.

    marinelink.commarinelog.com

    Claimed by

    C&C Marine and Repair, April 2026

Open

  1. 01

    Weigh what sweeping leaves

    A measured table of how much cargo stays on a steel hold floor after each cleaning method named in Europe's unloading standards (broom, mechanical sweeper and vacuum) for five common dry bulk cargoes, and a phone-photo method that estimates the residue per square meter.

    The brief
    Credit · unclaimed
  2. 02

    Measure static on air movers

    Bench measurements of how much static charge builds up on the compressed-air blowers used to ventilate tanks, with and without a bonding strap, and with the strap's clamp on paint, on rust and on bare steel. The test uses air only, with no flammable liquid or vapor anywhere near it.

    The brief
    Credit · unclaimed

Open 01 · the brief

Weigh what sweeping leaves

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

A measured table of how much cargo stays on a steel hold floor after each cleaning method named in Europe's unloading standards (broom, mechanical sweeper and vacuum) for five common dry bulk cargoes, and a phone-photo method that estimates the residue per square meter.

Why it is still open

The CDNI defines a swept hold in words, as one "cleared of residual cargo by cleaning methods such as brooms or mechanical sweepers," and a vacuum cleaned hold as one with "considerably fewer cargo residues than a swept hold." It gives no quantity for either, though it gives one for tankers: 5 liters on average per tank. A search for measurements of what stays in a swept hold of an inland vessel found none.

cdni-iwt.org

Built with what exists

a mock hold floor of steel plate about 2 m square, with one welded corner and one frame, set up in a workshop; corn, soybean meal, sand, gravel and wood pellets; a push broom, a walk-behind sweeper and a shop vacuum; a scale that reads to 1 g; a phone camera; OpenCV or Ultralytics YOLO11 segmentation to measure how much floor the residue covers; Python.

  1. First step

    spread 20 kg of corn on one square meter of steel plate, sweep it off with a broom, vacuum up what is left and weigh it.

  2. Done looks like

    grams per square meter left by each method for each cargo, ten repeats each, on smooth plate and on rusted, pitted plate; a photo estimate within 25 percent of the weighed residue on trials held back from training; data, photos and code published, and the table sent to the CDNI Secretariat for comment.

Open 02 · the brief

Measure static on air movers

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

Bench measurements of how much static charge builds up on the compressed-air blowers used to ventilate tanks, with and without a bonding strap, and with the strap's clamp on paint, on rust and on bare steel. The test uses air only, with no flammable liquid or vapor anywhere near it.

Why it is still open

The NTSB found that the 2019 explosion of barge IB1940 was most likely lit by a static spark from an air mover that rested on painted steel without a bond, and it notes that the Coast Guard's Safety Alert 01-20 urged operators to bond air movers and inspect the bond before use. A 2005 article in Occupational Health & Safety by Dave Angelico, writing for a maker of ventilation equipment, said many procedures state that static charges should be removed "but few tell the worker how to do it," and that the standards lack "how to set up and test a complete grounded ventilation system". A search found no published voltage measurements for these blowers.

ntsb.govohsonline.com

Built with what exists

a rented venturi air mover and a shop compressor, run with and without an air dryer; a steel plate on insulating blocks with a hatch-sized opening, painted on one half; a bonding strap and clamp; a handheld electrostatic field meter; an insulation tester to measure the resistance of each bond; a humidity and temperature logger.

  1. First step

    measure the resistance between a bonding clamp and a painted steel plate, then between the clamp and a spot scraped bare.

  2. Done looks like

    the voltage on the air mover's body against time for four cases (bonded to bare steel, clamp on paint, clamp on a rope, no strap), in dry and in humid air and with dry and wet supply air, ten runs each; the resistance of each bond; the method and all readings published and sent to the NTSB and the Coast Guard for comment.