Industries / Industrial equipment and services / Industrial services / Painting and abrasive blasting
Robots
These machines blast, wash or paint steel in place of a person holding a nozzle, carried on cranes, cables or magnetic and vacuum crawlers, often with a vacuum shroud that collects the debris at the tool.
5
Milestones achieved, from 1992 to c. 2003.
1
To watch for: announced, not yet confirmed outside.
2
Open deliverables. Nobody has shipped them.
The road
AchievedWatch forOpen
Achieved
1992
A robot blasts a tank
Researchers at the University of Texas at Austin hung a motion module from a tank's wind girder, the stiffening ring near the top, on two steel cables and moved it over the shell under computer control, with a blasting or painting head. In a 1992 demonstration it blasted and painted a test tank satisfactorily, reaching a commercial blast grade (SSPC-SP 6) at a vertical speed of 3.8 cm per second; the authors estimated 220 m² a day for a two-person crew.
Credit
C. M. Dailey, A. E. Traver, G. L. Wesley, C. T. Haas and J. T. O'Connor, University of Texas at Austin, as reported by NIOSH in 2000
1994
Crane robot strips bridge beams
North Carolina State University's Construction Automation and Robotics Laboratory, with the Federal Highway Administration and the North Carolina Department of Transportation, put a robot arm and a containment box on the end of a truck-mounted crane, so an operator on the deck could blast lead paint off the beams below. The authors say the first prototype was tested in August 1994. NIOSH researchers who watched it at a bridge test site found the arm, cameras and crane boom worked well but the containment box for sandblasting still needed improvement. A 2008 review by the University of Technology Sydney noted that it needed a CAD drawing of the bridge to work on its own and that teleoperation gave low productivity.
LessonA robot that depends on drawings and a remote operator is slower than the crew it replaces; it has to sense the structure itself.
Credit
S. J. Lorenc, B. E. Handlon and L. E. Bernold, North Carolina State University
1997
Water jets strip a carrier
The US Navy's Hull Jet 60, built by the Naval Surface Warfare Center's Carderock Division with Pratt & Whitney Waterjet Systems, held a rotating 40,000 psi (about 2,800 bar) water nozzle in a vacuum shroud on a frame at the end of a high-reach lift. In a study whose site visits ended in September 1997, NIOSH investigators watched it strip freeboard paint from an aircraft carrier to bare metal, 30 ft² (2.8 m²) in about five minutes. The Navy put its average over four demonstrations at 178 ft² (16.5 m²) an hour and said the waste from one carrier hull would fall from 6,000,000 pounds with dry grit to 100,000 pounds. The same study watched Flow International's HydroCat, a vacuum crawler, strip a 30-mil (about 0.75 mm) coating from a cargo ship's deck at 480 to 500 ft² (45 m²) an hour on 25 August 1997, with no visible emissions.
Credit
Naval Surface Warfare Center Carderock Division and Pratt & Whitney Waterjet Systems; Flow International; observations by A. Echt, K. H. Dunn and R. L. Mickelsen of NIOSH
2000
Nine prototypes, mostly flat steel
The US National Institute for Occupational Safety and Health (NIOSH) searched for automated blasting devices for steel structures and found nine, from university designs to machines on sale, including a Japanese crawler, the En-vac of MHI Marine Engineering, a Mitsubishi Heavy Industries subsidiary. They were hung from booms or cables or held to the steel by vacuum, and blasted with anything from high-pressure water to silica sand. Its February 2000 report concluded that many would cut workers' exposure to lead and silica, but that measuring how much "awaits more in-depth study", that equipment could cost more than conventional blasting, and that many were best suited to large flat surfaces such as tanks and ship hulls. Air sampling during a demonstration of one, the Auto Blaster, on a bridge mock-up found 2,800 to 10,300 µg of lead per m³ inside the containment and 2 to 5 µg/m³ outside it.
LessonMoving the operator outside the containment protected the operator; it did not make the air inside any cleaner.
Credit
Alan Echt, Kevin H. Dunn and R. Leroy Mickelsen, NIOSH (report ECTB 183-23; Applied Occupational and Environmental Hygiene, October 2000)
c. 2003
Hull robot outruns the crew
Hammelmann's Dockmaster carries an ultra-high-pressure water tool up a ship's side on a remotely controlled vehicle. Maritime Journal reported its first job in a UK yard: refitting a Royal Navy aviation training ship, where 8,000 m² of hull and topsides had to be stripped to bare metal. One operator with occasional helpers stripped about 1,000 m² per 10-hour shift while the vehicle collected the old coating and waste water, and the next month it removed 1,000 m² of coating from the bow of the Queen Mary 2 at Saint-Nazaire in 10 hours, a section manual high-pressure jetting could not do. The report says Hammelmann had built Dockmasters since 1969, first for washing, and that a Hamburg yard ran six of them.
Credit
Hammelmann (maker); the Dutch contractor named in the report as Doornbus Vehur
Watch for
Magnetic robots blast and coat
RobotPlusPlus showed its HighMate robots, which hold to steel with magnets, at the SMM shipbuilding fair in Hamburg. It says its coating robot sprays 300 to 500 m² an hour on ships, tanks and bridges with overspray "nearly negligible" and a system to recover solvent vapor, and that its ATEX Zone 1 model, certified for areas where explosive gas may be present, carries swappable water jetting, cleaning, coating and abrasive blasting heads, at more than 40 m² an hour with over 99% of waste water recovered.
Achieved whena shipyard, tank owner or classification society publishes rates, film thickness and water recovery measured on production jobs.
Claimed by
RobotPlusPlus (founder and CEO Hua-Yang Xu), reported October 2026
Open
01
Mask structural steel by robot
A robot arm that fits masking (tape, silicone plugs and caps) to fabricated steel parts before blasting and painting, at the spots the fabricator's 3D model marks to stay bare, such as bolt holes, threaded studs and connection surfaces, and a score sheet for others to use.
The briefCredit · unclaimed02
A ledger of robot trials
A public table of every blasting, water jetting and painting robot for steel structures with a published trial, giving the rate, finish, waste and exposure figures, and for each figure who measured it: the maker, the customer or an outside party.
The briefCredit · unclaimed
Open 01 · the brief
Mask structural steel by robot
The first to publish is credited on this line, and the deliverable moves from Open to Achieved.
What to build
A robot arm that fits masking (tape, silicone plugs and caps) to fabricated steel parts before blasting and painting, at the spots the fabricator's 3D model marks to stay bare, such as bolt holes, threaded studs and connection surfaces, and a score sheet for others to use.
Why it is still open
Published robot masking is for aircraft and engine parts with repeated shapes. MTU Aero Engines replaced hand masking of engine parts with a robot-applied liquid mask in 2023, and Aerobotix and FerRobotics launched a robot tool that applies masking tape to aircraft the same year. A Crossref search, an arXiv search and a GitHub search in November 2026 found no robot that masks one-off structural steel parts from their model.
Built with what exists
A collaborative arm such as a Universal Robots UR10e; FerRobotics' Active Taping Kit or a simple tape head; standard silicone plugs and caps; an Intel RealSense depth camera; IfcOpenShell to read the fabricator's IFC model; Hugging Face LeRobot to record demonstrations and an open robot model such as NVIDIA's GR00T 2 or Runway's Praxis-1 to learn plug fitting (see the Notes "No download", "Five demonstrations per task" and "Open robot model weights"). Bare steel offcuts only; no blasting or painting is part of the test.
First step
Ask a local steel fabricator for the IFC models and offcuts of three beam types, and time a person masking them.
Done looks like
20 parts made from a fabricator's real drawings, with at least 300 mask points in all, masked by the robot and by a person; the share of points placed within 2 mm of the model, the share that stay put under a set pull with a spring gauge, and minutes per part, published with video.
Open 02 · the brief
A ledger of robot trials
The first to publish is credited on this line, and the deliverable moves from Open to Achieved.
What to build
A public table of every blasting, water jetting and painting robot for steel structures with a published trial, giving the rate, finish, waste and exposure figures, and for each figure who measured it: the maker, the customer or an outside party.
Why it is still open
The last outside survey this research found is NIOSH's of 2000, which counted nine prototypes, observed some of them, and left most production rates as the makers' own. Later figures come from makers and trials: a 2021 shipbuilding research program workshop reported that a robotic grit blaster's first hull demonstration produced "lessons learned" and a second at another yard went well, without rates, and RobotPlusPlus's 2026 rates carry no outside measurement. A GitHub search for a robot blasting or painting benchmark in November 2026 returned nothing.
Built with what exists
Papers from Crossref and the ISARC proceedings, trade press, makers' pages and patents; a language model to pull figures and their source into a fixed form (see the Note "Seven more flagged"); a spreadsheet on GitHub; a second person to check each figure against its source.
First step
Enter the nine NIOSH devices of 2000 and the robots in this section, and send each maker still trading a request for any outside test reports.
Done looks like
At least 50 systems, each figure linked to its source and labeled maker, customer or independent, with the share measured independently reported, and a 30-row random check matching the sources on at least 95% of figures.