Industries / Transport and vehicles / Automotive
Powertrain and batteries
This is the work of designing and making what moves the car: the engine or electric motor, the transmission that carries their turning force to the wheels, and the battery that stores the energy.
7
Milestones achieved, from 1912 to 2026.
3
To watch for: announced, not yet confirmed outside.
2
Open deliverables. Nobody has shipped them.
The road
AchievedWatch forOpen
Achieved
1912
Electric starter ends cranking
Drivers used to start the engine by turning a crank by hand, which took strength and quick reflexes. Charles Kettering's electric starter turned the engine over instead, and Cadillac fitted it to its 1912 models.
Credit
Charles F. Kettering and the Dayton Engineering Laboratories Company (Delco); Cadillac
1940
Automatic gearbox in mass production
General Motors' Hydra-Matic Drive changed gears with no clutch pedal, and Oldsmobile offered it for the 1940 model year. The Henry Ford museum calls it the first mass-produced, fully automatic transmission in a passenger car.
Credit
General Motors
1997
Hybrid drive in mass production
Toyota released the Prius on 10 December 1997. It paired a gasoline engine with electric motors and reused energy that is normally lost when the car slows down. The IEEE, an engineering society, named it the world's first mass-produced hybrid vehicle in a 2024 milestone.
Credit
Toyota Motor Corporation
2010
Lithium-ion packs reach mass market
In December 2010 Nissan launched the LEAF with a 24 kWh pack of flat lithium-ion cells sealed in foil pouches, made by AESC, a Nissan and NEC joint venture in Zama, Japan. It became the first electric vehicle to win the European Car of the Year award in the contest's 47 years. Tesla's low-volume Roadster had already shown a pack built from 6,831 small lithium-ion cells.
global.nissannews.comglobal.nissannews.comjust-auto.comservice.tesla.com
Credit
Nissan and AESC; Tesla for the earlier Roadster pack
2015
Diesel cheat caught on road
In September 2015 the US Environmental Protection Agency (EPA) found that Volkswagen and Audi diesel cars carried a "defeat device", software that sensed an official emissions test and switched on full emissions control only during the test. On the road the cars emitted nitrogen oxides at up to 40 times the standard.
LessonLab tests can be gamed, and testing on real roads caught what the lab test missed.
Credit
Researchers at West Virginia University with the International Council on Clean Transportation (ICCT), who found it; the EPA and the California Air Resources Board, who acted
2020
Cells straight into packs
Packs used to group cells into boxes called modules before they went into the pack; cell-to-pack designs put the cells straight in. CATL showed a cell-to-pack design in 2019, and BYD launched its Blade battery in March 2020 with long, thin lithium iron phosphate (LFP) cells, a chemistry that uses iron and phosphate in place of nickel and cobalt. Researchers at Fraunhofer IKTS, the University of Münster and RWTH Aachen University took a Blade cell apart and published a comparison in 2025.
Credit
CATL; BYD
2026
Packs must not catch fire
China's mandatory standard GB 38031-2025 took effect on 1 July 2026 for newly approved models. When one cell overheats out of control, called thermal runaway, the old rule required a warning at least five minutes before fire or explosion; the new rule says the pack must not catch fire or explode at all. Models already approved must comply from 1 July 2027.
Credit
China's Ministry of Industry and Information Technology (MIIT)
Watch for
Sodium-ion cells at volume
Sodium-ion cells carry charge with sodium, a common element, in place of lithium. CATL and Changan call a Changan car with CATL's Naxtra sodium-ion cells the world's first mass-produced passenger car with sodium-ion batteries, with a 45 kWh pack, up to 400 km of range and a market launch planned for mid-2026; no report of customer deliveries was found by November 2026. The "first" is disputed: JAC's Yiwei brand handed a sodium-ion car to customers in January 2024.
Achieved whenCustomers take delivery in volume and an outside party confirms it, through registration data or an independent teardown.
Claimed by
CATL and Changan, February 2026
Solid-state cells on the road
A solid-state cell replaces the liquid inside a lithium cell with a solid. Mercedes-Benz says a lightly modified EQS with lithium-metal solid-state cells from Factorial Energy drove 1,205 km from Stuttgart to Malmö on one charge in August 2025, in its own test, and targets series production by the end of the decade.
Achieved whenA production car with solid-state cells is sold to customers and an outside party confirms the cells are solid, for example against China's draft national definition, which drops the label "semi-solid-state".
Claimed by
Mercedes-Benz with Factorial Energy, September 2025
Charging at 1.5 megawatts
BYD says its second-generation Blade battery charges from 10% to 70% in 5 minutes, from chargers that deliver up to 1,500 kW per connector at 1,000 V. For BYD's earlier 1,000 kW system, InsideEVs reporters saw more than 1,000 kW at a demonstration, an observation rather than a logged test. BYD's 2025 test car used a silicon carbide power module, the kind of power chip covered in the Note "More chips from a bigger disc".
Achieved whenAn outside tester publishes a logged charge curve from a production car at a public station showing the claimed power and times.
Claimed by
BYD, March 2026
Open
01
Disassembly maps for current packs
Add battery packs from Tesla, BYD and Volkswagen's MEB cars to the open dataset that the Karlsruhe Institute of Technology (KIT) published in August 2026, in its format and under its CC BY 4.0 license. Record every part and fastener, the order of removal and what is visible at each step, and link each entry to a public teardown photo or a video timestamp. This is desk work only.
The briefCredit · unclaimed02
Unbolting a lid never seen
A learned robot policy that removes the cover bolts from a battery-pack lid layout it was not trained on, tested only on replica lids (3D-printed, or plywood with threaded metal inserts) that copy the bolt patterns of real packs. No real or charged packs are used.
The briefCredit · unclaimed
Open 01 · the brief
Disassembly maps for current packs
The first to publish is credited on this line, and the deliverable moves from Open to Achieved.
What to build
Add battery packs from Tesla, BYD and Volkswagen's MEB cars to the open dataset that the Karlsruhe Institute of Technology (KIT) published in August 2026, in its format and under its CC BY 4.0 license. Record every part and fastener, the order of removal and what is visible at each step, and link each entry to a public teardown photo or a video timestamp. This is desk work only.
Why it is still open
KIT's dataset covers ten packs (Fiat 500e, Chevrolet Spark, Hyundai IONIQ 5, BMW 530e, Chevrolet Volt, Volvo EX30, BMW 330e, MG ZS, Mitsubishi Outlander, BMW i3) and none from Tesla, BYD or MEB cars. The EU battery passport must carry dismantling information from 18 February 2027, but only for people with a "legitimate interest", so it will not be a public dataset.
Built with what exists
KIT's dataset and format; public teardown photos and videos; a vision-language model such as Claude Fable 5.2 (see the Note "Three working devices") to draft entries from photos, with a person checking each one.
First step
Download KIT's dataset and rebuild the IONIQ 5 entry from public photos only.
Done looks like
First, rebuild KIT's IONIQ 5 entry from public photos alone and match at least 90% of its fasteners. Then publish at least three new packs, with an independent reviewer agreeing with at least 95% of 50 randomly chosen entries against the cited images.
Open 02 · the brief
Unbolting a lid never seen
The first to publish is credited on this line, and the deliverable moves from Open to Achieved.
What to build
A learned robot policy that removes the cover bolts from a battery-pack lid layout it was not trained on, tested only on replica lids (3D-printed, or plywood with threaded metal inserts) that copy the bolt patterns of real packs. No real or charged packs are used.
Why it is still open
A University of Colorado team's RAPID system (March 2026, revised October 2026) removed top-cover fasteners on one full-size pack, with success from 57% to 97% depending on the method, and the BiHAND system removed bolts from one retired pack. Neither shows a policy carrying over to a different pack design, and the RAPID authors write that disassembly of EV battery packs "remains largely manual".
Built with what exists
An SO-101 arm with LeRobot v0.7.0 (see the Note "No download"); a robot model that learns from a few demonstrations, such as NVIDIA GR00T 2 (see the Note "Five demonstrations per task") or Runway Praxis-1 (see the Note "Open robot model weights"); a small powered screwdriver on the arm; a color-and-depth camera; bolt layouts from public photos and KIT's dataset. Robot models that learn a task from a few demonstrations are what bring this within reach of a small team.
First step
Print one small replica lid with M3 screws that copies a published pack-cover pattern, record five demonstrations with the SO-101 leader arm, then train and measure.
Done looks like
Five replica lids, trained on three and tested on the two unseen ones, with at least 90% of fasteners removed over 20 runs per unseen lid and no more than five demonstrations per new lid; video, logs and code published so someone else can rerun it.