Industries / Transport and vehicles / Automotive
Stamping and body
Presses squeeze flat steel or aluminum sheet between shaped steel tools called dies to make panels, and the body shop joins those panels, and now large castings, into the bare car body, called the body-in-white.
7
Milestones achieved, from 1914 to 2020.
1
To watch for: announced, not yet confirmed outside.
2
Open deliverables. Nobody has shipped them.
The road
AchievedWatch forOpen
Achieved
1914
All-steel bodies from presses
Edward G. Budd's company in Philadelphia made car bodies entirely of pressed steel, and Dodge Brothers bought them for the car it launched in 1914. Car bodies have been made with large presses and dies ever since.
Credit
Edward G. Budd and engineer Joseph Ledwinka of the Budd Company; John and Horace Dodge
1922
The body carries the load
The Lancia Lambda, shown in Paris in October 1922, had no separate rigid frame. Its body shell carried the car's weight and loads, a design called a unitary or monocoque body, and Stellantis's heritage site calls it the first car built without a conventional rigid chassis. Citroën's Traction Avant, unveiled in April 1934, used an all-steel monocoque body.
Credit
Vincenzo Lancia; Citroën, with Joseph Ledwinka of Budd
1960
Die changes cut to minutes
In 1960 Toyota installed fourteen 600-ton presses from Danly at its Motomachi plant. Swapping one set of dies for another fell from hours to about fifteen minutes in the 1960s and about three minutes in the 1970s, by the historian Christoph Roser's account. Shigeo Shingo, who taught Toyota's engineers, named the method single-minute exchange of die (SMED), meaning a change in under ten minutes.
LessonFast die changes let one press line make many different parts in small batches instead of storing large piles of each.
Credit
Toyota; Shigeo Shingo
1984
Hot-stamped boron steel
In press hardening, also called hot stamping, a blank of boron steel is heated until soft, then formed and cooled inside the die, so it comes out very strong. Norrbottens Järnverk in Luleå, Sweden, developed the process, and it first went into cars as side-impact door beams in the 1984 Saab 9000. By the 2005 Volkswagen Passat, about 19% of the body-in-white by weight was press-hardened steel.
Credit
Norrbottens Järnverk AB; Saab
1994
Aluminum body in volume
The 1994 Audi A8 had an aluminum frame with large aluminum panels that carry load, which Audi calls the Audi Space Frame. Audi gives the body's weight as 249 kg and calls the A8 the first large-volume production car with a self-supporting aluminum body.
Credit
Audi
2015
Aluminum pickup and repair costs
Ford moved its F-150 pickup to an aluminum body. In low-speed crash tests by the Insurance Institute for Highway Safety (IIHS) in July 2015, repairs cost 26% more than on the steel truck. Later insurance-claims data from the Highway Loss Data Institute (HLDI) found the aluminum truck's claim costs lower than the old model's, and HLDI credited Ford's subsidies for repair tools and training.
LessonA new body material works only once the repair trade is equipped for it.
Credit
Ford; measured by IIHS and HLDI
2020
One casting replaces welded floor
Tesla made the Model Y rear underbody from large aluminum castings where the Model 3 had 70 welded parts, and in early 2021 said a single-piece rear casting from a 6,000-ton press was in volume production. An independent teardown by MarkLines confirms a cast rear structure in the Xiaomi SU7, and Volvo began building the EX60, its first car with such a casting, in April 2026. Tesla dropped a plan to cast its whole underbody in one piece, Reuters reported in May 2024.
LessonLarge castings remove parts and welds, but very large single castings raise cost and risk.
repairerdrivennews.commarklines.comcnbc.comrepairerdrivennews.com
Credit
Tesla; later Xiaomi and Volvo
Watch for
Ford's two-casting pickup
Ford says two large aluminum castings, which it calls unicastings, replace 146 structural parts in its coming midsize electric truck, and let the front and rear be built on separate lines. Ford says more than 5,000 had been cast at its Shelbyville Technical Center by October 2026, ahead of a 2027 launch.
Achieved whenProduction trucks with the two castings are on sale and an outside teardown or repair-industry report confirms the structure.
Claimed by
Ford, August 2025 and October 2026
Open
01
Read the die spotting print
An open tool that turns a photo of a spotting print into a contact map lined up with the part's CAD model, with the percentage of surface in contact. A spotting print is the blue mark left where the upper and lower die touch the panel; toolmakers read it by eye and grind the die by hand until contact is even. Make the prints on a bench rig, not a press: two mating blocks, thin aluminum sheet, engineer's blue, a bench vise, and pressure-indicating film as a second record. Shims of 0, 0.05 and 0.1 mm create known gaps.
The briefCredit · unclaimed02
Press-panel defect benchmark
A public dataset of real stamped panels with surface defects such as dents, low spots and sink marks, each defect's depth measured, plus a baseline detector. Image the panels with deflectometry: a monitor shows moving stripes, and a camera records how their reflection bends over a dent. Use new replacement fenders and doors and glossy scrap panels.
The briefCredit · unclaimed
Open 01 · the brief
Read the die spotting print
The first to publish is credited on this line, and the deliverable moves from Open to Achieved.
What to build
An open tool that turns a photo of a spotting print into a contact map lined up with the part's CAD model, with the percentage of surface in contact. A spotting print is the blue mark left where the upper and lower die touch the panel; toolmakers read it by eye and grind the die by hand until contact is even. Make the prints on a bench rig, not a press: two mating blocks, thin aluminum sheet, engineer's blue, a bench vise, and pressure-indicating film as a second record. Shims of 0, 0.05 and 0.1 mm create known gaps.
Why it is still open
Spotting is reported to take 70 to 80% of die tryout, the stage of getting a new die to make good parts, and a German toolmaker said in November 2025 that manual work is "still necessary". Simulation tools reduce engineering hours, but in one AutoForm case study on-site spotting time did not change. A 2020 lab method for decoding blue prints, by Zabala and colleagues at Mondragon University, has no released tool.
formingworld.comformingworld.combbr.newsebiltegia.mondragon.edu
Built with what exists
A phone or machine-vision camera with a color reference card; OpenCV for image alignment and color thresholds; the Mondragon method as a baseline; pressure-indicating film; optionally a 3D scanner. No new robot or AI model is needed.
First step
Make five prints on two flat steel blocks with a 0.05 mm shim, photograph them under fixed light, and write to the Mondragon authors to ask whether their code is available.
Done looks like
At least 30 rig prints across the three shim settings, each paired with its pressure-film record, and a published table of agreement between the tool's contact map and the film's, with code and images public so a second person can rerun them.
Open 02 · the brief
Press-panel defect benchmark
The first to publish is credited on this line, and the deliverable moves from Open to Achieved.
What to build
A public dataset of real stamped panels with surface defects such as dents, low spots and sink marks, each defect's depth measured, plus a baseline detector. Image the panels with deflectometry: a monitor shows moving stripes, and a camera records how their reflection bends over a dent. Use new replacement fenders and doors and glossy scrap panels.
Why it is still open
The public stamping dataset found in this research, OSPD (2024), covers punched holes only, and its defects were drawn in by computer. Commercial inspection systems such as ZEISS ABIS III keep their data private.
Built with what exists
A spare monitor and a machine-vision camera; the deflectometry method of Arnal and colleagues (Polytechnic University of Valencia, 2017) as a reference; a dial indicator for depth; an open labeling tool such as CVAT; an open-source object detector.
First step
Buy two used doors from a salvage yard, build the monitor-and-camera rig, and check that it finds dents you have marked and measured.
Done looks like
At least 500 labeled defects on at least 20 panels, each with a measured depth, under an open license, and a published table of the baseline detector's recall for defects 0.05 mm deep and deeper.