Industries / Health / Medical devices / Prosthetics
Braces
Bracing is the making and fitting of orthoses: braces and splints that support, correct or protect a body part, from spine braces for growing children to ankle braces and powered frames that move weak legs and arms.
7
Milestones achieved, from 1946 to 2014.
2
To watch for: announced, not yet confirmed outside.
2
Open deliverables. Nobody has shipped them.
The road
AchievedWatch forOpen
Achieved
1946
A removable brace for spines
In 1946 Walter Blount of Milwaukee described a removable brace running from the pelvis to the neck, first to hold the spine after surgery for scoliosis caused by polio, and in 1958 he and colleagues reported using it without surgery for adolescent scoliosis of unknown cause. Fayssoux and colleagues date the modern era of brace treatment from it.
LessonThe early chin rest pressed on the jaw and caused jaw deformities, so it was replaced by a pad at the throat.
Credit
Walter P. Blount and colleagues, Milwaukee
1972
Braces from standard modules
At Boston Children's Hospital, the surgeon John Hall and the orthotist William Miller stopped casting every brace to the patient: Miller made six standard sizes of plastic body module that were trimmed and padded for each child. When one patient refused the Milwaukee brace's metal uprights and neck ring, a lower brace ending under the arm was made instead, and its X-rays showed better correction than the version with the uprights.
LessonA patient's refusal led to a lower brace that corrected curves better.
Credit
John Hall and William Miller, Boston Children's Hospital
1979
A brace for nights only
Frederick Reed, a surgeon in Charleston, South Carolina, and the orthotist Ralph Hooper made a brace molded with the child bent sideways past straight, to be worn only in bed, which Fayssoux and colleagues call the first side-bending brace for night-time wear only. Night braces were designed to cut the hours spent in a brace and the embarrassment of wearing one in the day.
Credit
Frederick Reed and Ralph Hooper
2004
Brace wear decides relapse
Clubfoot, a foot turned in and down from birth, is corrected in the Ponseti method by a series of casts and then held in a foot abduction brace for two to four years. In 51 infants with 86 clubfeet, M. B. Dobbs and colleagues found that not wearing the brace as prescribed was the factor most tied to the deformity coming back, with an odds ratio of 183.
LessonA correction lasts only as long as the brace that holds it is worn.
Credit
M. B. Dobbs and colleagues
2009
A brace for running
Around 2009 the Center for the Intrepid at Brooke Army Medical Center developed the Intrepid Dynamic Exoskeletal Orthosis (IDEO), a custom carbon-fibre ankle brace whose springy strut along the shin stores and returns energy, with a four-week Return to Run training program, for service members whose badly injured legs had been saved. In a 2026 telephone survey of 145 users a mean of 90 months later, 55.2% still used it and 9.7% had chosen amputation.
LessonOf 624 people given the brace there from 2009 to 2014, 121 (19%) still had an amputation within a year, so the brace could not save every leg.
Credit
Center for the Intrepid, Brooke Army Medical Center
2013
Bracing shown to work
Whether braces stop scoliosis curves from growing was disputed. The BrAIST trial, at 25 centres in the US and Canada and funded mainly by the US National Institute of Arthritis and Musculoskeletal and Skin Diseases, was stopped early because bracing worked: 72% of braced adolescents reached skeletal maturity without a curve of 50 degrees or more, against 48% of those observed, and success rose with hours of wear, measured by temperature loggers in the braces.
LessonFewer families than expected would accept treatment by chance, so in 2009 the trial added a group who chose their treatment.
Credit
S. L. Weinstein, L. A. Dolan and colleagues
2014
Exoskeleton cleared for walking
On 26 June 2014 the US Food and Drug Administration (FDA) granted Argo Medical Technologies' ReWalk a De Novo request, the route for a device with no earlier equivalent, creating a new class named "powered exoskeleton": a motorized frame worn over the legs that lets people with spinal cord injury at levels T7 to L5 stand and walk, with a trained companion, in a rehabilitation version and a personal one. Medicare later placed personal exoskeletons under its brace benefit and from 1 April 2024 set its payment for one at $91,032, by The O&P EDGE's report of the federal fee schedule.
Credit
Argo Medical Technologies (now Lifeward); US FDA; US Centers for Medicare & Medicaid Services
Watch for
A self-balancing exoskeleton at home
The FDA cleared Wandercraft's Eve on 3 August 2026 for people with spinal cord injury at any level, to walk "hands-free, utilizing self-balancing technology, in home and community settings" on level, firm, dry surfaces with a trained companion. In Wandercraft's three studies of 39 participants with neck- and chest-level injuries, 25 non-serious adverse events related or possibly related to the device were reported. Wandercraft calls Eve the first exoskeleton cleared for personal use in the home.
Achieved whena study run outside the company reports months of home use, with falls and hours of use counted.
Claimed by
Wandercraft, August 2026
Powered arm brace on trial
Myomo sells the MyoPro, a powered elbow, wrist and hand brace that reads electrical signals from weak arm muscles and helps them move, and says it offers "increased functionality" to people with arm paralysis. It reported an average selling price of about $55,500 and a randomized trial at the University of Utah with 25 of a planned 50 people enrolled. A separate US Department of Veterans Affairs trial comparing therapy with and without the MyoPro after stroke is recruiting, with its main results due about April 2027.
Achieved whena randomized trial run outside the company reports better arm function with the brace than with therapy alone.
Claimed by
Myomo, August 2026
Open
01
AFO stiffness after long use
A bench rig that bends bought, ready-made ankle-foot orthoses (AFOs, braces that hold the ankle and foot) back and forth at the ankle on a rigid dummy leg up to a million times, measuring how stiff each one is every 50,000 cycles, and a published method and data set that others can repeat. No person wears a brace at any stage.
The briefCredit · unclaimed02
Testing stance-control knee joints
A bench test leg, a thigh and shank joined at the knee and driven through walking-like motion with stance load applied, that counts how often bought stance-control knee joints fail to lock when weight comes on or fail to unlock for the swing. These joints are used in knee-ankle-foot orthoses (KAFOs), long leg braces that keep a weak knee from buckling while letting it bend during the swing. No person wears the brace at any stage.
The briefCredit · unclaimed
Open 01 · the brief
AFO stiffness after long use
The first to publish is credited on this line, and the deliverable moves from Open to Achieved.
What to build
A bench rig that bends bought, ready-made ankle-foot orthoses (AFOs, braces that hold the ankle and foot) back and forth at the ankle on a rigid dummy leg up to a million times, measuring how stiff each one is every 50,000 cycles, and a published method and data set that others can repeat. No person wears a brace at any stage.
Why it is still open
Prosthetic feet have test standards (ISO 10328 and ISO 22675) and AFOs have none. When the same 13 carbon-fibre AFOs from Allard, Ottobock, Thuasne and Trulife were measured on five rigs, results differed by a median of 27% between rigs, and the authors call for standards. Two 2026 reviews of AFO testing say the same. Searches of the research literature and GitHub found no published record of how a commercial AFO's stiffness changes with use.
Built with what exists
A stepper or servo motor with a gearbox, a reaction torque sensor and an angle encoder, run from an Arduino or Raspberry Pi; a machined or 3D-printed dummy shank and foot; bought carbon-fibre AFOs (for example the 13 models in the 2023 study) and polypropylene ones; Python for the stiffness fits.
First step
Buy two samples of one carbon-fibre AFO, build a single-axis rig, and measure both before and after 10,000 cycles.
Done looks like
At least 10 AFO models, three samples of each, cycled to one million cycles through a fixed ankle angle range, with stiffness reported every 50,000 cycles; the rig shown to repeat a measurement on the same AFO within 5% on two days; rig drawings, code and raw data published under an open licence.
Open 02 · the brief
Testing stance-control knee joints
The first to publish is credited on this line, and the deliverable moves from Open to Achieved.
What to build
A bench test leg, a thigh and shank joined at the knee and driven through walking-like motion with stance load applied, that counts how often bought stance-control knee joints fail to lock when weight comes on or fail to unlock for the swing. These joints are used in knee-ankle-foot orthoses (KAFOs), long leg braces that keep a weak knee from buckling while letting it bend during the swing. No person wears the brace at any stage.
Why it is still open
The only counts found come from people walking on treadmills. In a 2024 study of 10 users, the joints never failed to lock, but failed to unlock on 9.9% of steps with the NEURO TRONIC and 13.9% with the E-MAG Active. Ontario's 2021 health technology assessment rated the evidence that stance-control braces beat locked ones as very low and costed a mechanical stance-control brace at C$10,784. Searches of the research literature and GitHub found no bench comparison of lock and unlock reliability across commercial joints.
Built with what exists
Aluminium or 3D-printed thigh and shank segments; a servo or stepper drive with a crank, or a used industrial robot arm, to move the knee; a load cell and spring to apply stance load at heel contact; an angle encoder and a camera to log each lock and unlock; bought stance-control knee joints, such as the two named in the 2024 study; Python to count events from the logs.
First step
Buy one stance-control knee joint, mount it between two aluminium bars, and count locks and unlocks over 1,000 cycles turned by a motor.
Done looks like
At least five joint models, each run for 10,000 simulated steps at three walking speeds and on two slopes, with published counts of missed locks and missed unlocks, video of every failure, and the rig drawings and code released; the bench unlock-failure rate for the two joints in the 2024 study set beside its 9.9% and 13.9%.