BRENNEN

Industries / Construction and property / Commercial and residential construction / Roofing

Flat roofs

Flat roofs, which roofers call low-slope roofs, are the nearly level roofs of factories, stores and offices, covered by a continuous waterproof skin called a membrane that is laid over insulation on a structural deck.

7

Milestones achieved, from 1840s to 2017.

1

To watch for: announced, not yet confirmed outside.

2

Open deliverables. Nobody has shipped them.

The road

AchievedWatch forOpen

Achieved

  1. 1840s

    Felt, tar and gravel

    The built-up roof, the first membrane for flat roofs, is made of layers called plies: felt soaked in tar, stuck together with hot tar or asphalt mopped on at the roof, then covered with gravel. Sources disagree on when it began. A history course published by the Western Canada chapter of IIBEC, the institute of roof and building-enclosure consultants, lists Warren Roofing starting in Ohio in 1844 and coal tar with saturated felt in 1847. A 2004 article in IIBEC's journal Interface places the method in the middle of the 19th century, and a 2009 Interface article dates its "crude beginnings" to the 1870s, when roofers began to prefer asphalt to coal tar. In 1974 the US National Bureau of Standards (NBS, now NIST) put US use at about 30 million squares a year (a square is 100 sq ft, so about 280 million m²).

    westerncanada.iibec.orgiibec.orgiibec.orgnvlpubs.nist.gov

    Credit

    the Warren roofing business in Ohio, by IIBEC Western Canada's account; no single inventor is named in the sources read

  2. 1953

    A roof feeds a fire

    On 12 August 1953 a welder's sparks started a fire in General Motors' Hydra-Matic transmission plant in Livonia, Michigan, a building of 1.5 million sq ft (about 140,000 m²). Assembly Magazine's history says heat trapped under the unvented ceiling burned through the thin steel roof deck, and 2,000 tons of tar mopped between layers of fiberboard insulation caught fire across the roof. It puts the damage at $50 million and calls it the most destructive industrial fire in American history; a Fire Engineering article by the fire officer Francis Brannigan gives $75 million. An explanatory note in NFPA 276, the National Fire Protection Association's fire test for roof assemblies, says the asphalt roof covering melted and dripped through the deck joints and spread the fire, and that a 20 by 100 ft (6 by 30 m) test building and five large fire tests followed, from which Factory Mutual (FM), an insurer, wrote a test for roof decks. FM's Approval Standard 4450 for "Class 1" insulated steel deck roofs measures how much fuel a roof adds to a fire below it in a calorimeter that FM says it developed and has used since 1955.

    LessonA roof rated against embers from outside can still feed a fire burning under it, so the whole build-up over the deck has to be tested.

    assemblymag.comwebstore.ansi.orgfmapprovals.comfireengineering.com

    Credit

    Factory Mutual (now FM)

  3. 1962

    Roofs from rubber sheets

    EPDM is a synthetic rubber sold in wide sheets and laid in a single layer, a "single-ply" membrane, with its seams glued or taped instead of built up from mopped plies. Carlisle, its main US maker, says it first put butyl rubber sheeting made for farm use on the 190 ft (58 m) round restaurant roof at Chicago's O'Hare airport in 1961, which it calls the first rubber roof membrane, and introduced its Sure-Seal EPDM membrane in 1962. IIBEC Western Canada's history course lists an earlier neoprene rubber roof on an arena at Yale in 1957. A history by a Carlisle manager says EPDM spread in the 1970s when the oil embargo raised the price of asphalt and lowered its quality, that early glued seams lost strength under standing water, and that Carlisle's seam-related warranty claims fell 80% after it began applying seam tape at the factory, around 2005. ASTM, the standards body, publishes D4637, a specification for EPDM roof sheet.

    LessonThe seams, not the sheet, were EPDM's weak point, and moving seam work from the roof into the factory cut failures, by Carlisle's count.

    carlislesyntec.comroofingcontractor.comastm.org

    Credit

    Carlisle (Carlisle SynTec)

  4. 1974

    Criteria after two-ply failures

    In the 1960s and 1970s some makers replaced the usual four plies of light felt with two or three heavier ones, under slogans such as "One Plus One Equals Four", and many of those roofs failed, by a 2009 account in IIBEC's journal Interface. Robert Mathey and William Cullen of NBS collected samples of installed built-up roofs across the country and in November 1974 published performance criteria for bituminous membranes: minimum values for measured properties such as tensile strength, tear resistance, pliability in cold weather and thermal expansion, which a membrane needs whatever it is made of. Field surveys had found problems ranging from small adhesion faults to severe splitting of membranes. Their report said that after more than 70 years of use no required property of a built-up membrane had been specified, and that this lack was probably the largest single obstacle to bringing new kinds of roofing to market. The 2009 article calls it the first industry-accepted work of its kind.

    LessonA cheaper build can look the same on the roof and fail years later, so membranes need measured minimum properties, not only recipes.

    nvlpubs.nist.goviibec.org

    Credit

    Robert G. Mathey and William C. Cullen, US National Bureau of Standards

  5. 1998

    Ratings for cool roofs

    A cool roof reflects most sunlight and gives off heat well as infrared light, so it stays cooler in the sun and the building below needs less air conditioning. The Cool Roof Rating Council (CRRC), a nonprofit, was set up in 1998 to rate roofing products for solar reflectance and thermal emittance (how readily a surface radiates heat), measured new and again after three years of weathering at approved test farms. Since 1999, energy codes including ASHRAE 90.1, the International Energy Conservation Code and California's Title 24 have added cool-roof credits or requirements, by a 2008 review by Hashem Akbari and Ronnen Levinson of Lawrence Berkeley National Laboratory (LBNL), whose simulations had recommended that California's 2005 code require cool roofs on low-slope commercial buildings. The CRRC's directory export of 17 November 2026 lists 3,243 rated roof products.

    coolroofs.orgcoolroofs.orgheatisland.lbl.govheatisland.lbl.govportal.coolroofs.org

    Credit

    Cool Roof Rating Council; LBNL's Heat Island Group

  6. 2011

    TPO tested for heat

    TPO (thermoplastic polyolefin) is a plastic single-ply sheet whose seams are fused with hot air. IIBEC says it was used in Europe from the 1980s and reached the US market in the early 1990s, and that ASTM's first TPO standard, D6878, came only in 2003. GAF scientists Tom Taylor and Jennifer Keegan, whose company makes TPO, date the first North American TPO roof to a 1986 demonstration, write that early formulas with brominated fire retardants weathered badly, and estimate the installed area at more than 20 billion sq ft (about 1.9 billion m²) by 2020. Some roofs failed early from heat, for example next to reflective walls and equipment. In 2011 ASTM lengthened D6878's heat-aging test from 670 hours (28 days) to 5,376 hours (224 days) at 240 °F (116 °C), eight times as long, by the account of IIBEC's Technical Advisory 12. A field study by the Western States Roofing Contractors Association (WSRCA), with 16 TPO membranes from four makers installed in 2000 in four climates, found 15 performing satisfactorily after ten years.

    LessonA membrane can pass its standard and still fail where heat builds up on real roofs, and the test was lengthened only after those field failures.

    iibec.orgiibec.org

    Credit

    ASTM Subcommittee D08 and TPO makers; WSRCA for the field study

  7. 2017

    Rated roofs reflect less

    Field studies by the Midwest Roofing Contractors Association (MRCA) and the National Roofing Contractors Association (NRCA) measured the reflectance of working roofs. In Texas in 2012, 12 of 20 modified bitumen cap sheets read below their three-year CRRC ratings; in a 2015 study of 89 single-ply roofs in Chicago, Miami and Phoenix, none of the 95% confidence ranges for measured reflectance contained the CRRC rating. NRCA's magazine Professional Roofing reported in June 2017 that the researchers advise cutting three-year ratings by 0.10 for normal dirt and 0.15 for heavy dirt when sizing air conditioning or modeling energy use. LBNL's 2011 analysis of the CRRC's records found the largest losses in field-applied coatings, modified bitumen and single-ply membranes, and the smallest in factory-applied coatings and metal.

    LessonA rating made on samples at a test farm does not predict a working roof, where slope, drainage, rain and foot traffic change how much light it reflects.

    professionalroofing.netescholarship.org

    Credit

    MRCA and NRCA; Mohamad Sleiman, Ronnen Levinson and colleagues at LBNL

Watch for

  1. Roofs cooler than the air

    Passive radiative cooling films and coatings reflect nearly all sunlight and radiate heat in an infrared band that passes through the atmosphere to space, so in sunshine they can run cooler than the surrounding air. i2Cool, a Hong Kong company, presented results from three Chinese school pilots at a UNESCO-hosted conference in Paris in July 2026: roof surfaces 20.1 to 32.8 °C cooler than without its membranes and coatings, and at one school an indoor temperature 8.3 °C lower; the pilots belong to a program led by City University of Hong Kong. Separately, the US Defense Department's ESTCP program is installing a passive radiative cooling film on buildings at several bases to compare heat flow with and without it (project EW24-7969); its page says a two-week bench test at Twentynine Palms, California, reached as low as 10 °F (5.6 °C) below ambient and that the project is due to finish in 2026.

    Achieved whenAn outside party publishes a full cooling season of measured roof heat flow or cooling energy for treated and untreated roofs, compared with an ordinary white roof, and the products carry CRRC three-year aged ratings.

    onestopesg.comserdp-estcp.mil

    Claimed by

    i2Cool, July 2026, as reported by OneStop ESG

Open

  1. 01

    Seam welds graded by camera

    A camera rig that rides behind a hot-air welder and grades each TPO or PVC seam from ordinary and thermal video of the weld edge, where roofers look for a thin "sheen" or "bleed-out" of melted plastic, combined with the welder's own log of temperature and speed. With it, a public set of seams welded on a bench under good and deliberately bad conditions (too little heat, too fast, dirty or damp sheet), each later cut and peel-tested to show whether the camera was right. All welding is done on tables at ground level, on new membrane offcuts.

    The brief
    Credit · unclaimed
  2. 02

    Lab aging checked against weather

    A public tracker of the CRRC's "Rapid Ratings". The CRRC lets makers list interim values from a laboratory aging practice, ASTM D7897, which soils and weathers a sample in under a week, until the product's three-year outdoor values are measured and replace them. Saving the CRRC's free daily directory export captures both numbers for the same product when one replaces the other. The tracker records every such pair and publishes how far the lab value missed the outdoor one, by product type.

    The brief
    Credit · unclaimed

Open 01 · the brief

Seam welds graded by camera

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

A camera rig that rides behind a hot-air welder and grades each TPO or PVC seam from ordinary and thermal video of the weld edge, where roofers look for a thin "sheen" or "bleed-out" of melted plastic, combined with the welder's own log of temperature and speed. With it, a public set of seams welded on a bench under good and deliberately bad conditions (too little heat, too fast, dirty or damp sheet), each later cut and peel-tested to show whether the camera was right. All welding is done on tables at ground level, on new membrane offcuts.

Why it is still open

On roofs, seams are still checked by dragging a blunt probe along every seam edge once it has cooled for at least 20 minutes, plus test welds cut and pulled by hand each day, as Carlisle's Versico brand instructs. Leister's LQS Roofing records a welder's temperature, speed, air volume, voltage and GPS position, which shows how the machine was set, not whether the sheets bonded. The nearest roof test found is NIST's 1990 study of an ultrasonic scanner for glued EPDM seams, which judged infrared imaging impractical for that job. Thermal imaging has been tried on heat-fused waterproof sheets elsewhere: a 2024 study in Japan's Geosynthetics Engineering Journal is building a heat-transfer model to set pass-fail temperatures for welded tunnel-lining sheets, checked so far with thermocouples. GAF researchers counted a roof weld as proper when more than 70% of the bond tore through the sheet in a peel test. Searches in November 2026 found no published test of a camera grading heat-welded roof seams against peel results.

versico.comrooferscoffeeshop.comnvlpubs.nist.govjstage.jst.go.jpiibec.org

Built with what exists

A hand-held or small automatic hot-air welder, such as Leister's Triac or Uniroof; TPO and PVC membrane offcuts from a roofing supplier; a phone camera and a low-cost thermal camera module such as a FLIR Lepton on a Raspberry Pi; an open image model fine-tuned on the labeled seams; a tensile tester at a university or test lab for peel tests.

  1. First step

    Weld 30 seams at three heat settings, film each pass, and pull them on a borrowed tensile tester.

  2. Done looks like

    At least 300 bench seams, each peel-tested and scored pass or fail on the 70% tear rule, published with the camera's call for every seam; the camera catches at least 95% of the failed seams, and the miss and false-alarm counts are published.

Open 02 · the brief

Lab aging checked against weather

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

A public tracker of the CRRC's "Rapid Ratings". The CRRC lets makers list interim values from a laboratory aging practice, ASTM D7897, which soils and weathers a sample in under a week, until the product's three-year outdoor values are measured and replace them. Saving the CRRC's free daily directory export captures both numbers for the same product when one replaces the other. The tracker records every such pair and publishes how far the lab value missed the outdoor one, by product type.

Why it is still open

The CRRC states that Rapid Ratings are interim and are replaced once three-year weathering ends. Its export of 17 November 2026 marks 384 of 3,243 products with Rapid Ratings: 198 metal, 61 coatings, 52 single-ply membranes and 73 others, by this research's count. LBNL researchers built the lab practice: in their 2014 paper it reproduced in three days the CRRC's three-year values of solar reflectance for 25 products, and a 2015 study ran it in several laboratories. They also calibrated it in 2018 to roofs in Guangzhou, China, and analyzed the CRRC's outdoor results in 2011. The CRRC's own Validation Testing, from January 2025, re-tests a rated product every seven years; it does not compare the interim values with the ones that replace them, and no public comparison of the two was found.

coolroofs.orgportal.coolroofs.orgeta-publications.lbl.govapi.crossref.orgcoolroofs.orgescholarship.orgastm.org

Built with what exists

The CRRC's CSV export; a scheduled script, for example on GitHub Actions, to save it daily; Python and pandas to match product IDs; Zenodo or another open repository for the archive.

  1. First step

    Download today's export, list the products carrying Rapid Ratings, and set a daily download running.

  2. Done looks like

    An open archive of daily exports from the start date, and a table, updated monthly, of every product whose Rapid Rating has been replaced, giving the change in solar reflectance and thermal emittance; after 12 months, the share of lab values within 0.05 of the outdoor value, by product type.