BRENNEN

Industries / Transport and vehicles / Automotive

Paint

The paint shop cleans the bare body, dips it in a primer bath that is laid on by electric current, then sprays a color layer and a clear top layer, baking the body between steps.

7

Milestones achieved, from 1924 to 2022.

2

To watch for: announced, not yet confirmed outside.

2

Open deliverables. Nobody has shipped them.

The road

AchievedWatch forOpen

Achieved

  1. 1924

    Lacquer that dries fast

    DuPont and General Motors turned a nitrocellulose lacquer into Duco, a spray-on car finish. It was first shown on Oakland cars at the New York Automobile Show in December 1923, and Oakland painted all seven of its 1924 touring car models with it. It replaced varnishes that were brushed on in more than a dozen steps with long drying periods between coats.

    sciencehistory.org

    Credit

    DuPont and General Motors

  2. 1963

    Primer laid on by current

    In electrocoating, or e-coat, the whole body is dipped in a water-based paint bath and an electric current deposits primer on the metal, including inside closed sections. George Brewer led this work at Ford from the late 1950s, and PPG dates its own e-coat work to 1963. In 1976 PPG introduced the first cathodic electrocoat primer for cars, by the US Environmental Protection Agency's account.

    theaic.orgppg.comepa.gov

    Credit

    George E. F. Brewer at Ford; PPG

  3. 1969

    First paint robot sold

    Trallfa, a wheelbarrow maker in Norway, built a spray-painting robot to keep workers away from the dangerous chemicals in paint. Its first prototype was finished in 1967, and the first commercial unit went to the Swedish bathtub maker Gustavsberg in 1969. ASEA, which later became ABB, took over Trallfa's robot division between 1985 and 1989.

    tekniskmuseum.no

    Credit

    Ole Molaug and Trallfa

  4. 1986

    Water-based color coat

    BASF researchers in Würzburg developed a waterborne basecoat, a color layer that uses water in place of most of its solvent, which cuts the fumes counted as volatile organic compounds (VOCs). Opel approved it for its Bochum production lines in December 1986.

    emerald.com

    Credit

    BASF; Opel

  5. 2002

    One oven removed

    Mazda finished developing its Three Layer Wet Paint System in 2002. It applies primer, color and clear coat while each is still wet, so the bake after the primer is dropped. Mazda says the system cut paint-shop VOC emissions by 45% and carbon dioxide by 15%, and that it runs in all its paint shops in Japan and overseas.

    newsroom.mazda.com

    Credit

    Mazda

  6. 2020

    Two-tone paint without tape

    Painting a car in two colors used to need masking tape laid by hand and a second pass through the booth. Overspray-free applicators lay paint in sharp-edged strips, like an inkjet printer, so no tape is needed. The trade magazine Oberfläche describes BMW's use of Dürr's EcoPaintJet, shown to the trade press at the end of 2020, as the first series production process for an overspray-free contrast finish, and Mercedes-Benz began using ABB's PixelPaint at Sindelfingen in May 2025.

    oberflaeche.detherobotreport.com

    Credit

    Dürr and BMW; ABB and Mercedes-Benz

  7. 2022

    Robots fix paint defects

    Small flaws in the top coat, such as dust specks, were long sanded and polished out by skilled workers. Since March 2022 BMW's Regensburg plant has used robots to sand and polish them in series production, and in 2025 3M and General Motors installed a robotic repair system at GM's Spring Hill, Tennessee plant.

    autocarpro.inassemblymag.com

    Credit

    BMW Group; 3M and General Motors

Watch for

  1. Paint booths instead of lines

    Dürr says CEER, Saudi Arabia's electric car brand, will get the first full version of its "paint shop of the future", in which bodies go to flexible booth boxes instead of moving down a fixed line at one pace. Production there is due in the fourth quarter of 2026.

    Achieved whenCEER paints production bodies in the box-based shop and an outside visitor or trade publication confirms series operation.

    durr.com

    Claimed by

    Dürr, January 2026

  2. Paint shop without fossil fuel

    BMW says the paint shop at its plant in Debrecen, Hungary, runs without oil or gas in normal operation, and that using renewable electricity there cuts carbon dioxide-equivalent emissions by up to 12,000 tonnes a year. Series production of the iX3 was set to begin there in late October 2025.

    Achieved whenAn independent party, such as an auditor or a Hungarian emissions filing, confirms a full year of paint-shop operation without fossil fuel.

    newsroom.bmwgroup.comelectrive.com

    Claimed by

    BMW Group, September 2025

Open

  1. 01

    Measured paint-defect benchmark

    A public dataset of paint flaws (dirt specks, craters, runs, orange peel, scratches) on real painted panels. Photograph each flaw under fixed light, measure its diameter with a USB microscope and its height or depth with a dial gauge, and label its type. Report how well a detector trained on panels from one source works on panels from another. Panels come from salvage yards and body-shop scrap, so no spraying is needed.

    The brief
    Credit · unclaimed
  2. 02

    Spray paths from CAD, tested

    An open pipeline that takes a car-body surface, plans the paths a spray gun should follow, and predicts how even the paint film will be using a simple spray-deposit model. Check the model on a tabletop rig: a low-cost arm moves a hobby airbrush loaded with water-based ink over paper laid on a 3D-printed quarter-scale hood, and a flatbed scanner measures the ink density.

    The brief
    Credit · unclaimed

Open 01 · the brief

Measured paint-defect benchmark

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

A public dataset of paint flaws (dirt specks, craters, runs, orange peel, scratches) on real painted panels. Photograph each flaw under fixed light, measure its diameter with a USB microscope and its height or depth with a dial gauge, and label its type. Report how well a detector trained on panels from one source works on panels from another. Panels come from salvage yards and body-shop scrap, so no spraying is needed.

Why it is still open

The best-documented public set found, Roboflow's "Paint Defect Combine" (1,338 images, 12 classes), has no measurements, and its detector reached 67.2% mAP@50, a standard detection score, which Roboflow calls moderate. Plants run their own inspection systems and keep the data.

roboflow.com

Built with what exists

A monitor-and-camera deflectometry rig; a USB microscope; a dial gauge; an open labeling tool such as CVAT; an open-source object detector.

  1. First step

    Collect ten scrap panels and mark, photograph and measure 50 flaws. Before going further, read the NCAT12-DET paper (IEEE Access, 2024) to make sure it does not already cover this.

  2. Done looks like

    At least 1,000 measured flaws from at least three separate panel sources, under an open license, with a published table of same-source and cross-source accuracy that someone else can reproduce from the released code.

Open 02 · the brief

Spray paths from CAD, tested

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

An open pipeline that takes a car-body surface, plans the paths a spray gun should follow, and predicts how even the paint film will be using a simple spray-deposit model. Check the model on a tabletop rig: a low-cost arm moves a hobby airbrush loaded with water-based ink over paper laid on a 3D-printed quarter-scale hood, and a flatbed scanner measures the ink density.

Why it is still open

A January 2026 paper by Nagai and colleagues says paint path design for car-body robots "remains a time-consuming manual task for engineers", and its code is not linked. The public PaintNet dataset holds expert paths for general objects, not car bodies, and has no film-thickness measurements.

arxiv.orgarxiv.org

Built with what exists

The DrivAer research car body from the Technical University of Munich; ROS-Industrial's open Noether path planner; a low-cost arm such as the SO-101 with Hugging Face's LeRobot software (see the Note "No download"); AI agents that write robot programs (see the Note "Readable robot programs"); a hobby airbrush with water-based ink only; a flatbed scanner.

  1. First step

    Request the DrivAer CAD files from TU Munich, run Noether on a hood mesh, and spray five straight airbrush passes on paper to fit the deposit model.

  2. Done looks like

    For one DrivAer hood, published code produces paths whose simulated film thickness is within 20% of target over at least 90% of the area, and ten filmed tabletop runs compare measured ink density with the simulation, with the error tally published.