Industries / Construction and property / Commercial and residential construction / Painting
Robots
This is the work of machines that spray, roll or sand walls and ceilings, inside rooms or on the outside of a building, in place of a painter on a ladder, a lift or a hanging platform.
4
Milestones achieved, from 1988 to 2026.
2
To watch for: announced, not yet confirmed outside.
2
Open deliverables. Nobody has shipped them.
The road
AchievedWatch forOpen
Achieved
1988
A robot repaints a tower
Taisei Corporation, a Japanese general contractor, built a robot to repaint the outside of the Shinjuku Center Building in Tokyo, a 54-storey tower 220 m tall finished in 1979. The robot hung on two cables from a carriage that ran along the roof, and from September 1988 it sprayed both the undercoat and the finish coat. Eight airless spray guns, which break paint into droplets by forcing it at high pressure through a small tip, worked inside a hood pressed against the wall so that the mist did not drift away, at up to 100 m² an hour. Taisei calculated that the job would take 9 months and 513 worker-days by robot, against 13 months and 1,976 worker-days for painters in three gondolas.
LessonTaisei's manual case assumed three coats and the robot case two, so the saving it reported was not measured like for like.
Credit
Taisei Corporation (Masahiro Takeno and colleagues)
2005
Few building robots last
Reviewing Japanese work at the 2005 International Symposium on Automation and Robotics in Construction (ISARC), Tatsuo Arai of Osaka University counted more than 150 robots developed for building construction since the 1980s, among them Shimizu's exterior wall spraying robot. He wrote that "there are very few successful cases" and that the main obstacle to using them was "lack of robot performance".
Lessona robot that finishes one showcase job is not yet a tool that contractors keep using.
Credit
Tatsuo Arai, Osaka University
2024
A handful on sale
Chinedu Okonkwo and Tulio Sulbaran of the University of Texas at San Antonio reviewed the autonomous painting robots sold for building work and found eight, among them MYRO, PictoBot, Okibo and Dafang's DF061. All came from young companies of 11 to 50 employees, most spray rather than roll, and their reach runs from 3.1 m to 20 m. Every speed figure in the review, such as MYRO's "about ten times faster than a human painter", is cited to the robot's maker or developer.
Lessonbuyers could compare the makers' figures but had no outside ones.
Credit
Chinedu Okonkwo and Tulio Sulbaran, University of Texas at San Antonio
2026
Field test finds slow robot
Tsung-Han Tsai, Jacob J. Lin and Shang-Hsien Hsieh tested a fully commercial painting robot in sample houses on building sites run by a general contractor in Taiwan, and reported at the ICCCBE 2026 conference. The robot could not be used straight out of the box: its settings and the paint mix had to be tuned on site. Once tuned, it kept the finish quality steady but worked slowly and used too much paint, and the authors proposed a workflow in which skilled painters adjust the paint mixture.
Lessona robot bought off the shelf still needs a painter's knowledge of paint to do the job.
Credit
Tsung-Han Tsai, Jacob J. Lin and Shang-Hsien Hsieh
Watch for
Robots sand a Netflix venue
Okibo, a robot maker based in New Jersey and Tel Aviv, says its battery-powered robots sanded and painted for the contractor Performance Contracting Inc. (PCI) on Netflix House, a 100,000 sq ft (about 9,300 m²) entertainment venue at King of Prussia, Pennsylvania. It says the job saw "a 5x increase in productivity" for Level 4 and Level 5 sanding, the two smoothest standard grades of drywall finish. In December 2025 Okibo launched the EG7+, which it says reaches 24 ft (7.3 m) and finishes an average of 1,000 sq ft (about 93 m²) an hour.
Achieved whenPCI or another party outside Okibo publishes hours, areas and finish inspections for robot-finished and hand-finished rooms on the same job.
Claimed by
Okibo, August 2025 and December 2025
A drone paints walls
Lucid Bots of Charlotte, North Carolina, added a painting module to its Sherpa drone, which was first built to wash the outsides of buildings. The drone flies on a power tether and keeps its paint reservoir on the ground, and sensors hold the nozzle at a set distance and angle from the wall while an operator steers. Lucid Bots says it reaches 160 ft (48.7 m), covers more than 200 sq ft (18.5 m²) a minute, and finishes jobs up to three times faster than traditional methods at nearly half the cost.
Achieved whena building owner or an independent tester publishes the coverage rate, film thickness and overspray measured on a paid building job, against a crew working from lifts or ropes.
Claimed by
Lucid Bots, October 2025
Open
01
Cut-in by robot arm
A robot arm that "cuts in" with a brush: it paints the straight edge where a wall meets the ceiling or the trim, without masking tape, as painters do by hand before they roll the open wall. The arm learns the stroke from a painter's demonstrations.
The briefCredit · unclaimed02
A shared test room
A public test for interior painting robots: a built room with an inside corner, an outlet box, a window opening, a door frame and a 4 m wall, and a written protocol that times each robot from unloading to clean-up and measures paint used per square meter, film thickness, missed spots and touch-up time, against a two-person crew in the same room.
The briefCredit · unclaimed
Open 01 · the brief
Cut-in by robot arm
The first to publish is credited on this line, and the deliverable moves from Open to Achieved.
What to build
A robot arm that "cuts in" with a brush: it paints the straight edge where a wall meets the ceiling or the trim, without masking tape, as painters do by hand before they roll the open wall. The arm learns the stroke from a painter's demonstrations.
Why it is still open
The robots on sale spray the open wall and leave the edges to people. Legend Robot's arm is described as covering 95% of walls and ceilings, and MYRO's users mark areas for the robot to avoid on a tablet. A search for robot cut-in work found brush-stroke research for art and edge-cleaning robots, but nothing on wall edges.
Built with what exists
A low-cost arm such as the open SO-101 or a UFactory xArm 6, with a camera on the wrist; Hugging Face's LeRobot to record demonstrations and train the arm; an open robot model such as NVIDIA's GR00T 2 or Runway's Praxis-1 (see the Notes "No download", "Five demonstrations per task" and "Open robot model weights"); a mock-up corner of drywall and pine trim; ordinary latex wall paint and a 50 mm (2 in) angled sash brush.
First step
Build the mock-up corner, have a painter cut in 50 times while a camera records the brush, and post the recordings.
Done looks like
20 filmed attempts at a 60 cm cut line by the robot and 20 by a journeyman painter, each scored from photos for the largest wander from the line in millimeters and the length of paint on the wrong surface, published with the video and the code.
Open 02 · the brief
A shared test room
The first to publish is credited on this line, and the deliverable moves from Open to Achieved.
What to build
A public test for interior painting robots: a built room with an inside corner, an outlet box, a window opening, a door frame and a 4 m wall, and a written protocol that times each robot from unloading to clean-up and measures paint used per square meter, film thickness, missed spots and touch-up time, against a two-person crew in the same room.
Why it is still open
The speed figures in the 2024 University of Texas at San Antonio review all trace back to the robots' makers or developers, and the one independent field test this research found, the 2026 Taiwan study, covered a single robot in sample houses and reports its result only in words.
Built with what exists
Standard steel studs and drywall; a wet film thickness comb, a notched gauge pressed into fresh paint; an ultrasonic coating thickness gauge such as the DeFelsko PosiTector 200, which reads paint thickness on non-metal surfaces; a scale to weigh paint pails before and after; time-lapse cameras; a spreadsheet.
First step
Write the protocol, build one 3 m by 4 m test wall with an outlet box, a window opening and an inside corner, and time one crew painting it.
Done looks like
The protocol published, and at least two commercial robots and two crews each run through the room three times, with every timing, weight and thickness reading posted as raw data.