Industries / Industrial equipment and services / Industrial services / Rope access
Training and certification
Training and certification covers how a person learns rope access, is tested by someone other than their employer, and keeps the right to work, along with the laws that say when ropes may be used at all.
7
Milestones achieved, from 1998 to 2021.
1
To watch for: announced, not yet confirmed outside.
2
Open deliverables. Nobody has shipped them.
The road
AchievedWatch forOpen
Achieved
1998
France declines a rope trade
A French deputy, Philippe Auberger, told the employment ministry that firms doing rope work were growing fast but were threatened because the law did not cover their methods. In its answer of 2 March 1998 the ministry said the decree of 8 January 1965 allowed personal protection, such as a harness, only for very short jobs of under a day or for minor work, where protection for everyone, such as a scaffold or guardrail, was technically impossible. It refused to create a protected route into the trade, citing the European rule that collective protection comes first, and argued that any jobs created would be offset by jobs lost at scaffold and lift makers.
LessonRope access entered law as a last resort, allowed only where safer equipment cannot be used, and Europe's 2001 directive kept that principle.
Credit
France's Ministry of Employment and Solidarity; written question no. 8426
2000
California writes rope rules
Section 3270.1 of California's General Industry Safety Orders, filed on 4 August 2000 and in force from 3 September 2000, set rules for rope access in dams, spillways, buildings, bridges and power plant penstocks (the large pipes that carry water to turbines). Ropes are allowed only where other access is not feasible or would raise the risk. The employer must keep a written code of safe practices that includes rescue, retrain each worker every year with a hands-on check, have a qualified person inspect the equipment before and after each day's use, use anchors that hold twice the highest expected load, keep at least two trained workers on site, and give the backup line its own anchor. SPRAT says its documents paved the way for this rule, which it calls one of the first laws in North America to allow rope access, and that Alberta and New York City followed.
Credit
California Occupational Safety and Health Standards Board; SPRAT
2001
Europe requires two ropes
Directive 2001/45/EC of 27 June 2001 set the conditions for rope access across the European Union. Ropes may be used only where a risk assessment shows the work can be done safely and safer equipment is not justified. There must be at least two separately anchored ropes, a working rope and a backup rope, with a self-locking device that stops a fall if the worker loses control; tools must be tied on; the work must be planned so a worker can be rescued at once; and workers must be trained in rescue. A single rope is allowed only where a second rope would make the job more dangerous. Member states had until 19 July 2004 to adopt it. Britain did so in Schedule 5 of the Work at Height Regulations 2005, in force from 6 April 2005, in almost the same words.
Credit
European Parliament and Council of the European Union; Britain's Health and Safety Commission
2001
US certification begins
SPRAT, formed in the mid-1990s by companies using rope access in North America, says it has certified technicians to its standards since 2001. It certifies three levels; at each, a candidate passes a written test and a practical test judged by an evaluator SPRAT appoints, not by the trainer. Its certification requirements of May 2020 make each certificate valid for three years, ask for 500 hours and six months of logged rope work before a technician moves up a level, and fail a candidate for errors such as an upside-down backup device. Outside users confirm it: the US Bureau of Reclamation's rope access climbers are SPRAT certified, and British Columbia's safety regulator names SPRAT's documents in its rules.
Credit
SPRAT
2012
An ISO rope access standard
The International Organization for Standardization (ISO) published ISO 22846, a standard for rope access in two parts: Part 1 in 2003 and Part 2 in 2012, both adopted in Britain as BS ISO standards. Britain's own code of practice, BS 7985, was reissued on 30 September 2013 with its general advice removed, so that it now only adds detail to the two ISO parts. Loui McCurley, who chaired the US committee that later wrote ANSI/ASSP Z459.1, said the US fall protection committee began to deal with rope access only after ISO 22846 was published.
Credit
ISO; BSI committee PH/5, Personal fall protection
2015
British Columbia names the schemes
Under Part 34 of British Columbia's workplace safety rules, as amended on 1 February 2015, an employer must check and record, before anyone works on ropes, that the person was trained to one of a short list of named documents, such as IRATA's code of practice or SPRAT's safe practices, and holds a valid certificate from that body. The regulator, WorkSafeBC, adds that the bodies' practices are not interchangeable: a technician certified by IRATA must follow IRATA's practices, and one certified by SPRAT must follow SPRAT's. Where the regulation sets a figure, such as the load an anchor must hold, it overrides both bodies' documents.
Credit
WorkSafeBC
2021
A US rope access standard
The American Society of Safety Professionals (ASSP) announced on 2 November 2021 that it had published ANSI/ASSP Z459.1-2021, Safety Requirements for Rope Access Systems. It requires a two-rope system, a full-body harness and self-locking connectors whose gates hold 3,600 pounds (about 16 kN). It sorts sites into simple ones, where a technician can get on and off the rope at top and bottom, and complex ones that need extra training, such as bridges where the rope is re-anchored to one side. ISHN called it the first standard of its kind; McCurley, who chaired the subcommittee, said the US fall protection committee had long had no place for rope access.
Credit
ASSP's Z359 fall protection committee; Loui McCurley
Watch for
Ontario drafts rope rules
Ontario's Ministry of Labour, Immigration, Training and Skills Development has proposed a stand-alone regulation for rope access in window washing, construction and farming, the first specific rope access rules in an Ontario safety regulation, which would also allow rope access on construction and farm sites. Workers and their on-site supervisors would need IRATA or SPRAT certification; employers would have to keep trained rescuers on site whenever ropes are in use, write rescue procedures and site work plans, and notify the ministry at least 24 hours before rope work starts; and workers would keep personal logs of their hours, signed off by supervisors. Comments closed on 21 August 2026.
Achieved whenthe regulation is filed and in force, and the ministry or an outside body reports how it is applied, such as the number of rope access jobs notified.
Claimed by
Ontario's Ministry of Labour, Immigration, Training and Skills Development, June 2026
Open
01
Map schemes clause by clause
A public table that shows, requirement by requirement, what each rulebook demands: IRATA's training scheme (TACS) and code of practice, SPRAT's two documents, ISO 22846, ANSI/ASSP Z459.1, California section 3270.1, the 2001 EU directive and British Columbia's Part 34. Rows cover hours and months before moving up a level, how often a certificate must be renewed, retraining after time off, who assesses, the smallest crew, anchor strength and rescue skills.
The briefCredit · unclaimed02
Time how fast skills fade
A bench test, run at ground level on a rope fixed to a frame at waist height, in which certified technicians rig their own descender, backup device and ascenders, then check a partner's rig that has been set up with common faults: a descender threaded the wrong way, a side plate left open, a backup device upside down, slack above the backup. Each person's errors are set against their level, logged hours and months since their last assessment.
The briefCredit · unclaimed
Open 01 · the brief
Map schemes clause by clause
The first to publish is credited on this line, and the deliverable moves from Open to Achieved.
What to build
A public table that shows, requirement by requirement, what each rulebook demands: IRATA's training scheme (TACS) and code of practice, SPRAT's two documents, ISO 22846, ANSI/ASSP Z459.1, California section 3270.1, the 2001 EU directive and British Columbia's Part 34. Rows cover hours and months before moving up a level, how often a certificate must be renewed, retraining after time off, who assesses, the smallest crew, anchor strength and rescue skills.
Why it is still open
WorkSafeBC rules that IRATA and SPRAT practices are not interchangeable, while its own anchor loads override both, so crews and clients that mix certificates need to know exactly where the documents differ. The two schemes differ even on the basics: IRATA asks for 1,000 hours on ropes at each level before the next, SPRAT for 500 hours and six months. The comparisons found are level-by-level summaries by sellers, such as MTN Shop's guide, with no clause references.
Built with what exists
The free texts (IRATA offers TACS free; SPRAT's public documents; the California, EU, British and British Columbia rule texts); paid standards (ISO 22846, Z459.1, BS 7985) cited by clause number without copying their wording; a spreadsheet; a language model to draft cells for people to check.
First step
Draft the 60 requirement rows and fill the columns for California section 3270.1 and the EU directive, the two shortest free texts.
Done looks like
60 requirements by 8 documents, every cell giving a clause number or "not addressed", checked by one IRATA Level 3 and one SPRAT Level III technician, published under an open licence with their disagreements listed.
Open 02 · the brief
Time how fast skills fade
The first to publish is credited on this line, and the deliverable moves from Open to Achieved.
What to build
A bench test, run at ground level on a rope fixed to a frame at waist height, in which certified technicians rig their own descender, backup device and ascenders, then check a partner's rig that has been set up with common faults: a descender threaded the wrong way, a side plate left open, a backup device upside down, slack above the backup. Each person's errors are set against their level, logged hours and months since their last assessment.
Why it is still open
IRATA and SPRAT certificates last three years, and IRATA requires refresher training only after 180 days off ropes. SPRAT fails a candidate at assessment for an upside-down backup device or too much slack above it, and in the 2023 Stampede case a supervisor had threaded a descender wrongly. The one measure of fading found is for wind turbine technicians on a basic height safety and rescue course: Lawani, Hare and Cameron (Safety Science, 2018) followed 30 and found their hands-on performance fell over one and three months without practice. A search found no such measure for rope access technicians.
app01.irata.orgcdn.shopify.combsee.govresearchonline.gcu.ac.uk
Built with what exists
a steel frame or a training centre's anchor beam at waist height; low-stretch rope; the devices the technicians already use; a score sheet built from SPRAT's list of fails and discrepancies; phone video; a spreadsheet.
First step
Write the list of planted faults with one IRATA Level 3 trainer and try it on ten technicians attending a refresher course.
Done looks like
At least 100 technicians at three or more training centres, each timed rigging three devices and checking five rigs with planted faults; error rates published by level, hours and months since assessment, with the spread.