Industries / Government, education and community / Nonprofits / Standards bodies
Certification
This work checks that a product, a company's management system or a factory meets a standard and says so in a certificate, and it checks the checkers: certification bodies test, inspect or audit, and accreditation bodies assess the certification bodies.
5
Milestones achieved, from 1985 to 2012.
1
To watch for: announced, not yet confirmed outside.
2
Open deliverables. Nobody has shipped them.
The road
AchievedWatch forOpen
Achieved
1985
One report, many countries
Electrical products once had to be tested again in every country where they were sold. In 1985 the IEC, the international body that writes electrical standards, merged its work with the CEE, the International Commission on Rules for the Approval of Electrical Equipment, founded in 1929, to form the IECEE. Its CB Scheme ("CB" stands for certification body) lets a test report and certificate issued by one national certification body be accepted by the others without retesting. It was modelled on European schemes, CCA and HAR (for cables), and CCA in turn on a Nordic agreement to accept each other's test results that began in 1939. By 2025 the scheme had 53 member countries, 94 or 95 national certification bodies and about 600 test laboratories, and issued about 120,000 certificates a year to more than 15,000 manufacturers, according to Nemko, a Norwegian certification body that takes part, and a March 2025 account in pv magazine.
Credit
the IEC and the CEE; the Nordic test bodies behind the 1939 agreement
1993
One mark, several routes
The European Community's "new approach" of 7 May 1985 limited its product laws to essential safety requirements and left the technical detail to voluntary standards: national authorities must presume that a product made to a harmonized standard meets the law. A Council decision of 22 July 1993 (93/465/EEC) then set out the procedures, called modules, by which a maker shows conformity, and the rules for the CE marking that follows. They run from module A, internal production control, in which the manufacturer checks its own product and declares it compliant, to modules in which a notified body, a testing or certification organization named by a member state, examines a design type, tests products or audits the factory's quality system. Each product law chooses which modules it allows.
LessonUnder module A no outside body sees the product, so the same CE mark can rest on a maker's own declaration or on a notified body's examination.
Credit
the Council of the European Communities
1998
Accreditors accept each other
Accreditation is the check, by a national accreditation body, that a certification body is competent and impartial. The International Accreditation Forum (IAF) was formed in 1998, at a time when ISO's management system standards, the EU's new approach and the new World Trade Organization were spreading. Its Multilateral Recognition Arrangement (MLA) admits an accreditation body only after a peer evaluation by other members; once admitted, a signatory must recognise certificates issued by bodies that any other signatory has accredited. By the end of 2025 the MLA had 90 accreditation body signatories and covered 4 main scopes and 36 sub-scopes. On 1 January 2026 the IAF and ILAC, the body of laboratory accreditors, were replaced by a single organization, Global Accreditation Cooperation Incorporated, which took over both arrangements.
Credit
the IAF's member accreditation bodies
2010
One accreditor per country
EU Regulation 765/2008, adopted on 9 July 2008 and applied from 1 January 2010, requires each member state to appoint a single national accreditation body, run on a not-for-profit basis as a public authority activity. The body may not compete with certification bodies or with other national accreditation bodies, and may not offer consultancy or own a stake in a certification body. The regulation gives its reason: competition between accreditors "could lead to the commercialisation of their activity, which would be incompatible with their role as the last level of control in the conformity assessment chain". It aims for one accreditation certificate to be enough across the Union.
Credit
the European Parliament and the Council of the EU
2012
Certified three weeks before
On 11 September 2012 a fire at the Ali Enterprises garment factory in Karachi, Pakistan, killed 258 people and injured 32, by the count of the European Center for Constitutional and Human Rights (ECCHR). About three weeks earlier RINA Services, an Italian certification company, had certified the factory to SA8000, a workplace standard written by Social Accountability International that covers health and safety among other conditions. According to ECCHR, many windows were barred, emergency exits were locked and the building had only one unobstructed exit. A complaint against RINA to Italy's OECD contact point, filed in September 2018, led to a mediated agreement under which RINA would pay US$400,000 to survivors and bereaved families and revise its certification system; the complainants signed in March 2020, but RINA refused to sign in autumn 2020.
LessonA certificate covers only what the audit looked at, and an audit against a social standard did not catch locked fire exits.
Credit
ECCHR, the Ali Enterprises Factory Fire Affectees Association and Pakistan's National Trade Union Federation, for the case record
Watch for
One accreditation arrangement
Global Accreditation Cooperation Incorporated says that from 1 January 2026 its single Multilateral Recognition Arrangement covers the scopes of the ILAC arrangement for laboratories and the IAF arrangement for certification bodies, that existing accreditations stay recognised during a transition, and that the ILAC and IAF marks stay valid "for as long as required until full adoption" of its new mark. It says the change will reduce duplicated effort and make accredited results "easier to trust".
Achieved whenall former signatories have signed the new arrangement, the old marks are withdrawn, and a regional accreditation group or a regulator outside the organization reports that certificates are being accepted on the new basis with no gaps in scope.
Claimed by
Global Accreditation Cooperation Incorporated, January 2026
Open
01
Certificates against safety inspections
A public table that matches the garment factories covered by the International Accord's safety inspections in Bangladesh and Pakistan to the public list of SA8000-certified organizations, and compares the fire, electrical and structural hazards that Accord engineers recorded in factories holding a social certificate at the time of inspection with those in factories that did not.
The briefCredit · unclaimed02
Notified bodies in recall alerts
A coded table of every Safety Gate alert for personal protective equipment (PPE) since the EU's PPE Regulation applied on 21 April 2018. Each alert gets the product's risk category under the regulation (Category I, which the maker assesses alone under module A; Categories II and III, which need an EU type-examination by a notified body), whether the alert reports a missing, invalid or misused notified-body certificate, and whether the four-digit notified-body number it cites is listed for PPE in NANDO, the EU's database of notified bodies.
The briefCredit · unclaimed
Open 01 · the brief
Certificates against safety inspections
The first to publish is credited on this line, and the deliverable moves from Open to Achieved.
What to build
A public table that matches the garment factories covered by the International Accord's safety inspections in Bangladesh and Pakistan to the public list of SA8000-certified organizations, and compares the fire, electrical and structural hazards that Accord engineers recorded in factories holding a social certificate at the time of inspection with those in factories that did not.
Why it is still open
Evidence on certified factories is case by case. The Clean Clothes Campaign's 2019 report "Fig Leaf for Fashion" gathered cases such as Ali Enterprises, Rana Plaza and the 2017 boiler explosion at the Multifabs factory in Bangladesh, each of which had been "assessed and declared safe" by auditing firms, but it counts no factories beyond its cases. A recent study by Debanjan Das and Mehnaz Fatima Monamy coded the corrective action plans, the lists of required repairs, of all 646 Accord-certified factories in Bangladesh and counted 18,432 safety flaws (44.4% electrical, 40.2% fire, 15.4% structural), but it did not compare factories by social certificate, and a search found no study that has.
cleanclothes.orgecchr.eucitedrive.cominternationalaccord.orgsaasaccreditation.org
Built with what exists
The International Accord's public factory pages, inspection reports and corrective action plans; Social Accountability International's list of SA8000-certified organizations; Python with a fuzzy name-matching library such as RapidFuzz, with every proposed match checked by a person; a language model to pull hazard counts out of report PDFs, with a person checking a sample.
First step
Download the SA8000 list for Bangladesh and Pakistan, try to match 50 names to the Accord's factory list, and record how many match cleanly.
Done looks like
Every Accord-covered factory marked as matched or unmatched to the SA8000 list, with two people agreeing on at least 95% of 200 rechecked matches; the median number of hazards per factory at first inspection, by type, for certified and uncertified factories, with confidence intervals; the code and the match file published.
Open 02 · the brief
Notified bodies in recall alerts
The first to publish is credited on this line, and the deliverable moves from Open to Achieved.
What to build
A coded table of every Safety Gate alert for personal protective equipment (PPE) since the EU's PPE Regulation applied on 21 April 2018. Each alert gets the product's risk category under the regulation (Category I, which the maker assesses alone under module A; Categories II and III, which need an EU type-examination by a notified body), whether the alert reports a missing, invalid or misused notified-body certificate, and whether the four-digit notified-body number it cites is listed for PPE in NANDO, the EU's database of notified bodies.
Why it is still open
Safety Gate, the EU's alert system for dangerous non-food products, recorded 4,671 alerts in 2025, the most in any year since it began in 2003; its annual report ranks alerts by product type, not by how the product's conformity was assessed. Intertek, a testing company, tallied the 164 PPE alerts of 2020 and found the most common problem was that the PPE "has not been certified by the appropriate notified body", in 76 of them, but that count covers one pandemic year, does not split alerts by risk category and does not check the cited bodies in NANDO. A search found no study comparing alerts by conformity route.
Built with what exists
The Safety Gate alert database and its weekly reports; NANDO; the text of Regulation (EU) 2016/425; a language model to draft the category and certificate codes from each alert's text, with two people checking; Python with pandas.
First step
Pull 100 recent PPE alerts and count how many mention the product's certificate or notified body at all, to see whether the alert text can carry the study.
Done looks like
Every PPE alert from 21 April 2018 onward coded, two coders agreeing on at least 90% of 100 records they both code, and a published table giving, for each category, the number of alerts and the share whose text reports a certificate problem or cites a notified-body number not listed for PPE.