Industries / Construction and property / Janitorial and facility services
Floor care
Floor care is the daily and periodic work of keeping floors clean and safe to walk on: sweeping, vacuuming, mopping and machine scrubbing, stripping and refinishing hard floors, and deep-cleaning carpet.
5
Milestones achieved, from 1901 to 2019.
2
To watch for: announced, not yet confirmed outside.
2
Open deliverables. Nobody has shipped them.
The road
AchievedWatch forOpen
Achieved
1901
Vacuum cleaning as a service
Hubert Cecil Booth, an English engineer, filed on 30 August 1901 for British patent 17,433, which covered cleaning carpets through pipes by suction. His first machine ran on petrol and was not portable: it was parked outside the building and its suction pipes were run inside, and his British Vacuum Cleaner Company sold the cleaning, not the machine. The Science Museum Group says the company was set up in 1901, cleaned the carpet at Westminster Abbey before the coronation of 1902, and removed 23 tons of dust from the Crystal Palace during an outbreak of spotted fever among soldiers stationed there.
Credit
Hubert Cecil Booth; British Vacuum Cleaner Company
1960s
Scrub and dry together
An automatic scrubber, or autoscrubber, puts down cleaning solution, scrubs with a brush or pad, and sucks the dirty water back up through a squeegee in one pass, so the floor is left dry. Jim Van Dusen of the floor machine maker Pioneer Eclipse told the trade magazine Sanitary Maintenance that the machine began as a single-disc floor machine combined with a wet vacuum, and spread in the 1960s once it ran on batteries. Tennant Company says it developed the first riding scrubber "built from the ground up" in 1970, and released its first walk-behind scrubber, the 432, with a 32-inch (81 cm) cleaning path, in 1978.
Credit
floor machine makers, among them Tennant Company; the sources name no single inventor
2002
Microfiber replaces the mop bucket
Microfiber is a dense fabric of polyester and nylon fibers about one sixteenth the thickness of a human hair, by the US Environmental Protection Agency's (EPA) description. A flat microfiber mop head is used for one room and then laundered, so the cleaning solution is never dirtied. UC Davis Medical Center in Sacramento began a pilot in summer 1999 and within a year had replaced loop mops in all patient care areas. A case study by EPA Region 9's pollution prevention program, published in November 2002, reports that the switch cut water use for mopping by 95%, because janitors no longer changed a bucket of solution every two or three rooms, and that the hospital's bacteria cultures showed a 99% reduction after microfiber mopping against 30% after a wet loop mop.
LessonMicrofiber did not suit everything: the hospital kept loop mops for areas with heavy blood or body fluids and machines for greasy kitchens, and the heads had to be laundered away from industrial washers, whose heat damaged them.
Credit
UC Davis Medical Center; US EPA Region 9
2017
Slip tests turn dynamic
A slip test measures how much grip a floor gives a shoe. ASTM C1028, which measured static friction, the force needed to start a Neolite rubber heel sliding, was withdrawn in February 2014 "due to its limited use by industry." Its place went to the Tile Council of North America's DCOF AcuTest, which measures dynamic friction, the force needed to keep a test foot sliding. It entered the American national standard for ceramic tile in 2012 and became a standard for all hard floors, ANSI A326.3, in 2017. The 2021 edition says a level indoor floor expected to be walked on when wet should have a wet dynamic coefficient of friction (DCOF) of 0.42 or more on the BOT 3000E test device, and that a floor's DCOF changes over time with wear and contaminants, so deep cleaning and traction-restoring maintenance may be needed to keep it.
LessonThe standard itself says a DCOF reading compares surfaces but "does not predict the likelihood a person will or will not slip.".
Credit
Tile Council of North America; ASTM Committee C21 withdrew the old test
2019
Robots scrub store floors
On 9 April 2019 Walmart said it would add 1,500 autonomous floor cleaners, which it calls Auto-C, to its US stores. It had brought in 78 floor-scrubbing robots in December 2018, against an original plan of 360, by Retail Dive's account. Walmart wrote that "after an associate preps the area," the machine "can be programmed to travel throughout the open parts of the store." By 2025 the International Federation of Robotics (IFR) ranked professional cleaning, mostly floor cleaning, third among uses of service robots in business, with sales up 40% on 2024, from a sample of 238 robot makers.
LessonEven at Walmart's scale the robot cleans the open floor, and an associate still preps the area first, by Walmart's own description.
Credit
Walmart
Watch for
Robots that refill themselves
Tennant says its X2 ROVR SCRUB, its smallest robotic scrubber, steered by Brain Corp's BrainOS software, cleans aisles as narrow as 29 inches (74 cm), and that its X2 Dock RFSH lets the robot recharge, empty its dirty water, refill clean water and dilute cleaning solution to preset strengths without a person. Orders were to open in late May 2026.
Achieved whena customer publishes several weeks of runs giving how often a person had to empty, refill or rescue the robot.
Claimed by
Tennant Company, May 2026
Fifty thousand robots claimed
Brain Corp says more than 50,000 robots run its BrainOS software worldwide, and that in the first half of 2026 they logged more than 5.3 million hours of autonomous work and covered more than 3.7 billion square feet (about 344 square km), across cleaning, shelf scanning and other jobs. The figures are the company's own.
Achieved whenan outside party, such as an auditor or a group of named customers, publishes robot counts and hours that support the company's totals.
Claimed by
Brain Corp, August 2026
Open
01
A test course for robots
An open test course and scoring method for commercial floor-cleaning robots: a marked floor with open aisles, a strip along walls, inside corners, chair legs and a dropped cable, spread with a measured test soil before each run. The score covers the share of floor cleaned, the soil removed, the width of the strip left along walls, the water left behind and the number of times a person had to step in.
The briefCredit · unclaimed02
Mapping floor grip by robot
A sled, towed by a small mobile robot or hitched behind an autonomous scrubber, that measures the floor's dynamic friction continuously as it moves, using a load cell and the rubber test foot that ANSI A326.3 specifies, so a building gets a map of floor grip that can be repeated every week. It would show where finish build-up, cleaning residue or wear has made a floor slippery.
The briefCredit · unclaimed
Open 01 · the brief
A test course for robots
The first to publish is credited on this line, and the deliverable moves from Open to Achieved.
What to build
An open test course and scoring method for commercial floor-cleaning robots: a marked floor with open aisles, a strip along walls, inside corners, chair legs and a dropped cable, spread with a measured test soil before each run. The score covers the share of floor cleaned, the soil removed, the width of the strip left along walls, the water left behind and the number of times a person had to step in.
Why it is still open
The international standard for commercial scrubbers and sweepers, IEC 62885-9:2019, lists performance figures "to serve the manufacturers in describing parameters for their manuals" and does not mention robots; the robot standard in the same series, IEC/ASTM 62885-7, is for household dry-cleaning robots. Japan's trade ministry said in March 2019 that it would set a Japanese Industrial Standard for office cleaning robots that remove dust, with test methods for dust removal and movement, by the 2020 fiscal year; a search did not find it published, and it would not cover scrubbers. A search for independent tests of commercial floor robots found only buyer guides written by robot makers. The IFR counts robots sold, not how well they clean, and Brain Corp's fleet figures are its own.
Built with what exists
Floor tape and a gym or warehouse floor; a test soil mixed to a published recipe; a camera on a pole or ceiling mount and the open-source OpenCV library to compare before and after photos; a moisture meter for water left behind; robots borrowed or rented from makers such as Tennant, Avidbots, Gausium, LionsBot and Kärcher; a walk-behind scrubber run by a person as the baseline.
First step
Lay out a 10 m by 10 m course with tape, run one borrowed robot and one walk-behind scrubber five times each, and publish the draft method for comment.
Done looks like
At least three commercial robot models and one person with a walk-behind scrubber, each run 20 times on the same course, with a published table of floor share cleaned, soil removed, width of the missed strip along walls in centimeters, water left and interventions per run, plus the method and photos under an open license.
Open 02 · the brief
Mapping floor grip by robot
The first to publish is credited on this line, and the deliverable moves from Open to Achieved.
What to build
A sled, towed by a small mobile robot or hitched behind an autonomous scrubber, that measures the floor's dynamic friction continuously as it moves, using a load cell and the rubber test foot that ANSI A326.3 specifies, so a building gets a map of floor grip that can be repeated every week. It would show where finish build-up, cleaning residue or wear has made a floor slippery.
Why it is still open
ANSI A326.3 says installed floors change grip over time with wear and contaminants, and that its 0.42 threshold applies to the BOT 3000E device, with any other device to be "independently correlated" to it, so testing is done spot by spot with that device. Outdoors, Findlay Irvine's micro GripTester, a push-along tester that uses the same braked-wheel method as its trailer-towed GripTester, measures skid resistance on footways and pedestrian zones, but it does not use the A326.3 test foot and is not sold for indoor floors. Searches of Crossref (for slip-resistance mapping and continuous floor surveys) and GitHub (for tribometers, devices that measure friction) found lab and hobby friction testers but no device that maps floor friction across a building.
Built with what exists
A load cell with an HX711 amplifier board; an SBR (styrene-butadiene rubber) test foot made to the A326.3 specification; a mobile robot base such as TurtleBot 4 running the open ROS 2 software to map and log position (the Note "A camera on patrol" covers a consumer robot that maps an indoor space and drives itself to saved spots); a BOT 3000E for correlation; floor tiles whose makers declare their DCOF under A326.3.
First step
Build the sled and drag it at a steady speed over five tiles with published DCOF values, then compare the readings with the makers' figures.
Done looks like
Wet and dry readings within 0.05 of the BOT 3000E at 90% or more of 100 marked spots on at least three floor types, and a published four-week map of one building's floors with each change in grip matched to the cleaning or refinishing done there.