Industries / Mining and materials / Plastics and rubber
Extrusion and film
Extrusion pushes softened plastic through a shaped opening, called a die, to make long products such as pipe, cable coating, sheet and film.
7
Milestones achieved, from 1845 to 2019.
3
To watch for: announced, not yet confirmed outside.
2
Open deliverables. Nobody has shipped them.
The road
AchievedWatch forOpen
Achieved
1845
A ram coats wire
A ram extruder is a piston that pushes a batch of soft material out through a die. Tadmor and Gogos's textbook says Henry Bewley and Richard Brooman "apparently developed the first ram extruder in 1845 in England", and that such a machine insulated the first submarine cable, laid between Dover and Calais in 1851.
Credit
Henry Bewley and Richard Brooman; Charles Hancock of the Gutta Percha Company, who patented a wire-coating apparatus in 1848
1879
The screw replaces the ram
In a screw extruder, a turning screw inside a heated barrel pushes material forward without stopping, so a product can be any length. Tadmor and Gogos link "the birth of the extruder" to Mathew Gray's 1879 British patent. They also note an unproven earlier claim by A. G. DeWolfe and separate machines by Francis Shaw (1879) and John Royle (1880).
LessonWire and cable makers needed coating with no breaks, and that need moved the trade from stop-start rams to the continuous screw.
Credit
Mathew Gray
c. 1935
PVC pipe in German homes
The first PVC pipes were made about three years after the first PVC tubes of 1932, on a roll mill and a ram extruder. From 1936 to 1939, more than 400 homes in central Germany were fitted with PVC water and waste pipes. A 1990 account reported them "still in use today without any major problems".
LessonA long record in the field is what buyers of a new pipe material look for.
Credit
the German chemical industry (the source names no company)
1940s
Blown film grows from pipe
In blown film, a thin tube is extruded upward, inflated with air into a bubble, cooled and flattened into wide, thin film. A 2001 TAPPI conference paper says the method grew out of pipe extrusion in the late 1940s, once low-density polyethylene was on sale.
Credit
researchers at DuPont, ICI and Union Carbide, and the film makers Plax and Visking, per the TAPPI paper
1958
Gauges steer the die
Roy E. Lowey Jr. patented a flat die whose lip bolts are heated or cooled one at a time, so each bolt grows or shrinks and moves the die opening. His patent says the heaters can be run automatically from a beta-ray gauge, a sensor that measures sheet thickness. A 1982 patent from another company describes gauge-driven die adjustment as existing practice.
Credit
Roy E. Lowey Jr., Blaw-Knox Company (filed 1958, granted 1960)
1964
Many layers, one film
In feedblock coextrusion, several molten plastics are stacked into layers before they enter one die. One film can then combine, for example, a gas barrier with layers that keep moisture out. The Plastics Hall of Fame dates the patent to 1964. The Google Patents record shows a 1967 filing that continues 1964 and 1965 applications, granted in 1971.
Credit
Walter Schrenk and Douglas Chisholm, Dow Chemical
2019
Oxo-degradable plastic banned
Oxo-degradable plastic carries additives that make it break into tiny fragments as it oxidizes. The EU banned products made from it in Directive 2019/904 because "that type of plastic does not properly biodegrade and thus contributes to microplastic pollution".
LessonBreaking into small pieces is not the same as biodegrading.
Credit
European Parliament and Council
Watch for
Thinner stretched polyethylene film
MDO film is stretched lengthwise after it is made, which makes it thinner and stiffer. Reifenhäuser says it made "the world's first process-stable 18 µm MDO PE film", where 20 to 25 µm is usual. It says a 16 to 17 µm MDO polyethylene film can replace the 12 µm PET film in laminated packs. A pack made of one plastic is easier to recycle.
Achieved whena converter sells packs made with this film, and an outside lab or a RecyClass certificate confirms the thickness and recyclability.
Claimed by
Reifenhäuser Blown Film, June 2025
Film line tunes itself
Windmöller & Hölscher says its EASY2 Run system "maximizes line performance and output" on blown film lines at the push of a button. It says the system manages more than 1,000 production settings and moves the bubble's cooling point as room conditions change. Visitors from the University of Paderborn reported the K 2025 demonstration, and neither source gives a measured gain.
Achieved whena film producer or independent party publishes output and scrap figures from a production line, before and after.
Claimed by
Windmöller & Hölscher, October 2025
Recyclable packaging by law
The EU Packaging and Packaging Waste Regulation, (EU) 2025/40, states: "All packaging placed on the market shall be recyclable." Design-for-recycling rules apply from 1 January 2030, or 24 months after the detailed rules are adopted if that is later, and recycling at scale is required from 2035.
Achieved whenthe Commission adopts the detailed recyclability grades and film packs on sale are graded against them.
Claimed by
European Union (applies from 12 August 2026)
Open
01
Name a gel's cause
A gel is a small lump or speck in film. Build a public set of gel images in which a lab has confirmed each gel's cause: unmelted resin, cross-linked resin, burnt resin or foreign dirt. Add a baseline model that predicts the cause from the picture alone.
The briefCredit · unclaimed02
Auto-tune a desktop extruder
Software that takes a new batch of shredded recycled plastic and adjusts a desktop filament extruder's temperatures, screw speed and puller speed on its own until the filament holds its target diameter.
The briefCredit · unclaimed
Open 01 · the brief
Name a gel's cause
The first to publish is credited on this line, and the deliverable moves from Open to Achieved.
What to build
A gel is a small lump or speck in film. Build a public set of gel images in which a lab has confirmed each gel's cause: unmelted resin, cross-linked resin, burnt resin or foreign dirt. Add a baseline model that predicts the cause from the picture alone.
Why it is still open
Commercial film scanners "detect and classify defects of any type" by how they look, and a trade article on one maker's scanners does not describe them finding the cause. Testing labs still use microscopy, infrared and Raman spectroscopy and other methods to "identify chemical composition, source, and morphology of gels". A 2025 study of film defects cites "the difficulty in obtaining large annotated datasets", and its data are available only on request.
Built with what exists
Film samples (recycled polyethylene film has many gels); a high-resolution flatbed scanner or a backlit USB microscope; infrared (FTIR) or Raman time at a university or a contract lab; an open image model such as Ultralytics YOLO, or a classifier in PyTorch; Zenodo or Hugging Face to publish.
First step
Collect ten sheets of recycled and virgin polyethylene film, scan them, mark 200 gels by hand, and ask one lab for a price to test 30 of them.
Done looks like
At least 1,000 gels from at least three film sources, each with a lab-confirmed cause, in at least four classes. A held-out test set, with accuracy for each class published next to chance level, and code anyone can rerun.
Open 02 · the brief
Auto-tune a desktop extruder
The first to publish is credited on this line, and the deliverable moves from Open to Achieved.
What to build
Software that takes a new batch of shredded recycled plastic and adjusts a desktop filament extruder's temperatures, screw speed and puller speed on its own until the filament holds its target diameter.
Why it is still open
3devo's guide to its own filament maker says getting the settings right is "all about trial and error", and that recycled material typically needs "a reduction in temperatures with each recycling occurrence". Searches found automatic tuning for 3D-printer settings and offline models of filament diameter, but nothing that retunes the extruder during a run for each new recycled batch.
Built with what exists
A desktop filament extruder with an in-line diameter sensor and data logging, such as 3devo's Filament Maker; Python with an open optimization library such as BoTorch or scikit-optimize; household HDPE or PP shredded to flake. The barrel runs hot, so follow the maker's safety guidance.
First step
Run one known batch by hand and log every setting and diameter reading to a spreadsheet, as the baseline.
Done looks like
For three different recycled batches, the filament holds 1.75 mm ± 0.05 mm over 10 m within eight trial runs per batch. Every run is logged, and the tally is published next to a human operator's run count on the same batches.