Industries / Industrial equipment and services / Industrial services / Crane and rigging
Heavy transport
Heavy transport moves loads too big or heavy for ordinary trucks, such as transformers, plant modules and whole structures, on modular trailers, self-propelled transporters, jacks and skids, along routes that have to be surveyed and permitted first.
7
Milestones achieved, from 1956 to 2016.
2
To watch for: announced, not yet confirmed outside.
2
Open deliverables. Nobody has shipped them.
The road
AchievedWatch forOpen
Achieved
1956
Axles that share the load
Willy Scheuerle invented the hydraulically suspended oscillating axle in 1956, and in 1972 the electronic multidirectional steering later used on heavy transporters. On such trailers each axle rides on one hydraulic cylinder, the cylinders are joined in groups called hydraulic zones, and the load on a zone is shared equally by all of its axles.
Credit
Willy Scheuerle, Scheuerle Fahrzeugfabrik (now TII Scheuerle)
1983
Transporters that drive themselves
Scheuerle and the Dutch heavy-lift firm Mammoet launched the self-propelled modular transporter (SPMT) at Pfedelbach, Germany, in 1983: a platform on many steerable axles, driven by its own power pack, that joins with others into larger units. Mammoet says its 2.43 m width let modules ship on standard container flat racks, where earlier axle lines were at least 3 m wide, and that the first units went to work in 1984 on modules for offshore oil and gas platforms. TII says plant builders had been limited to blocks of about 300 tonnes before, and that tens of thousands of its SPMT axle lines are now in use.
Credit
Scheuerle Fahrzeugfabrik and Mammoet
1999
A lighthouse rolls inland
Between 17 June and 9 July 1999 the Cape Hatteras Lighthouse in North Carolina, a 4,830-ton tower built in 1870, was moved 2,900 feet (about 880 m) away from the eroding shore. Crews replaced its foundation with steel beams, raised it 6 feet with hydraulic jacks, and rolled it on track beams, pushed forward 5 feet at a time by jacks clamped to the track. The US National Park Service, which owns the tower, had the light working again on 13 November 1999.
Credit
International Chimney Corp. of Buffalo, New York, with Expert House Movers of Maryland, for the National Park Service
2001
A submarine on strand jacks
On 8 October 2001 the Mammoet-Smit joint venture began lifting the wreck of the Russian nuclear submarine Kursk from 108 m down in the Barents Sea, with 26 strand jacks on the barge Giant 4. A strand jack is a hydraulic jack that pulls a bundle of steel cables through itself in short strokes, gripping and releasing in turn. Each jack had a heave compensator to steady its cables against the swell, and Smit had first cut off the submarine's bow with a saw wire. Smit puts the load at about 9,000 tonnes and calls it a world record for the heaviest object recovered from such a depth; the environmental group Bellona reported the lift as it began.
Credit
Mammoet and Smit
2007
Permits go online in Germany
Germany's states and federal government began handling permits for oversized and heavy road transports through VEMAGS, a shared online system, in 2007. Before it, an application was faxed from the permitting office to each authority along the route and back. The Hessian road authority that led the project later counted 300,000 permits handled online since 2007, for about 3,300 applicants and 1,000 authorities.
Credit
Hessian state road and transport authority (HLSV), with the consultancy Steria Mummert, for all the federal states
2013
Oversize load fells a bridge
On 23 May 2013 a permitted oversize load, 15 feet 11 inches (4.85 m) high as measured afterwards, struck the overhead truss of the Interstate 5 bridge over the Skagit River in Washington State, and one 160-foot span fell into the river with two vehicles; three people had minor injuries. The National Transportation Safety Board found weak route planning by the carrier and driver, a pilot car driver who failed to warn of the low clearance, distracted in part by phone use, and a state transportation department that evaluated the permit request inadequately and posted no low-clearance warning signs.
LessonA permit, a survey and a pilot car only protect a bridge if each one actually checks the route's lowest clearance.
Credit
National Transportation Safety Board (NTSB), report adopted 15 July 2014
2016
Heaviest move on record
Guinness World Records lists the heaviest load moved by SPMTs as a 14,754.19-tonne block, 110.5 m long, 50 m wide and 40 m high, moved by KCTC Co., Ltd. at Goseong, South Korea, on 23 June 2016. Companies have since claimed heavier moves that the Guinness page does not list: TII says Mammoet moved 20,300 tonnes, and Fagioli said in May 2024 that it moved a 23,163-tonne ship hull in Texas on 800 SPMT axle lines.
Credit
KCTC Co., Ltd.; record confirmed by Guinness World Records
Watch for
Germany switches permit systems
German heavy-transport permits are to move from VEMAGS 7.5 to VEMAGS 7.6 at the same time as new guidelines for oversized and heavy transports, RGST 2026, take effect. Under the current schedule, 7.5 shuts at 18:00 on 31 March 2027 and applications not yet approved must be filed again in 7.6 from 1 April 2027. On 16 October 2026 an alliance of industry associations, VI GST, whose members include the BDI and the VDMA, warned the transport minister of a permit backlog for infrastructure, energy and military transports, and proposed copying open applications across automatically or opening 7.6 on 1 March 2027.
Achieved whenVEMAGS 7.6 and RGST 2026 are both in force and the authorities' published permit processing times are no longer than before the switch.
Claimed by
the federal and state schedule, as reported by transport-online.de, October 2026
Battery-powered transporters
Anhui SuperTransport Heavy-Load Robot Co., founded in 2024 in Xuancheng, China, calls its APMT the "world's first fully electric-driven intelligent modular transport platform": six axle lines carrying up to 255 tonnes on a 400.61 kWh lithium iron phosphate battery from CATL, with CE certification and, by its account, jobs in offshore wind, petrochemicals and ports in China. Mammoet made a similar first claim in April 2022, for a vessel swap at a Shell site in the Netherlands on one Scheuerle SPMT module driven by an electric power pack.
Achieved whenan outside party reports battery-powered transporters moving commercial loads over a stated period, with the loads, operating hours and charging measured.
Claimed by
Anhui SuperTransport, June 2026, in Breakbulk magazine
Open
01
Oversize permit rules as data
A free, versioned rule set for oversize and overweight permits in all 50 US states and the District of Columbia: the width, height, length and weight above which a permit is needed; the sizes that call for one or two pilot cars (escort vehicles that lead or follow the load and check clearances) or a police escort; travel-time limits; and pilot-car certification rules. Every value links to the statute, rule or permit manual it comes from. A checker takes a load's dimensions and the states on its route and lists every requirement.
The briefCredit · unclaimed02
Trailer stability, open and tested
An open calculator for the stability check that the European heavy-transport association ESTA published in 2023 for modular hydraulic trailers and SPMTs, validated on a bench model. It works out the combined center of gravity, the load on each hydraulic zone under braking, wind and road camber (the sideways slope of a road), the guideline's rule that no bogie (a single axle on one hydraulic cylinder) may drop below 60% of its static load, and its simplified check of a tipping angle of at least 9 degrees. The model is a 1:20 trailer with a load cell under each of three hydraulic zones, tilted on a table.
The briefCredit · unclaimed
Open 01 · the brief
Oversize permit rules as data
The first to publish is credited on this line, and the deliverable moves from Open to Achieved.
What to build
A free, versioned rule set for oversize and overweight permits in all 50 US states and the District of Columbia: the width, height, length and weight above which a permit is needed; the sizes that call for one or two pilot cars (escort vehicles that lead or follow the load and check clearances) or a police escort; travel-time limits; and pilot-car certification rules. Every value links to the statute, rule or permit manual it comes from. A checker takes a load's dimensions and the states on its route and lists every requirement.
Why it is still open
The US Government Accountability Office (GAO) collected all 51 jurisdictions' permit practices in 2015, checked by state officials and published as one CSV file, but that is a ten-year-old snapshot that nobody maintains. FHWA's 2018 best-practices report tables automatic-issue limits and pilot-car certifications in a PDF. Commercial guides such as Oversize.io, and the free state pages of J.J. Keller's permit service, describe state rules in prose without citing the rule behind each figure and tell operators to check each state. The NTSB traced the 2013 Skagit River collapse partly to permitting and route-survey failures. I found no free, maintained, machine-readable set.
files.gao.govops-dr.fhwa.dot.govoversize.iokellerpermits.comntsb.gov
Built with what exists
State permit manuals and statutes; GAO's 2015 CSV as a starting point; a document-reading AI model to pull rules out of manuals, with every value checked by a person (see the Note "Seven more flagged"); JSON Schema and Python for the rule set and checker.
First step
Code five neighboring states (for example Washington, Oregon, Idaho, Montana and Wyoming) from their current permit manuals, and list every value that has changed since GAO's 2015 rows.
Done looks like
All 51 jurisdictions coded with at least 15 fields each, every value sourced; 100 sample loads, each crossing three to six states, run through the checker and compared with written answers from two professional permit services; agreement published field by field, with a target of 95% or better.
Open 02 · the brief
Trailer stability, open and tested
The first to publish is credited on this line, and the deliverable moves from Open to Achieved.
What to build
An open calculator for the stability check that the European heavy-transport association ESTA published in 2023 for modular hydraulic trailers and SPMTs, validated on a bench model. It works out the combined center of gravity, the load on each hydraulic zone under braking, wind and road camber (the sideways slope of a road), the guideline's rule that no bogie (a single axle on one hydraulic cylinder) may drop below 60% of its static load, and its simplified check of a tipping angle of at least 9 degrees. The model is a 1:20 trailer with a load cell under each of three hydraulic zones, tilted on a table.
Why it is still open
ESTA's guideline sets out the method in text and formulas but ships no software; ESTA's earlier guidance used measured stability, and the calculated method dates only from October 2023. Heavy-lift firms keep their own tools: Sarens described in 2019 its Transport Calculation Sheet, which checks axle loads, tipping angles, ground pressure and trailer bending for every special transport it runs, but it is in-house and its results are not published against tests. Published research models SPMT driving dynamics in a simulator (Cai and colleagues, IEEE Intelligent Vehicles Symposium 2024), and a 2026 ADIPEC paper benchmarked weighing a module through SPMT suspension pressures against jacks on one offshore topside. I found no open implementation of the guideline and no published comparison of its results with a physical model.
Built with what exists
Python with NumPy; the ESTA GD23018 text (CC BY-NC-ND 4.0); a 3D-printed or aluminum 1:20 trailer frame; three to six 50 kg load cells with HX711 amplifiers on an Arduino; a tilting table with a digital inclinometer; a fan for wind load; a coding agent to write test cases (see the Note "Checked without being asked").
First step
Code the simplified check in section 5.3 of the guideline and run it on three cases worked by hand.
Done looks like
30 load cases with the center of gravity raised and shifted; predicted and measured zone loads agree within 5%, and predicted and measured tipping angles within 1 degree; code, drawings and data published.