BRENNEN

Industries / Food, farming and forestry / Forestry and logging / Timber and sawmills

Log sorting and scanning

Measuring each log as it reaches the mill, judging its volume and quality, and sorting it into piles for the saws.

4

Milestones achieved, from 1825 to 2017.

2

To watch for: announced, not yet confirmed outside.

2

Open deliverables. Nobody has shipped them.

The road

AchievedWatch forOpen

Achieved

  1. 1825

    Logs measured by rule

    Edward Doyle published a log rule, a formula that turns a log's small-end diameter and length into the board feet of lumber it should yield (a board foot is a piece 12 inches square and 1 inch thick); the oldest surviving copy is an 1837 edition. J. M. Scribner published another rule in 1846 and Judson F. Clark wrote the International rule around 1900. A Purdue University bulletin counts more than 95 log rules used in the United States and Canada, and says the Doyle rule "seriously under scales small logs and over scales large logs".

    LessonA volume rule decides who gains on every log sale, so its errors are paid by the buyer or the seller.

    extension.purdue.edu

    Credit

    Edward Doyle, J. M. Scribner and Judson F. Clark

  2. 2008

    Boards traced to logs

    Researchers at Luleå University of Technology in Sweden matched sawn boards back to the logs they came from using only scanners the sawmill already ran: an X-ray log scanner at the log sort and a camera scanner where green boards are sorted. They called the method fingerprint traceability, because the spacing of each log's knots works like a fingerprint. At a Scots pine sawmill in northern Sweden, more than 95% of the boards were matched to the right log. By 2021 Microtec was selling fingerprint matching to sawmills, including Cascade Hardwoods in Chehalis, Washington.

    traguiden.sewoodbusiness.ca

    Credit

    Jens Flodin, Johan Oja and Anders Grönlund, Luleå University of Technology

  3. 2010s

    CT scanning at line speed

    Computed tomography (CT) is the X-ray method hospitals use to build a 3D image from many angles. Microtec of Brixen, Italy, built a log CT scanner that runs at production speed: its staff scanned logs at 120 m per minute in 2012, and in 2017 a paper by Microtec staff in Annals of Forest Science called it "the first industrial X-ray CT scanner". The paper's sawing simulation found value gains of up to 20% from choosing each log's rotation from the CT image, a figure from Microtec's own staff. Trade press reported CT Log purchases by Cascade Hardwoods in Washington in 2021 and by J.D. Irving in New Brunswick, for installation in early 2024.

    annforsci.biomedcentral.comtimberprocessing.com

    Credit

    Microtec, where Federico Giudiceandrea led the scanner's development with Enrico Ursella

  4. 2017

    Lasers outmeasure the rules

    Forest Service scientists scanned 32 red and white oak logs with a laser scanner and sawed them in a computer simulator. The lumber sawn in the simulator ran from 31.9% less to 159.4% more than the common log rules predicted, depending on the rule and the log. The authors note that laser scanners "are installed in many hardwood mills", measure logs to 0.01 inch or better, and that the rules still in use were written more than 100 years ago.

    LessonA mill can now measure a log's true volume in seconds, yet logs are still bought and sold by rules written for a tape and a scale stick.

    fs.usda.gov

    Credit

    R. Edward Thomas and Neal D. Bennett, USDA Forest Service Northern Research Station

Watch for

  1. Scanners taught by CT

    Microtec says it trains the AI models in its two-source X-ray log scanner, the Logeye 302, on 3D data from its CT Log, and that this gives "unprecedented accuracy" in estimating a log's shape under the bark and has "significantly enhanced" how the scanner identifies knot types. It also links each board back to its log through the mill and uses the match to train its board scanners.

    Achieved whena study by someone other than Microtec publishes the under-bark diameter error and knot-type accuracy of a CT-trained X-ray scanner against logs measured by hand.

    stories.microtec.eu

    Claimed by

    Microtec, May 2026

  2. Neural networks inside CT

    Finnos, which grew out of the X-ray scanner maker Bintec, says its Neuro CT is "the world's first neural network-based CT scanner specifically developed for the wood industry", with deep learning models that find knots and density changes inside each log before the first cut. The article gives no accuracy figures, and Microtec's datasheet calls its own CT Log the "world's only computed tomography scanner for logs".

    Achieved whenan outside study compares the knots Neuro CT reports with the knots found in the sawn boards and publishes the match rate.

    woodandpanel.comnukor.co.za

    Claimed by

    Finnos, in Wood & Panel, October 2025

Open

  1. 01

    Hardwood log grades from photos

    A phone app that photographs a hardwood log from four sides, finds the surface defects that lower its grade, such as knots, bumps, holes and seams, and assigns a US Forest Service factory log grade (Factory 1, 2 or 3).

    The brief
    Credit · unclaimed
  2. 02

    Log stiffness by phone, tested

    A field test of a phone as a log stiffness meter. The phone records the ring of a hammer tap on a log's end and finds its first resonant frequency, which gives the log's acoustic velocity, the speed of sound along it (twice the log's length times that frequency). Sound travels faster in stiffer wood, so a mill could sort logs into stiffness classes before sawing them into structural lumber.

    The brief
    Credit · unclaimed

Open 01 · the brief

Hardwood log grades from photos

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

A phone app that photographs a hardwood log from four sides, finds the surface defects that lower its grade, such as knots, bumps, holes and seams, and assigns a US Forest Service factory log grade (Factory 1, 2 or 3).

Why it is still open

Hardwood logs are graded by eye, which Forest Service scientists say takes more time and skill than scaling alone. The industry has no single grading system: the Forest Service adopted its log grades in 1952, but a 2019 Forest Products Journal article says they never took hold in the hardwood lumber industry, so mills grade by their own rules. The Forest Service built a laser scanner to find surface defects on logs, and an open set of 600 photos with every knot outlined on 15 logs was published in October 2026, but a search of GitHub, Hugging Face, Zenodo and OpenAlex found no tool that assigns log grades from photos.

fs.usda.govdoi.orgzenodo.org

Built with what exists

A recent phone camera, the WoodKnots-600 photo set on Zenodo, an image model such as YOLO or Segment Anything, or a small open vision model such as Liquid AI's LFM3, which its maker says can be fine-tuned on one graphics card (see the Note "One GPU to fine-tune"), and the Forest Service's published hardwood log grade rules.

  1. First step

    Photograph 30 logs on a hardwood mill's deck that a grader has already graded, and outline their defects.

  2. Done looks like

    200 logs graded by the app and by two experienced log graders working apart under the Forest Service rules, with the app's agreement with the graders published next to the graders' agreement with each other.

Open 02 · the brief

Log stiffness by phone, tested

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

A field test of a phone as a log stiffness meter. The phone records the ring of a hammer tap on a log's end and finds its first resonant frequency, which gives the log's acoustic velocity, the speed of sound along it (twice the log's length times that frequency). Sound travels faster in stiffer wood, so a mill could sort logs into stiffness classes before sawing them into structural lumber.

Why it is still open

Acoustic sorting of logs works with dedicated tools. A University of Georgia study measured 87 tree-length loblolly pine logs with a HITMAN HM200 from Fibre-gen and found that log velocity explained about half the variation in the stiffness of the lumber sawn from them (R² = 0.53). Mississippi State's Smart Thumper app already measures stiffness this way on sawn timber, and a 2021 test against a commercial grading tool found it reliable below 2,000 Hz, a range long logs fall in, but that test used timber pieces, not logs. A search of Crossref and GitHub found no phone test on logs.

annforsci.biomedcentral.comdoi.org

Built with what exists

Smart Thumper, or a phone's microphone with an open audio library such as librosa to find the frequency peak; a rubber mallet; a tape measure; and an HM200 or similar tool to compare against.

  1. First step

    Tap 10 logs of known length, record each tap on a phone, and compare the frequency peak with the dedicated tool's reading for the same log.

  2. Done looks like

    App velocities within 3% of the dedicated tool's on at least 50 logs, and the app's stiffness classes checked against the stiffness of the sawn boards measured by a grading machine or a bending test.