BRENNEN

Industries / Transport and vehicles / Shipbuilding and repair

Steel cutting and welding

Shipyards cut steel plate into parts and weld the parts into panels and hull structures, the work that turns flat plate into a ship.

7

Milestones achieved, from 1920 to 2000.

2

To watch for: announced, not yet confirmed outside.

2

Open deliverables. Nobody has shipped them.

The road

AchievedWatch forOpen

Achieved

  1. 1920

    A hull with no rivets

    Until about 1920, ship plates were joined by rivets, hot metal pins hammered through overlapping plates. Cammell Laird of Birkenhead installed arc welding equipment in 1917 and in 1920 launched the Fullagar, a 150-foot (46 m) coaster of 420 gross register tons whose hull was welded throughout. Lloyd's Register surveyed her during construction and classed her with the notation "Electrically Welded, Subject to Biennial Survey-Experimental," under provisional welding rules it had published in 1918. The Lloyd's Register Foundation calls her "the world's first fully welded ocean-going ship." In 1924 she ran aground loaded with coal; her hull buckled but stayed watertight and her welds did not fail. Yards were slow to follow: riveters called welding "sealing wax," yards were laid out for riveting, and welding became standard only during the Second World War.

    Lessona new joining method spreads only when a classification society (the body that sets and checks a ship's construction rules) writes rules for it and ships built under those rules prove themselves in service.

    heritage.lrfoundation.org.uk

    Credit

    Cammell Laird; Lloyd's Register

  2. 1943

    Welded ships crack

    US yards welded 2,580 Liberty ships, 414 Victory ships and 530 T2 tankers between 1941 and 1946. On 16 January 1943 the T2 tanker Schenectady broke in two at the Kaiser Company's outfitting dock in Portland, Oregon, a few days after her sea trials. A Board of Investigation reviewed 4,694 welded ships from the wartime program and found that 970 had cracked. It concluded that the steel specifications then in force were "not sufficiently selective to exclude" steel that turns brittle in cold water, and that joint design and weld quality mattered. By the early 1950s a Charpy test value (the energy needed to snap a small notched bar) was used to specify tougher ship steel.

    Lessonwelding made hulls one continuous piece, so a crack that once stopped at a riveted seam could now run around the whole ship; the steel has to be chosen for that.

    twi-global.com

    Credit

    US Coast Guard Board of Investigation; account published by TWI

  3. 1960

    Computers lay out the cuts

    Shipyards once drew hull lines full size on a mould-loft floor and made wooden templates to mark each plate by hand. Thomas Hysing and colleagues at the Central Institute for Industrial Research in Oslo (now SINTEF) began work on numerical control for cutting torches in 1958 and installed a prototype at the Aker Stord yard in 1960. Their Autokon software described hull surfaces mathematically and told a machine how to cut and shape each plate; Aker and Fred Olsen founded Shipping Research Services in 1967 to sell it worldwide. In 1963 a Todd Shipyards study for the US government set out the same plan: replace manual lofting with "mathematical lofting" and numerically controlled flame and plasma cutting.

    sintef.noagris.fao.org

    Credit

    Thomas Hysing and SI/SINTEF (Autokon); Todd Shipyards (1963 US study)

  4. 1980

    A small weld fails

    On 27 March 1980 the semi-submersible accommodation rig Alexander L. Kielland capsized in a storm on the Ekofisk field in the North Sea; 123 of the 212 people on board died. Norway's commission of inquiry (NOU 1981:11) found that a fatigue crack (a crack that grows a little with each load cycle) began at a small fillet weld fixing a hydrophone, a sonar fitting, into one of the braces holding the rig's columns together. The brace parted, the other braces failed in turn, and the rig lost a support column and capsized within 20 minutes. A metallurgical study by Almar-Naess, Moan and colleagues found poor welding and poor material in the hydrophone tube, and a design fatigue life for that weld that was "inadequate." The Norwegian Maritime Directorate ordered floating units off Norway checked for cracks and required them to stay afloat after losing a column.

    Lessona minor fitting welded onto a main structural member can start the crack that sinks the whole structure, so every attachment needs a fatigue check and inspection.

    kielland.industriminne.nokielland.industriminne.noosti.gov

    Credit

    Norwegian commission of inquiry; Almar-Naess, Moan, Haagensen and Lian (1982)

  5. 1996

    Friction stir welded panels

    Friction stir welding joins metal without melting it: a spinning tool is pressed into the joint and stirs the softened metal of both parts together. TWI invented and patented it in 1991 in Cambridge, UK. Because the heat input is low, the panels distort little. Its first commercial use was hollow aluminum panels for freezing fish on fishing boats. Marine Aluminium in Haugesund, Norway, then made about 1,700 friction stir welded aluminum panels, with 110 km of weld, for ship decks and structures from 1996 to 1999, by TWI's count.

    twi-global.com

    Credit

    TWI (invention); Marine Aluminium (production)

  6. 1997

    Robots weld the hull

    Odense Steel Shipyard's Lindø yard in Denmark built much of its automation around robots for A.P. Møller's container ships. Maritime Reporter reported in April 1998 that about 14 percent of the hull of the 6,600 TEU container ship Sovereign Maersk, delivered late in 1997, had been assembled with robot welding machines, and that the yard planned robots for about 25 percent of hull and cargo-section welding by 2000.

    magazines.marinelink.com

    Credit

    Odense Steel Shipyard (A.P. Møller group)

  7. 2000

    Lasers replace the panel line

    Meyer Werft in Papenburg, Germany, researched laser welding in a national project from 1994 to 1998, and in 2000 removed its conventional panel line completely and replaced it with laser-hybrid welding, which pairs a laser beam with an arc in one pass. Waterborne, the European maritime research platform, reports that the yard roughly cut straightening work on distorted welds by about 30 percent, and quotes Meyer Werft saying it doubled or tripled welding speed. A second line for 30 m by 25 m flat sections followed around 2010.

    Lessonthin decks warp when welded, and the cheapest straightening is the heat that is never put in.

    waterborne.eu

    Credit

    Meyer Werft

Watch for

  1. Humanoid welders for shipyards

    HD Hyundai's shipbuilding arm HD KSOE and HD Hyundai Robotics signed a memorandum with the US firm Persona AI and Vazil Company in May 2025 to build two-legged humanoid robots that weld inside ships, targeting prototypes by the end of 2026 and field testing and commercial use from 2027. In March 2026 the partners signed a joint development agreement; HD KSOE will train the robots on welding data collected at its yards. No production weld by the robot has been reported.

    Achieved whena humanoid welds joints on a ship under construction and the yard's customer or a classification society reports how many of its welds passed inspection.

    en.portnews.rucyprusshippingnews.com

    Claimed by

    HD Hyundai and Persona AI, May 2025 and March 2026

  2. AI welding at HII yards

    HII, the largest US Navy shipbuilder, announced its High-Yield Production Robotics (HYPR) program on 20 April 2026 with Path Robotics (robotic welding) and GrayMatter Robotics (surface preparation and coating). HII plans proof-of-concept demonstrations in 2026 and a full pilot in 2027, aiming at "fewer labor hours per hull, more predictable schedules." The release gives no measured results.

    Achieved whenthe 2027 pilot's labor hours per hull are published and checked by an outside party such as the Navy or the US Government Accountability Office (GAO).

    hii.com

    Claimed by

    HII, April 2026

Open

  1. 01

    Taught welds in mock cells

    A public test of teaching a robot arm to follow the weld seams inside a ship's double-bottom cell (one of the box-like spaces between the outer and inner bottom, walled in by girders and floors), from a handful of demonstrations. Build a scale mock-up of one cell from a published midship drawing, mark its seams, and have the robot trace each seam with an unpowered torch or a pen, so no arc is struck.

    The brief
    Credit · unclaimed
  2. 02

    Distortion atlas for thin panels

    An open dataset that links how thin steel panels were welded (plate thickness, stiffener spacing, weld process, weld order and heat input) to the warping measured on them afterwards with a 3D scanner, and a model trained on it that predicts a new panel's warping before it is welded.

    The brief
    Credit · unclaimed

Open 01 · the brief

Taught welds in mock cells

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

A public test of teaching a robot arm to follow the weld seams inside a ship's double-bottom cell (one of the box-like spaces between the outer and inner bottom, walled in by girders and floors), from a handful of demonstrations. Build a scale mock-up of one cell from a published midship drawing, mark its seams, and have the robot trace each seam with an unpowered torch or a pen, so no arc is struck.

Why it is still open

The largest yards are still at the demonstration stage. HII plans its first proof-of-concept demonstrations in 2026 and a pilot in 2027, and HD Hyundai's welding humanoid is a prototype; neither has published a success rate. On Hugging Face, hobby datasets show welding motions taught to small arms (for example 8 recorded demonstrations on an SO-101 arm), but none is scored in ship-block geometry.

hii.comhuggingface.co

Built with what exists

An open robot model such as NVIDIA GR00T 2, which by NVIDIA's own test learns many tasks from five demonstrations (see the Note "Five demonstrations per task"); Hugging Face LeRobot to record demonstrations and train (see the Note "No download"); a low-cost six-axis arm or a used industrial arm; a depth camera; the cell drawn in free CAD such as FreeCAD.

  1. First step

    Draw one double-bottom cell at 1:4 scale from a published midship section and build it from plywood.

  2. Done looks like

    The mock cell's drawings published, 20 seams of at least three joint types, and a filmed, public tally of 20 attempts per joint type after one and after five demonstrations, scoring an attempt a success when the tool stays within 2 mm of the seam line along its whole length.

Open 02 · the brief

Distortion atlas for thin panels

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

An open dataset that links how thin steel panels were welded (plate thickness, stiffener spacing, weld process, weld order and heat input) to the warping measured on them afterwards with a 3D scanner, and a model trained on it that predicts a new panel's warping before it is welded.

Why it is still open

Thin decks still warp and are still straightened by hand with heat; even Meyer Werft's laser-hybrid line cut straightening work by only about 30 percent, by Waterborne's account. Researchers at Bauhaus-Universität Weimar, LUT and Aalto published open software in 2025 that fits surfaces to scans of distorted ship deck panels, to measure the warping after the fact; it does not come with weld records or predict warping before welding.

waterborne.euresearch.aalto.fi

Built with what exists

A handheld or phone-based 3D scanner, open point-cloud tools (CloudCompare, Open3D), the shop's weld records, and a gradient-boosting or small neural model.

  1. First step

    Ask a local steel fabricator or boatyard to let you scan ten panels before and after welding, and record how each was welded.

  2. Done looks like

    At least 100 welded panels scanned and released under an open license with their weld data, and a model that predicts each held-out panel's largest out-of-plane deflection within 1 mm.