BRENNEN

Industries / Transport and vehicles / Maritime and shipping

Ships and propulsion

Naval architects, shipyards and engine makers design and build cargo ships: the hull, the engines that push it through the water, and the fittings that hold cargo in place.

6

Milestones achieved, from 1843 to 2025.

2

To watch for: announced, not yet confirmed outside.

2

Open deliverables. Nobody has shipped them.

The road

AchievedWatch forOpen

Achieved

  1. 1843

    Iron hull and propeller

    Isambard Kingdom Brunel's SS Great Britain was launched at Bristol in 1843. She was built of iron plates and driven by a propeller (a bladed screw that turns under water), with an engine of about 1,000 horsepower. The SS Great Britain Trust, which shows the ship in the dry dock where she was built, says she was the largest ship in the world at launch and "the blueprint for every ocean liner that followed." The Trust words the "first" two ways: "one of the first iron, propeller-driven ocean liners" on its home page, and "the first ocean-going ship in history to be built from metal, and the first to be moved by a propeller" on its dockyard history page.

    bristoldockyards.orgbristoldockyards.org

    Credit

    Isambard Kingdom Brunel (design) and William Patterson (builder)

  2. 1912

    Diesel crosses the ocean

    Selandia, built by Burmeister & Wain in Copenhagen for the East Asiatic Company, entered liner service between Bangkok and the UK in 1912 with two 1,000 horsepower diesel engines. She was 113 m long and could carry 7,000 deadweight tons (dwt: the weight of cargo, fuel and stores a ship can lift). The contract let the owner swap the diesels for steam engines if they performed poorly, with yard and owner each paying half. Engine maker Everllence (formerly MAN Energy Solutions) lists her as the "first sea-going ship" with diesel propulsion; The Motorship says the Djelo and the Vulcanus "are often quoted," but that for ships able to cross the Atlantic "there is no doubt that the answer is Selandia." It reports that by the early 1950s diesel had replaced steam as the main power plant for ships.

    motorship.comeverllence.com

    Credit

    Burmeister & Wain and the East Asiatic Company

  3. 1943

    Welded hulls crack in two

    US yards built 2,580 Liberty ships, 414 Victory ships and 530 T2 tankers with welded steel hulls between 1941 and 1946. On 16 January 1943 the T2 tanker Schenectady, 152 m long and a few days past sea trials, broke in two at the Kaiser Company's outfitting dock in Portland, Oregon. A Board of Investigation set up at the US Coast Guard's request reviewed 4,694 welded merchant ships and reported in 1946 that 970 had cracked. It found the cracks began at notches in steel that turned brittle (cracking suddenly, without bending first) at the temperatures the ships worked in; the same steel had been acceptable in riveted ships.

    Lessona welded hull needs steel specified for toughness at its working temperature, checked with tests such as the Charpy test (the energy needed to snap a notched bar), plus careful joint design and welding.

    twi-global.com

    Credit

    US Coast Guard Board of Investigation; case history published by TWI

  4. 1962

    Nuclear power at sea, briefly

    NS Savannah, a merchant ship driven by a nuclear reactor, was launched in 1959 under President Eisenhower's Atoms for Peace program. The US Maritime Administration (MARAD) ran her from 1962 until 1970, when she was taken out of service, and her fuel was removed in October 1971. gCaptain calls her the world's first nuclear-powered merchant ship. Her reactor vessel was lifted out on 8 November 2022 and sent by rail to a disposal site in Clive, Utah; the US Nuclear Regulatory Commission approved MARAD's license termination plan on 30 January 2025 and expects the work to close by 2031.

    nrc.govgcaptain.com

    Credit

    US Maritime Administration

  5. 2022

    Boxships reach 24,000 TEU

    In August 2022 the classification society ABS (a private body that checks a ship against its construction rules) announced that Ever Alot, a 400 m ship built by Hudong-Zhonghua Shipbuilding in China, had been delivered to its class as "the largest container ship in the world," at just over 24,000 TEU (twenty-foot equivalent units, a count of standard 20-foot boxes). FreightWaves lists her at 24,004 TEU for Evergreen Marine, ahead of the 2021 record holder Ever Ace at 23,992 TEU, and reports that the average container ship grew from under 3,000 TEU in 2012 to about 4,500 TEU.

    hellenicshippingnews.comfreightwaves.com

    Credit

    Evergreen Marine and Hudong-Zhonghua Shipbuilding

  6. 2025

    Recycling treaty takes force

    Old ships are sold for scrap and cut up for steel, often on tidal beaches. The 2009 Hong Kong Convention for the Safe and Environmentally Sound Recycling of Ships came into force in June 2025, UNCTAD reports. The NGO Shipbreaking Platform counted 321 ships dismantled worldwide in 2025, 214 of them on the beaches of Bangladesh, India and Pakistan, which took 85 percent of the tonnage scrapped; it recorded 11 workers killed and at least 62 injured there.

    Lessonthe Platform reports serious accidents at Bangladeshi yards approved under the convention, so a treaty in force did not by itself make the work safe.

    unctad.orgshipbreakingplatform.org

    Credit

    International Maritime Organization (IMO) member states

Watch for

  1. Ammonia engine goes to sea

    Exmar took delivery of Antwerpen on 10 June 2026, a carrier for 46,000 m³ of liquefied petroleum gas or ammonia built by HD Hyundai Heavy Industries. Her WinGD X52DF-A two-stroke engine (the large, slow-running type that turns a ship's propeller directly) can burn ammonia, which contains no carbon, lit by about 5 percent pilot fuel (a small dose of conventional fuel) at full load. WinGD calls her "the world's first ocean-going ship designed to operate on ammonia fuel" and says sea trials in May 2026 matched its diesel engines; Riviera reports that she burns ammonia only at sea and switches to conventional fuel below 25 percent engine load. No measured emissions have been published.

    Achieved whenthe ship has run on ammonia in commercial service and a party outside WinGD and Exmar publishes its measured fuel use and its emissions of nitrous oxide and unburned ammonia.

    wingd.comrivieramm.com

    Claimed by

    WinGD and Exmar, June 2026

  2. Sails on a cargo route

    Neoliner Origin is a 136 m roll-on/roll-off ship (cargo is driven or rolled aboard) with two rigid SolidSail rigs, built by RMK Marine in Turkey for the French owner Neoline. She entered service in October 2025 between Montoir-de-Bretagne in France and Baltimore, Halifax and Saint-Pierre-et-Miquelon. Neoline says she cut fuel use by 70 percent in 2026 against a fleet reference from the Global Logistics Emissions Council, short of its 80 percent target because of sail problems, and by 62 to 67 percent against a simulated ship of the same size without sails. The Maritime Executive names no outside party that checked the figures.

    Achieved whena party outside Neoline measures the ship's fuel use over a full year against a stated baseline and publishes the result.

    maritime-executive.com

    Claimed by

    Neoline, November 2026

Open

  1. 01

    A register of lost containers

    a public table with one row for every incident in which a ship lost containers overboard from 2010 to 2025: date, ship, IMO number, size in TEU, position, number of boxes lost, weather where reported, the cause given by investigators, and a link to each source. Ship designers, insurers and the crews who stow cargo could then see which ship sizes, routes and sea conditions lose boxes.

    The brief
    Credit · unclaimed
  2. 02

    Corner casting wear from photos

    a phone method that measures wear on a container's corner castings (the steel blocks at each corner that twistlocks lock into) from a photo taken beside a printed scale target, and flags castings whose openings have worn past a stated limit.

    The brief
    Credit · unclaimed

Open 01 · the brief

A register of lost containers

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

a public table with one row for every incident in which a ship lost containers overboard from 2010 to 2025: date, ship, IMO number, size in TEU, position, number of boxes lost, weather where reported, the cause given by investigators, and a link to each source. Ship designers, insurers and the crews who stow cargo could then see which ship sizes, routes and sea conditions lose boxes.

Why it is still open

the World Shipping Council publishes only yearly totals from a survey of its members: 1,478 containers lost in 2025, 640 of them in one unnamed incident, with causes "based on analysis of media reports." IMO made reporting the loss of containers mandatory from 1 January 2026, but no public list of those reports was found. Searches found yearly totals and agency analyses that name single incidents, but no incident-by-incident public table.

worldshipping.orgimo.org

Built with what exists

investigation reports from national boards such as the Dutch Safety Board, Japan Transport Safety Board, UK Marine Accident Investigation Branch and Germany's BSU; the World Shipping Council's yearly totals as a cross-check; Copernicus Marine wave data to add wave height at each position; PyMuPDF to pull report text; a low-cost extraction model such as Meta's Muse Ember to fill the fields and quote the supporting sentence (Note: "The jobs agents repeat").

  1. First step

    list every incident named in investigation reports and trade-press coverage for 2019 to 2025 and fill 20 rows by hand to settle the field definitions.

  2. Done looks like

    at least 150 incidents from 2010 to 2025, every row with a working source link; the yearly sums compared with the World Shipping Council's totals and the gap published; a second person re-codes a random 20 percent of rows without seeing the first codes, and the agreement is published field by field.

Open 02 · the brief

Corner casting wear from photos

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

a phone method that measures wear on a container's corner castings (the steel blocks at each corner that twistlocks lock into) from a photo taken beside a printed scale target, and flags castings whose openings have worn past a stated limit.

Why it is still open

MARIN's TopTier project, set up after the container losses of winter 2020 to 2021, lists "corner casting wear tracking" among technical issues not yet resolved. Inspection guidance from a container maker tells inspectors to check "wear of holes" but gives no way to measure it, while ISO 1161 hole tolerances are typically 0 to +1.5 mm. Searches found no camera-based method.

marin.nlhz-containers.com

Built with what exists

a phone camera; a printed ChArUco calibration board and the OpenCV library (Python) to turn pixels into millimeters and find the edges of each opening; digital calipers for ground truth; worn castings cut out during repairs at a container depot.

  1. First step

    ask a container repair depot for 20 castings it has cut out, measure their openings with calipers, and photograph each beside a printed board.

  2. Done looks like

    200 castings measured both by calipers and by photo; mean error on opening length and width of 0.3 mm or less; every casting the calipers put past the chosen limit flagged by the tool; measurements and code published.