BRENNEN

Industries / Health / Medical devices / Prosthetics

Powered limbs

Powered limbs carry batteries, motors and electronics: hands and arms worked by myoelectric control, which reads the small electrical signals muscles make through the skin, and knees and ankles run by microprocessors.

7

Milestones achieved, from 1960 to 2014.

3

To watch for: announced, not yet confirmed outside.

2

Open deliverables. Nobody has shipped them.

The road

AchievedWatch forOpen

Achieved

  1. 1960

    The Russian hand

    In 1955 Battye, Nightingale and Whillis showed that muscle signals could control a prosthesis. In 1960 Alexander Kobrinski and co-workers reported their work on such a hand in a paper read in Moscow. The production model that followed had surface electrodes over the forearm muscles that switched a motor to open or close the hand at a fixed speed; in 1965 D. S. McKenzie reported it being fitted to seven people with forearm amputations in a preliminary British trial, with the electronics and battery carried in packs on the body. The historian Allison Marsh calls it the first clinically significant myoelectric prosthesis. Ottobock says it brought myoelectric arms to market in 1965.

    spectrum.ieee.orgswisswuff.ch

    Credit

    Alexander Kobrinski and colleagues, Moscow

  2. 1968

    A Boston elbow, rejected

    Talks between Norbert Wiener, the founder of cybernetics, and the surgeon Melvin Glimcher led to a muscle-controlled elbow built by MIT, Harvard Medical School, Massachusetts General Hospital and the insurer Liberty Mutual, which wanted injured workers off long-term disability. Amar G. Bose and Robert W. Mann of MIT recruited the graduate students Ralph Alter and Ronald Rothschild, and the Boston Arm was shown in 1968. A 1984 case study by the US Office of Technology Assessment found the first versions "by all accounts failures": 18 were made and fitted, and every user rejected it, mostly because of the bulky battery worn on a belt. Improved versions sold in the hundreds through Liberating Technologies, and the design influenced Stephen Jacobsen's Utah Arm.

    Lessonpeople judge a powered arm by its weight and battery as much as by its control.

    spectrum.ieee.org

    Credit

    Norbert Wiener, Melvin Glimcher, Amar G. Bose, Robert W. Mann, Ralph Alter and Ronald Rothschild

  3. 1993

    Knees with a computer

    A microprocessor knee uses sensors and a small computer to change the knee's resistance during each step. Blatchford of Basingstoke, UK, says its Intelligent Prosthesis of 1993 was the first microprocessor knee on the market; it set the swing of the leg to walking speed. Ottobock calls its C-Leg, designed by the Canadian Kelly James and shown at a congress in Nuremberg in 1997, the world's first microprocessor-controlled knee joint. Outside measurements followed. In 1997 J. G. Buckley and colleagues found two of three users of the Intelligent Prosthesis used 5.6 to 9.0% less oxygen at speeds away from their normal pace, and in 2008 J. T. Kahle and colleagues reported 64% fewer falls and 59% fewer stumbles among 19 users after they moved to a C-Leg.

    blatchfordmobility.comcorporate.ottobock.comebi.ac.ukebi.ac.uk

    Credit

    Blatchford; Ottobock and Kelly James

  4. 2007

    Five fingers, five motors

    The i-LIMB from Touch Bionics of Livingston, Scotland, was described in August 2007 as the first widely available prosthetic device with five individually powered digits. Its roots go back to a programme the UK National Health Service began in 1963 for children affected by thalidomide; David Gow of NHS Lothian did the first research, and Touch Bionics was spun out of the NHS in 2003. Outside tests followed: in 2013 J. T. Belter and colleagues measured the i-Limb and five other commercial multi-finger hands.

    opedge.comebi.ac.uk

    Credit

    David Gow and Touch Bionics

  5. 2007

    One adult in four stops

    E. A. Biddiss and T. T. Chau reviewed about 200 articles on arm prostheses from 1980 to 2006, 40 of which gave rejection rates. Adults rejected body-powered arms at an average rate of 26% and electric arms at 23%; for children the figures were 45% and 35%.

    Lessonelectric arms are given up almost as often as body-powered ones, so a new arm is judged by whether people keep wearing it.

    ebi.ac.uk

    Credit

    E. A. Biddiss and T. T. Chau

  6. 2009

    Muscle patterns choose the motion

    In targeted muscle reinnervation (TMR), surgeons move the nerves that once served the lost arm onto other muscles, which then give usable signals for the missing hand and elbow. In a study at the Rehabilitation Institute of Chicago published in JAMA in 2009, five people who had TMR between 2002 and 2006 controlled a virtual arm with pattern recognition, software that learns which pattern of muscle signals goes with each movement; they completed 96.3% of elbow and wrist movements and 86.9% of hand movements within 5 seconds. Coapt, founded in Chicago in 2012, sells a pattern-recognition controller; the US Centers for Medicare & Medicaid Services created a billing code for such controllers, L6700, in January 2025, effective 1 April 2025, and in February 2025 Hanger agreed to buy Coapt.

    ebi.ac.ukcoaptengineering.com

    Credit

    T. A. Kuiken, K. B. Englehart and colleagues; Coapt, led by Blair Lock

  7. 2014

    An arm with ten motions

    On 9 May 2014 the US Food and Drug Administration (FDA) granted a De Novo request from DEKA Integrated Solutions of Manchester, New Hampshire, setting up a new class of device for its arm, which has up to 10 powered degrees of freedom (separate joint motions), more than two of which can move at once. The decision drew on a Veterans Affairs study that enrolled 36 arm users: 77% said they wanted a DEKA Arm in the future, and 7 left early, 4 of them over scheduling or repair problems.

    accessdata.fda.govaccessdata.fda.gov

    Credit

    DEKA Integrated Solutions; US Department of Veterans Affairs

Watch for

  1. Fingertips that sense objects

    Engineers at the University of Utah fitted the fingertips of a commercial TASKA hand with infrared proximity and pressure sensors, and let software close each finger to the point of contact while the user controlled the grip with muscle signals. With this shared control they report more secure and more precise grips and less mental effort, in tests with volunteers with intact arms and four people with below-elbow amputations.

    Achieved whena group outside Utah repeats the gains with more users, or a maker sells sensing fingertips and an independent test confirms them.

    pmc.ncbi.nlm.nih.gov

    Claimed by

    Marshall A. Trout, Jacob A. George and colleagues, University of Utah, December 2025

  2. Magnets instead of muscle signals

    A team at MIT reports a skin-worn array of magnetic sensors that tracks 3 mm magnetic beads placed inside muscle, so a prosthesis can follow how the muscle moves. In a first study in people it says this gave more accurate and responsive control than electrodes on or in the muscle.

    Achieved whenthe work passes peer review and a group outside MIT repeats the control gains in more people.

    medrxiv.org

    Claimed by

    Christopher C. Shallal, Hugh M. Herr and colleagues, K. Lisa Yang Center for Bionics, MIT, in a preprint not yet peer reviewed, November 2025

  3. A knee after muscle repair

    The same MIT group reports that two people with above-knee amputations, after surgery to restore the paired pulling action of their remaining thigh muscles, controlled a bionic knee better when standing up from a chair and climbing stairs, gains it says training alone did not explain.

    Achieved whena peer-reviewed study in more people, with a comparison group, confirms the gains.

    medrxiv.org

    Claimed by

    T. Shu, J. McCullough, H. M. Herr and colleagues, MIT, in a preprint, August 2026

Open

  1. 01

    Delay tables for bionic hands

    A public table, for current myoelectric hands and their controllers, of the time from a muscle-like signal at the electrode to the first movement of the fingers, with closing time and grip force, measured on a bench with a synthetic signal in place of a person, in both simple two-electrode control and pattern-recognition modes.

    The brief
    Credit · unclaimed
  2. 02

    Open teardowns of bionic hands

    Published teardowns of retired myoelectric hands: how each one comes apart, photos of every layer, a table of the motors, gearboxes, battery cells, connectors and main chips with their part numbers, the parts found worn or broken, and a step-by-step guide to the commonest repair, checked by a second person on a second unit. Only retired hands are used. Any settings or usage records stored in a hand are erased unread, batteries are taken out before opening, and no repaired hand goes back into anyone's use.

    The brief
    Credit · unclaimed

Open 01 · the brief

Delay tables for bionic hands

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

A public table, for current myoelectric hands and their controllers, of the time from a muscle-like signal at the electrode to the first movement of the fingers, with closing time and grip force, measured on a bench with a synthetic signal in place of a person, in both simple two-electrode control and pattern-recognition modes.

Why it is still open

Todd R. Farrell and R. F. Weir put the best controller delay at about 100 to 125 ms, and Farrell has argued that every article on a new controller should report its delay. In 2021 A. Chadwell and colleagues at the University of Salford wrote that the actual delay of clinically prescribed prostheses was unpublished, and measured it on their participants' own devices; no model-by-model table with a method others can repeat was found.

pmc.ncbi.nlm.nih.govpmc.ncbi.nlm.nih.gov

Built with what exists

a signal generator or microcontroller playing synthetic bursts (band-limited noise shaped by an envelope, not recordings of anyone) into each electrode through a conductive gel pad; a Hall-effect sensor or a 240 frames-per-second phone camera on a finger; a logic analyser to time signal onset against motion; a grip cylinder with a load cell.

  1. First step

    Build the signal source and timing rig and measure one hand that a prosthetics school or clinic already owns, on the bench, with nobody wearing it.

  2. Done looks like

    At least six hand-and-controller pairs from at least three makers, 50 timed trials per pair and mode, with average and spread of delay, closing time and grip force; methods and raw files published; an outside lab repeats two pairs within 10 ms.

Open 02 · the brief

Open teardowns of bionic hands

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

Published teardowns of retired myoelectric hands: how each one comes apart, photos of every layer, a table of the motors, gearboxes, battery cells, connectors and main chips with their part numbers, the parts found worn or broken, and a step-by-step guide to the commonest repair, checked by a second person on a second unit. Only retired hands are used. Any settings or usage records stored in a hand are erased unread, batteries are taken out before opening, and no repaired hand goes back into anyone's use.

Why it is still open

Repairs go back to the maker. Ottobock asks clinics to send its bebionic and Michelangelo hands to its after-sales team, offers a loaner hand "depending upon availability", and gives a two-year warranty that its repair plan extends to three. In the Veterans Affairs study behind the FDA's 2014 decision on the DEKA Arm, 4 of 36 users left early over scheduling or repair problems. A web search found no published teardown or repair guide for any current myoelectric hand.

ottobock.comaccessdata.fda.gov

Built with what exists

Retired hands bought second-hand or given by clinics and schools; precision driver sets, a USB microscope, a multimeter and a bench power supply; iFixit's open format for repair guides; FreeCAD for exploded drawings; the makers' public datasheets for each part identified.

  1. First step

    Get one retired hand from a prosthetics school, take it apart on camera, and publish its parts table.

  2. Done looks like

    At least five hand models from at least three makers taken apart and published under an open licence, each with a parts table and photos; for each model, one repair guide that a second person follows on another unit, with the time it took; a table of the faults found across all units.