BRENNEN

Industries / Food, farming and forestry / Forestry and logging / Timber and sawmills

Panels and engineered wood

Gluing wood veneers, strands, chips or whole boards into sheets and beams that are larger, straighter or steadier than a sawn board.

7

Milestones achieved, from 1901 to 2018.

2

To watch for: announced, not yet confirmed outside.

2

Open deliverables. Nobody has shipped them.

The road

AchievedWatch forOpen

Achieved

  1. 1901

    Glued beams patented

    Otto Hetzer obtained a patent for building straight timber beams from many thin boards glued together, and later patented curved laminated arches, according to WoodSolutions, the Australian wood industry's technical body. This is glulam, short for glued laminated timber: a beam that can be longer, deeper or more curved than any one tree allows. By 1922 glulam building was documented in at least 14 countries. In 1934 Max Hanisch designed a school gymnasium in Peshtigo, Wisconsin, which WoodSolutions calls the first US building framed in structural glulam, after engineers at the US Forest Products Laboratory tested the design.

    woodsolutions.com.au

    Credit

    Otto Hetzer; Max Hanisch; the US Forest Products Laboratory

  2. 1905

    Plywood from Douglas fir

    Portland Manufacturing Company, a box and barrel maker in Portland, Oregon, made three-ply panels from Douglas fir veneer to show at the Lewis and Clark Exposition. Plywood is a panel of thin wood sheets, called veneers, glued with the grain of each layer at right angles to the next. The Oregon Encyclopedia calls these panels the first plywood made from a softwood. Thomas Autzen showed them at the fair and persuaded door and cabinet makers that they were a cheaper material.

    oregonencyclopedia.org

    Credit

    Portland Manufacturing Company, run by Gustav Carlson, and Peter and Thomas Autzen

  3. 1934

    Glue that survives rain

    Shortly before Christmas 1934, Harbor Plywood Corporation of Aberdeen, Washington, announced Douglas fir plywood bonded with a waterproof phenolic resin, a synthetic glue set by heat in a press. Earlier panels used animal and casein glues, which fail when wet. Production of the panel, sold as Super Harbord, began in January 1935, and exterior plywood went on to siding, boat planking and rail car linings. A 1942 US Commercial Standard set the tests a panel must pass to be called "Exterior".

    sumnerhistoricalsociety.com

    Credit

    chemist James Nevin and his group at Harbor Plywood, with Michel Pasquier, and Archie Knauss of the US Forest Products Laboratory, who helped solve the warping caused by hot pressing

  4. 1961

    Panels from aspen wafers

    Wizewood Products started Canada's first waferboard plant in Saskatchewan in September 1961, according to the Encyclopedia of Saskatchewan. Waferboard is pressed from thin wafers of wood bonded with resin, so it could use aspen, then a little-used tree. MacMillan Bloedel bought the plant in 1965 and doubled its output in 1968 and 1969. Its successor later closed the plant and built a mill in Hudson Bay, Saskatchewan, making oriented strand board (OSB), in which long strands are laid in crossing layers.

    esask.uregina.ca

    Credit

    Wizewood Products; MacMillan Bloedel

  5. 1994

    Cross-laminated timber

    In 1994 Gerhard Schickhofer presented a thesis at Graz University of Technology in Austria that "paved the way" for Brettsperrholz, cross-laminated timber (CLT), by the account of Swedish Wood, the Swedish sawmill industry's trade body. CLT is a solid panel of boards glued in layers, each layer at right angles to the next, large enough to form whole walls and floors. With a grant from sawmills in Styria, he and three sawmill owners developed the product and founded the company KLH Massivholz.

    swedishwood.com

    Credit

    Gerhard Schickhofer, Graz University of Technology and Styrian sawmills

  6. 2016

    A US limit on formaldehyde

    Formaldehyde is a gas given off by the urea-formaldehyde glues in many indoor panels, and the International Agency for Research on Cancer rated it "probably carcinogenic to humans" in 1995. A 2010 US law set emission limits for hardwood plywood, particleboard and medium-density fiberboard (MDF, a panel pressed from wood fibers) at California's levels, from 0.05 ppm for hardwood plywood to 0.13 ppm for thin MDF, and the Environmental Protection Agency (EPA) published its final rule on 12 December 2016. Since 22 March 2019, such panels sold in the US must be certified by a third party and labeled.

    epa.govlaw.cornell.edupublications.iarc.who.int

    Credit

    US Congress, EPA and the California Air Resources Board

  7. 2018

    A CLT floor panel falls

    On 14 March 2018, two layers of a seven-layer CLT floor panel came unglued and fell 14 ft (4.3 m) at Peavy Hall, a building under construction at Oregon State University, and no one was hurt. The investigators agreed that preheating the wood at the maker, D.R. Johnson Wood Innovations, made the glue cure too early, and Engineering News-Record reported that 45 panels not yet installed had to be replaced. APA, the US engineered wood association, had certified the maker in 2015 as the first US producer under the CLT standard PRG 320. The maker stopped preheating and now cuts sample cores each day from every billet, the large panel later trimmed to size.

    LessonA standard that tests finished panels can miss a change in how they are made between audits; APA said PRG 320 does not address preheating because performance standards look at end results.

    enr.com

    Credit

    Oregon State University, APA and D.R. Johnson Wood Innovations

Watch for

  1. Densified wood at scale

    InventWood says its Superwood, ordinary timber treated with chemicals and then compressed so its cellulose fibers bond more tightly, has about 50% more tensile strength than steel and about 10 times steel's strength for its weight, and is Class A fire rated. It said its first commercial plant, in Frederick, Maryland, would begin making batches in summer 2025, starting with facade boards. Liangbing Hu of the University of Maryland refined the method from a 2018 process and licensed it to the company. TechCrunch reported no outside testing.

    Achieved whena laboratory with no tie to the company publishes strength and fire tests on boards from the production line.

    techcrunch.com

    Claimed by

    InventWood and its chief executive Alex Lau, May 2025

  2. Plywood glue from lignin

    Latvijas Finieris, which the EU's Circular Bio-based Europe partnership calls the EU's largest birch plywood producer, leads the VIOBOND project. It aims to replace 70% of the phenol and formaldehyde in its plywood glue with lignin, the natural binder in wood, recovered at a biorefinery. A resin factory is being built in Riga, Latvia, with trials set for summer 2026, and a small share of fossil-based ingredients is still needed.

    Achieved whenplywood made with the 70% lignin resin is on sale and an outside laboratory publishes its bond strength and formaldehyde emissions.

    cbe.europa.eu

    Claimed by

    Latvijas Finieris and the Circular Bio-based Europe Joint Undertaking, September 2025

Open

  1. 01

    Tap-testing CLT glue bonds

    A tool that taps a CLT panel at points on a grid, records how the panel rings, and maps zones where a glue line between layers is likely weak, so that whole panels can be checked without cutting. Its map is checked with a delamination test, the standard soak-and-dry test on cut sections that shows whether glue lines open up.

    The brief
    Credit · unclaimed
  2. 02

    Densified wood, tested outside

    A public set of strength, hardness and fire tests on densified wood boards bought on the open market, run by a laboratory with no tie to the maker, with raw data and photos of every broken specimen.

    The brief
    Credit · unclaimed

Open 01 · the brief

Tap-testing CLT glue bonds

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

A tool that taps a CLT panel at points on a grid, records how the panel rings, and maps zones where a glue line between layers is likely weak, so that whole panels can be checked without cutting. Its map is checked with a delamination test, the standard soak-and-dry test on cut sections that shows whether glue lines open up.

Why it is still open

Makers check bonds by cutting sample cores from billets, as D.R. Johnson began doing daily after Peavy Hall. A 2026 study in BioResources found that damaged glue bonds lower a CLT panel's stiffness and natural frequencies, and computer models could locate the damage, but in experiments the natural variation of wood limited how well it could be found. An Oregon State University course project published in June 2026 tried to predict delamination test results from ultrasound sent through CLT and found that no method, deep learning included, did significantly well on its data. Searches of Crossref and GitHub in November 2026 found no whole-panel bond tester in use.

enr.comdoi.orggithub.com

Built with what exists

An impact hammer with a force sensor, or a small solenoid that taps on command; contact microphones or accelerometers; Python with SciPy and scikit-learn; and small test panels glued in a workshop with deliberately starved or pre-cured glue zones.

  1. First step

    Glue three small three-layer panels, one sound and two with planted bad zones, tap each on a 10 cm grid and compare the recordings.

  2. Done looks like

    On at least 20 test panels with planted weak zones, the tool's map checked against delamination tests on cut sections, with the share of weak zones found and the false-alarm rate published.

Open 02 · the brief

Densified wood, tested outside

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

A public set of strength, hardness and fire tests on densified wood boards bought on the open market, run by a laboratory with no tie to the maker, with raw data and photos of every broken specimen.

Why it is still open

TechCrunch's May 2025 report gives InventWood's strength figures as the company's own and mentions no outside testing. A Crossref search in November 2026 found no independent test of the product.

techcrunch.com

Built with what exists

Production boards, a universal testing machine at a university wood laboratory, and published methods for testing small clear specimens of timber.

  1. First step

    Ask the maker or a distributor for production boards and the company's own data sheet, and book time on a university testing machine.

  2. Done looks like

    Tensile strength, bending strength and hardness for at least 30 specimens cut from at least three boards, with the mean and spread set beside the company's figures.