BRENNEN

Industries / Construction and property / Commercial and residential construction

Site safety

This work keeps construction workers alive and unhurt, through protective gear, laws and regulators, fall protection, limits on dust and heat, and equipment that watches for hazards.

7

Milestones achieved, from 1919 to 2021.

2

To watch for: announced, not yet confirmed outside.

2

Open deliverables. Nobody has shipped them.

The road

AchievedWatch forOpen

Achieved

  1. 1919

    The hard hat

    The E. D. Bullard Company of San Francisco made the "Hard Boiled" helmet from canvas, glue and black paint, modeled on the "doughboy" helmets of World War I soldiers. The Smithsonian's National Museum of American History holds a Hard Boiled miner's helmet made "after 1919" and calls Bullard "one of the first producers of protective hard hats". US construction rules now require head protection wherever falling or flying objects, impact or electric shock could injure the head.

    americanhistory.si.eduosha.gov

    Credit

    E. D. Bullard Company

  2. 1970

    Laws make employers responsible

    The US Occupational Safety and Health Act became law on 29 December 1970 and created OSHA, the Occupational Safety and Health Administration. Britain's Health and Safety at Work etc. Act followed on 31 July 1974. OSHA, citing Bureau of Labor Statistics data, says US worker deaths in all industries fell from about 38 a day in 1970 to 15 a day in 2023.

    osha.govosha.govlegislation.gov.uk

    Credit

    US Congress and OSHA; UK Parliament and the Health and Safety Executive (HSE)

  3. 1987

    A building falls during lifting

    L'Ambiance Plaza in Bridgeport, Connecticut, was being built by the lift-slab method, in which floor slabs are cast in a stack at ground level and jacked up the columns. On 23 April 1987 it collapsed and killed 28 workers. The National Bureau of Standards, investigating at OSHA's request, found the most probable cause was a lifting nut slipping off a deformed steel angle at one jack. OSHA's lift-slab rule, effective 17 December 1990, requires a registered engineer with lift-slab experience to plan the lift, and keeps workers not needed for jacking out of the building during lifts unless an independent engineer confirms that losing any one jack would cause only local damage.

    LessonA structure still being built can be brought down by one failed support, so the temporary stage needs an engineer's plan and nobody unnecessary inside.

    nvlpubs.nist.govgovinfo.govosha.gov

    Credit

    National Bureau of Standards (now NIST); OSHA

  4. 1992

    Europe requires safety planning

    EU Council Directive 92/57/EEC of 24 June 1992, on temporary or mobile construction sites, makes the client or project supervisor appoint safety and health coordinators where several firms share a site, have a health and safety plan drawn up before work starts, and notify the authorities of larger sites: those running more than 30 working days with more than 20 workers at once, or more than 500 person-days of work.

    osha.europa.eu

    Credit

    Council of the European Communities, as summarized by the EU safety agency EU-OSHA

  5. 1994

    Fall protection from six feet

    OSHA's construction fall protection rules, published on 9 August 1994, require a guardrail, a safety net or a personal fall-arrest system, a harness and lanyard tied to an anchor, at any edge 6 ft (1.8 m) or more above a lower level. Falls are still the top killer: 389 of 1,034 US construction deaths in 2024 were falls to a lower level, by Bureau of Labor Statistics data cited by OSHA, and falls from height caused 53% of construction worker deaths in Great Britain from 2020/21 to 2024/25, by HSE's count.

    osha.govosha.govhse.gov.uk

    Credit

    OSHA; Bureau of Labor Statistics; HSE

  6. 2016

    Silica dust limit cut

    Respirable crystalline silica is the fine dust from cutting or grinding concrete, stone and brick, and it causes silicosis, lung cancer and kidney disease. OSHA's final rule of 25 March 2016 set the limit at 50 micrograms per cubic meter of air averaged over 8 hours, with construction firms to comply by 23 September 2017, and lists accepted controls such as water or vacuum dust collection on saws and jackhammers.

    LessonOSHA concluded that workers exposed at the old limits still faced "a significant risk".

    federalregister.govosha.gov

    Credit

    OSHA

  7. 2021

    A measured heat limit

    Qatar's Ministerial Decision No. 17 of 2021 bans outdoor work from 10:00 to 15:30 between 1 June and 15 September, and requires employers to measure wet-bulb globe temperature (WBGT), a heat-stress index that combines temperature, humidity, sun and wind. Work must stop wherever WBGT goes above 32.1 °C, and workers may stop work and complain to the ministry. It replaced a 2007 rule that banned only 11:30 to 15:00, from 15 June to 31 August.

    ilo.orgilo.org

    Credit

    Qatar's Ministry of Labour, with a translation and summary hosted by the International Labour Organization (ILO)

Watch for

  1. A US heat standard

    OSHA proposed a rule to prevent heat injury and illness on 30 August 2024, held a public hearing from 16 June to 2 July 2025, and closed post-hearing comments on 30 October 2025; its page gives no final rule or next step.

    Achieved whenA final rule is published in the Federal Register and takes effect.

    osha.gov

    Claimed by

    OSHA, August 2024 and June 2025

  2. AI watching site cameras

    viAct, a Singapore company, and Alliad, a contractor based in Dubai, ran AI video analysis on Alliad's existing cameras at a healthcare construction project in Côte d'Ivoire, and report 41.7% less non-use of protective equipment and 46.3% fewer danger-zone violations in the first three months. They did not publish baseline counts, the number of cameras or an outside audit.

    Achieved whenAn insurer, regulator or researcher publishes before-and-after injury or violation rates with their baselines.

    technode.global

    Claimed by

    viAct and Alliad, September 2026

Open

  1. 01

    Photo check of harness damage

    An open, labeled image set of damage to fall-arrest harnesses, such as cuts, abrasion, burns, broken stitching, bent D-rings and triggered fall indicators, and a vision model that flags harnesses to take out of service.

    The brief
    Credit · unclaimed
  2. 02

    Snaphook hookup checker

    A classifier that says whether a snaphook or connector hookup is one of those OSHA bans: clipped straight to webbing or rope, to another snaphook, onto a D-ring that already holds a connector, onto a horizontal lifeline, or onto an object that can press the hook's gate open. All hookups are staged at ground level.

    The brief
    Credit · unclaimed

Open 01 · the brief

Photo check of harness damage

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

An open, labeled image set of damage to fall-arrest harnesses, such as cuts, abrasion, burns, broken stitching, bent D-rings and triggered fall indicators, and a vision model that flags harnesses to take out of service.

Why it is still open

OSHA requires each fall-arrest system to be "inspected prior to each use for wear, damage, and other deterioration", and the check is done by eye. The harness image sets and papers found in this research label whether a harness is worn or a safety rope used, not the harness's condition.

osha.govgithub.comdoi.org

Built with what exists

Harnesses already retired and tagged out of service; a light box; a phone camera; an open object detector. Nobody wears them and nothing is load-tested.

  1. First step

    Ask a tool-rental yard or contractor for its retired harnesses, and photograph each against a fixed checklist.

  2. Done looks like

    About 1,000 labeled images from at least 30 harnesses released openly, then 20 unseen harnesses scored by both the model and a competent person, with a published tally that counts every missed defect.

Open 02 · the brief

Snaphook hookup checker

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

A classifier that says whether a snaphook or connector hookup is one of those OSHA bans: clipped straight to webbing or rope, to another snaphook, onto a D-ring that already holds a connector, onto a horizontal lifeline, or onto an object that can press the hook's gate open. All hookups are staged at ground level.

Why it is still open

The rule is checked by eye. The vision work found in this research detects whether a harness is worn, not how its connector is clipped.

osha.gov

Built with what exists

A ground-level anchor board; assorted connectors and lanyards; a phone camera; an open image model.

  1. First step

    Photograph each banned hookup and an allowed counterpart under three kinds of lighting.

  2. Done looks like

    300 staged photos labeled by a competent person, then 20 filmed new setups, with a published tally of correct and incorrect calls.