Industries / Industrial equipment and services / Industrial services / Motor rewinding
Bearings and balancing
Bearings carry the turning shaft and are the part of a motor that fails most often, and balancing the rotor and aligning the shaft remove the forces that wear them out.
7
Milestones achieved, from 1908 to 2007.
1
To watch for: announced, not yet confirmed outside.
2
Open deliverables. Nobody has shipped them.
The road
AchievedWatch forOpen
Achieved
1908
Balancing by machine
A rotor whose mass is not spread evenly around its axis shakes its bearings at every turn. Carl Schenck's foundry and scale works in Darmstadt, Germany, made balancing machines from 1907 and in 1908 took a license for a balancing machine patented by the engineer Franz Lawaczeck. Schenck RoTec calls its founder "the inventor of the balancing machine", while the trade magazine Industrial Production says a balancing machine was first mentioned in 1870.
Credit
Carl Schenck; Franz Lawaczeck
1949
Bearing life by statistics
Gustaf Lundberg and Arvid Palmgren published a theory of fatigue failure in rolling bearings that uses a modified form of Weibull's statistical theory of failure to account for how much material is under stress, so that a bearing's life is treated as a matter of probability. They set the unknown exponents in their formulas with extensive tests and compared the final formulas with test results.
Credit
Gustaf Lundberg and Arvid Palmgren
1966
Grades for balance
The German engineers' association VDI issued guideline VDI 2060 in October 1966 on how well rigid rotors must be balanced. The international standard ISO 1940-1:1986 set out balance quality requirements and the permissible leftover unbalance for rigid rotors, and the German standards publisher lists it as the replacement for VDI 2060; ISO's current standard on the subject is ISO 21940-11:2016.
Credit
VDI; ISO
1984
Shafts aligned by laser
A motor's shaft must line up with the shaft of the machine it drives, or the coupling loads the bearings. PRÜFTECHNIK of Ismaning, Germany, said in a May 2014 release marking 30 years of laser shaft alignment that its OPTALIGN was the first laser shaft alignment system on the market and a large step beyond conventional methods, and that it became a standard for the job.
Credit
PRÜFTECHNIK
1985
Bearings fail most often
A working group of the Institute of Electrical and Electronics Engineers (IEEE) surveyed motors over 200 hp in industrial and commercial plants and published the results in 1985; in the maintenance publication ReliaMag's table of the survey, bearings caused 44% of failures, windings 26% and rotors 8%, and an earlier EPRI study of about 4,800 utility motors gave 41% bearings and 36% stator windings. A 2019 EPRI survey of ten US nuclear plants put bearings behind 60% of medium-voltage motor failures, and 90% of answers named regreasing as the most effective maintenance for low-voltage motors.
Credit
IEEE Motor Reliability Working Group; Electric Power Research Institute (EPRI)
1996
Drives that pit bearings
Shaotang Chen, Thomas Lipo and D. Fitzgerald wrote in 1996 that drives using pulse-width modulation (PWM), which switch the supply on and off rapidly to shape the output, had "recently been found to be a major cause" of motor bearing failures: the drive's common-mode voltage couples through the motor's internal capacitances onto the rotor and returns to ground through the bearings. In 1997 D. Busse and colleagues set out the theory of the resulting discharges as electric discharge machining (EDM), the same sparking process used to cut metal, and proposed a calculation of a system's potential for it.
Credit
Shaotang Chen, Thomas A. Lipo and D. Fitzgerald; D. Busse, J. Erdman, R. J. Kerkman, D. Schlegel and G. Skibinski
2007
A brush of fibers
A shaft grounding ring gives drive-induced current a path from shaft to frame that bypasses the bearings. In 2007 Annette Muetze of the University of Warwick and H. William Oh of Electro Static Technology set out design rules for brushes made of millions of conductive microfibers, which, unlike carbon brushes, have negligible wear and can carry currents at megahertz frequencies, and supported them with measurements at several shaft speeds. Electro Static Technology, now an ITW company, says its AEGIS ring is used in millions of motors.
Credit
Annette Muetze; H. William Oh and Electro Static Technology
Watch for
Ceramic balls against current
SKF India (Industrial) launched CeraDrive, a hybrid bearing that combines steel with silicon nitride, a ceramic, and claims up to 99% protection against electrical erosion, up to 50% lower friction, up to eight times longer grease life and four to ten times longer bearing life than conventional bearings.
Achieved whena customer or laboratory outside SKF publishes bearing life or erosion results for CeraDrive bearings in drive-fed motors, side by side with conventional bearings.
Claimed by
SKF India (Industrial), May 2026
Open
01
Bearing currents at 48 volts
A bench rig in which small 48 V three-phase motors are driven by gallium nitride (GaN) and silicon drive boards at several switching speeds, measuring the voltage between shaft and frame and counting discharges through the bearings, followed by runs of hundreds of hours and a microscope check of the bearing races for the dull frosting that discharges leave.
The briefCredit · unclaimed02
Public test for bearing photos
An open set of photos of bearings removed from motors in repair shops, labeled by the damage modes of the ISO 15243 standard by two people working separately, with a scorecard on which any photo tool can be tested, including how often it gives no answer.
The briefCredit · unclaimed
Open 01 · the brief
Bearing currents at 48 volts
The first to publish is credited on this line, and the deliverable moves from Open to Achieved.
What to build
A bench rig in which small 48 V three-phase motors are driven by gallium nitride (GaN) and silicon drive boards at several switching speeds, measuring the voltage between shaft and frame and counting discharges through the bearings, followed by runs of hundreds of hours and a microscope check of the bearing races for the dull frosting that discharges leave.
Why it is still open
Bearing damage from drives was traced at mains voltages in the 1990s, and recent work is at that scale too: Ghent University researchers (Machines, August 2026) measured shaft voltage and bearing current on an 11 kW motor with three cable lengths, and Mustafa Memon and Mohamed Diab (Energies, November 2025) measured EDM bearing currents in drives built with fast-switching wide-bandgap chips, naming robotics among the uses, and designed a choke to stop them. Neither abstract describes a 48 V drive or reports bearing wear after a long run, and Crossref and web searches in November 2026 found no study that does, while GaN drivers are now being made for 48 V robot joints.
Built with what exists
A GaN half-bridge motor-driver board, such as STMicroelectronics' GANSPIN parts (see the Note "A half-bridge in 6.5 by 5 mm"), and a silicon MOSFET board for comparison; off-the-shelf 48 V motors with standard deep-groove ball bearings; an oscilloscope with a high-bandwidth probe and a shaft brush as the contact; a USB microscope camera for the races.
First step
Put a scope probe between the shaft and frame of one 48 V motor on an existing drive board and record whether any common-mode voltage appears on the shaft.
Done looks like
Shaft voltage and discharge counts at four or more switching speeds, for GaN and silicon, on at least three motors; bearings from 500-hour runs photographed under the same microscope as new ones; the result stated plainly as whether discharges, and visible damage, occur at 48 V; data, wiring diagrams and code published.
Open 02 · the brief
Public test for bearing photos
The first to publish is credited on this line, and the deliverable moves from Open to Achieved.
What to build
An open set of photos of bearings removed from motors in repair shops, labeled by the damage modes of the ISO 15243 standard by two people working separately, with a scorecard on which any photo tool can be tested, including how often it gives no answer.
Why it is still open
SKF engineers trained an object-detection model on 11,000 images of seven ISO 15243 damage modes, including current leakage erosion, labeled by SKF staff, and reported in June 2024 that its threshold left about 32% of test images with no prediction; the images were not published. NSK's free Bearing Doctor app shows reference images of damage types, including electrical corrosion, for a person to compare by eye. A GitHub search for bearing failure images found no repositories, and the one bearing-damage classifier found works on vibration signals, not photos.
Built with what exists
Phone cameras with a ring light; Label Studio for boxes and labels; open object-detection models such as RetinaNet in torchvision or Ultralytics YOLO as baselines.
First step
Ask a motor repair shop to keep every bearing it removes for a month in labeled bags with the motor's details, then photograph the rings and balls under one light.
Done looks like
At least 2,000 photos of at least 600 bearings from at least four motor repair shops, each labeled by two people with their agreement reported; precision and recall for each damage mode, and the share of photos left without an answer, for at least one open model on photos from a shop held out of training; data published under an open license.