BRENNEN

Industries / Food, farming and forestry / Forestry and logging / Timber and sawmills

Drying

Taking water out of green lumber, in the open air or in a heated chamber called a kiln, so that it stops shrinking, resists decay and weighs less to ship.

5

Milestones achieved, from 1917 to 2006.

1

To watch for: announced, not yet confirmed outside.

2

Open deliverables. Nobody has shipped them.

The road

AchievedWatch forOpen

Achieved

  1. 1917

    A kiln built on measurement

    Harry Tiemann's book The Kiln Drying of Lumber (1917) came out of his work at the US Forest Products Laboratory (FPL) in Madison, Wisconsin, which had studied lumber drying since it opened in 1910. A kiln is a closed room where heat, humidity and moving air are controlled to dry wood. By FPL's own account in its Dry Kiln Operator's Manual (1991), Tiemann's work produced "the first lumber dry kiln design", and his book "can really be considered the first drying manual". FPL's later manuals, from 1961 on, descend from it.

    research.fs.usda.gov

    Credit

    Harry D. Tiemann, Forest Products Laboratory

  2. 1919

    Airplane wood dried in weeks

    During the First World War a shortage of air-dried wood forced the United States to kiln-dry almost all of its airplane wood straight from the green state, which Tiemann called "a complete reversal of established practice". Air-drying Douglas fir wing beams took 12 to 18 months; kilns did it in 18 to 24 days. FPL strength tests found that properly kiln-dried wood was as strong, tough and stiff as the best air-dried wood, while England and France still specified against kiln-drying airplane wood.

    LessonBad drying can weaken wood with no defect the eye can see, so the drying process itself has to be measured and controlled.

    ntrs.nasa.gov

    Credit

    Harry D. Tiemann and the Forest Products Laboratory, in NACA Report 65 (1919)

  3. 1970

    Dry lumber gets a number

    The US softwood lumber standard PS 20-70 set separate sizes for dry and green lumber under 5 inches thick, so that seasoned and unseasoned lumber would be the same size once in use. Under the standard, lumber is dry at a moisture content of 19% or less, meaning the water weighs no more than 19% of the dry wood, and it is stamped S-DRY; lumber surfaced wetter is stamped S-GRN.

    LessonWood shrinks as it dries, so a board's size means little unless its moisture is stated with it.

    nist.gov

    Credit

    US Department of Commerce and the American Lumber Standard Committee

  4. 2002

    Heat that kills pests

    The International Plant Protection Convention (IPPC) adopted the standard now called ISPM 15 in March 2002. It requires wood packaging such as pallets and crates moved between countries to be treated and marked, and its heat treatment holds the wood at 56 °C or more for at least 30 minutes through its whole thickness, which sawmills and pallet makers do in kilns. Pests were the reason: the US Department of Agriculture says the Asian longhorned beetle, first found in Brooklyn, New York, in 1996, most likely arrived in wood packaging from Asia.

    LessonThe other main treatment, methyl bromide gas, depletes the ozone layer, and the IPPC now asks countries to replace or reduce it.

    fao.orgaphis.usda.gov

    Credit

    the IPPC's Interim Commission on Phytosanitary Measures

  5. 2006

    Lumber that moves through

    Andy Pollard of Pollard Lumber in Appling, Georgia, rebuilt an aging 80 ft kiln by adding 80 ft to each end, making a direct-fired kiln three times as long that dries lumber continuously rather than one batch at a time. He patented it, and USNR, a sawmill equipment maker, built it under a royalty deal as the "counter-flow" continuous dry kiln. Within several years USNR had sold about two dozen, to companies including Rex Lumber, Canfor and West Fraser, by the account of Timber Processing editor Rich Donnell.

    timberprocessing.com

    Credit

    Andy (Levi A.) Pollard, Pollard Lumber, and USNR

Watch for

  1. Lab-tested AI kiln control

    A controller that combines neural networks with fuzzy logic adjusted temperature in a laboratory hot-air drying chamber while drying ayous wood. Against standard controllers, the authors report 23.7% less energy, 18.4% shorter drying and 31.2% fewer defects, from their own tests under controlled conditions.

    Achieved whensomeone other than the authors runs it on full loads in a working kiln and reports energy, drying time and defects against the kiln's usual control.

    bioresources.cnr.ncsu.edu

    Claimed by

    Jingkuo Zhang and co-authors, Applied Technology College of Soochow University, China, in BioResources, April 2026

Open

  1. 01

    A learning kiln controller, measured

    A controller for a small kiln that sets heat, venting and humidity from sensors inside the load, run side by side with the kiln's usual fixed schedule on matched loads of the same species and thickness.

    The brief
    Credit · unclaimed
  2. 02

    A public kiln charge dataset

    An openly licensed set of kiln charges from working mills, each with species, thickness, green weight, schedule, temperature and humidity logs, drying time, and the moisture of every board as measured afterward by the planer mill's in-line meter, with a baseline model that predicts drying time and the share of boards still above target.

    The brief
    Credit · unclaimed

Open 01 · the brief

A learning kiln controller, measured

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

A controller for a small kiln that sets heat, venting and humidity from sensors inside the load, run side by side with the kiln's usual fixed schedule on matched loads of the same species and thickness.

Why it is still open

The 2026 study that reports energy and defect savings tested its controller only in a laboratory drying chamber. Searches of kiln makers and research found no published trial on full loads in a working kiln.

bioresources.cnr.ncsu.edu

Built with what exists

Halko, an open-source system for controlling and monitoring wood-drying kilns on Raspberry Pi and ESP32 boards, which switches power through Shelly relays; temperature, humidity and pin-type wood moisture sensors; a small dehumidification or solar kiln of the kind woodworkers buy, with its own over-temperature cut-out left in place; Python for the model.

github.com

  1. First step

    Install Halko on a Raspberry Pi in an existing small kiln and log one full load on its usual schedule as the baseline.

  2. Done looks like

    At least five pairs of matched loads, each reported with energy in kilowatt-hours per cubic meter, days to target moisture, the spread of final moisture measured on oven-dried samples, and the share of boards with checks (surface cracks) counted by someone who does not know which controller dried them.

Open 02 · the brief

A public kiln charge dataset

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

An openly licensed set of kiln charges from working mills, each with species, thickness, green weight, schedule, temperature and humidity logs, drying time, and the moisture of every board as measured afterward by the planer mill's in-line meter, with a baseline model that predicts drying time and the share of boards still above target.

Why it is still open

Models of kiln time and final moisture are trained on private mill records. One public project that predicts kiln-drying time from 166 industrial batches of mahogany and teak does not publish its data because it is "confidential operational company data". A search of GitHub and Hugging Face found no open dataset of kiln charges.

github.com

Built with what exists

Kiln controller logs, planer moisture-meter exports, Python with pandas and XGBoost, and Zenodo or Hugging Face to host the data.

  1. First step

    Write the column list and a plan for removing mill names, then ask one mill or a university kiln for twelve months of records.

  2. Done looks like

    At least 200 charges from at least two mills released under an open license, and a model whose error in drying hours, and in the share of boards above target moisture, is reported on charges held back from training.