Industries / Industrial equipment and services / HVAC equipment
Compressors
The compressor is the pump at the heart of an air conditioner, heat pump or refrigerator: it squeezes refrigerant vapor so that it can give up heat outdoors, and makers build it in several shapes, from pistons to spinning impellers.
6
Milestones achieved, from 1834 to 2001.
1
To watch for: announced, not yet confirmed outside.
2
Open deliverables. Nobody has shipped them.
The road
AchievedWatch forOpen
Achieved
1834
Ice from a closed loop
Jacob Perkins, an American inventor working in England, patented "Apparatus and means for producing ice, and in cooling fluids" in 1834. In his machine a pump compressed a vapor, the vapor turned to liquid and gave off heat, and the liquid then boiled again at low pressure and drew heat out of water, over and over in a sealed circuit. This vapor-compression cycle is still how nearly every air conditioner and refrigerator works. The American Society of Mechanical Engineers (ASME) calls Perkins's device "the first working device to use a system of vapor-compression for refrigeration", built and demonstrated in 1835 by his associate John Hague, and named it a landmark in 2020.
LessonPerkins did not sell machines; by ASME's account it took Hague and others to make models fit for sale.
Credit
Jacob Perkins; John Hague; Oliver Evans, who described the cycle in 1805 but never built it
1922
Centrifugal chillers cool crowds
In May 1922 Willis Carrier unveiled a centrifugal refrigeration machine, or chiller, in which a fast-spinning impeller compresses the refrigerant instead of a piston. Carrier's history says the machines gave "affordable, safe and efficient cooling", and his company used them to cool department stores, theaters and office towers; in 1924 the J.L. Hudson store in Detroit installed three 195-ton chillers (a ton of cooling removes about 3.5 kW of heat). By 1937 several 140-ton centrifugal machines had been lowered down shafts to cool the Magma copper mine in Superior, Arizona, which ASME calls the first air-conditioned mine in North America.
Credit
Willis Carrier and Carrier Engineering Corporation
1927
A sealed fridge for homes
General Electric introduced the Monitor Top refrigerator, named for its round compressor housing that looked like the gun turret of the Civil War ship USS Monitor. Its works sat in a hermetically sealed steel case: in a hermetic compressor the electric motor is sealed inside the same shell as the pump, so there is no turning shaft passing through a seal for refrigerant to leak past. The Albany Institute of History & Art, quoted by ACHR News, says it sold for about $525 at launch and that models sold for as little as $200 within a few years. Schenectady's Museum of Innovation and Science calls it the first hermetically sealed steel refrigerator.
Credit
Christian Steenstrup, whom the Albany Institute calls GE's chief engineer; ASME's listing of the Refrigeration Research Museum says the design is said to refine the earlier Audiffren machine from France
1980
Compressors change speed
Toshiba says it released the world's first inverter-based home air conditioner in 1980. An inverter is an electronic drive that changes the frequency of the power fed to the compressor motor, so the compressor can run slowly when little cooling is needed instead of switching fully on and off. Toshiba had made Japan's first rotary compressor for air conditioners in 1967, by its own history. The International Energy Agency's 2018 cooling report lists the inverter compressor as one of the standard choices in an air conditioner, and some efficiency labels state whether a unit has one.
Credit
Toshiba (now Toshiba Carrier)
1983
Scrolls made at last
A scroll compressor squeezes gas between two interleaved spirals, one fixed and one orbiting. Léon Creux of Paris patented the idea in the US in 1905, as a steam engine that could also serve as a compressor. An article by K. Fujie in the Japanese journal Refrigeration (2000), abstracted by the International Institute of Refrigeration (IIR), says no one could build it for decades because the orbiting spiral was hard to support and the spirals hard to machine accurately; Hitachi began work in 1975 and put the first air conditioners with hermetic scroll compressors on sale in March 1983. Copeland opened North America's first scroll plant, in Sidney, Ohio, in 1987. ACHR News reported in 2007 that in 1987 the whole US industry used piston (reciprocating) compressors in its 8 SEER systems, and that scrolls were by then in more than two-thirds of systems meeting the 13 SEER efficiency standard.
LessonThe 1905 idea waited almost 80 years for machining precise enough to make it.
Credit
Léon Creux; Hitachi; Copeland (Emerson)
2001
Compressors without oil
Most compressors need oil to lubricate their bearings, and some of that oil travels with the refrigerant and coats the heat exchangers. Turbocor's TT300, launched in 2001, is a small centrifugal compressor whose shaft floats on magnetic bearings, so it needs no oil, and it runs at variable speed. Danfoss says the first one was built in Melbourne, Australia, in 1995 and calls Turbocor the first oil-free magnetic-bearing compressor. In 2009 the UK's Institute of Refrigeration gave the founder, Ron Conry, its Gold Medal, and ACHR News reported more than 10,000 of the compressors in use worldwide.
Credit
Ron Conry and Turbocor; Danfoss, its partner from 2004 and later owner
Watch for
Turbocharger maker enters chillers
Garrett Motion, which makes car turbochargers, says its oil-free centrifugal compressors spin at more than 90,000 rpm on air foil bearings (thin films of gas instead of oil), are more than 50% smaller and 80% lighter than conventional compressors, and saved more than 10% of energy "in real-life use" in trials with HVAC system builders. It plans a range from 7 to 500 tons (25 to 1,750 kW of cooling), which it calls the industry's first, and in October 2026 said Multistack would use it in data center cooling units from the second half of 2027.
Achieved whenequipment using the compressor is in production and an outside party, such as a certified rating test or a measured field study, confirms the energy savings.
Claimed by
Garrett Motion, February 2026 and October 2026
Open
01
Open drive for fridge compressors
Open-source motor-control firmware and a small circuit board that run a 12 or 24 V DC refrigerator compressor, such as Secop's BD35F, without the maker's electronic unit, plus a published comparison of energy use against the stock unit in the same fridge. These compressors cool portable and solar-powered fridges, where every watt counts. The work stays at low voltage and leaves the factory-sealed refrigerant circuit closed.
The briefCredit · unclaimed02
A public compressor map library
A free, machine-readable table of compressor maps for hundreds of compressors. A map, in the form set by the AHRI 540 standard, is ten numbers per quantity that give a compressor's capacity, power and refrigerant flow at any pair of evaporating and condensing temperatures; designers need them to size heat pumps. Pull the published data from makers' datasheets, fit the maps, check each map against the maker's listed points, and publish a first comparison of efficiency by compressor type and refrigerant.
The briefCredit · unclaimed
Open 01 · the brief
Open drive for fridge compressors
The first to publish is credited on this line, and the deliverable moves from Open to Achieved.
What to build
Open-source motor-control firmware and a small circuit board that run a 12 or 24 V DC refrigerator compressor, such as Secop's BD35F, without the maker's electronic unit, plus a published comparison of energy use against the stock unit in the same fridge. These compressors cool portable and solar-powered fridges, where every watt counts. The work stays at low voltage and leaves the factory-sealed refrigerant circuit closed.
Why it is still open
Secop's datasheet lists the BD35F for use "only with BD controller". Public projects on GitHub, such as AK-Homberger/BD35F-FridgeController and microfarad-de/fridge-controller, switch the compressor on and off or set its speed through Secop's own electronic unit, using its thermostat input or a pulse-width signal; none replaces the unit's motor drive. Open firmware for brushless motors exists, such as VESC and Sapog, but a search in November 2026 found none documented for a DC refrigerator compressor and no measured comparison with a stock controller.
Built with what exists
VESC's open-source motor firmware or an STM32 motor-control kit; small gallium nitride (GaN) half-bridges such as ST's GANSPIN1102 (see the Note "A half-bridge in 6.5 by 5 mm"); a portable compressor fridge bought new; a 12 V bench supply, a DC power meter and temperature loggers; an AI coding agent to port and test the firmware.
First step
Log the stock unit's voltage, current and compressor run time on one fridge for a week, as the baseline to beat.
Done looks like
The open drive starts the compressor 100 times out of 100, holds every speed in the datasheet's 2,000 to 3,500 rpm range, and keeps the fridge at the same setpoint for 48 hours in a room held at a fixed temperature using no more energy than the stock unit, within 5%; code and schematics public under an open license, and one outside builder repeats the result.
Open 02 · the brief
A public compressor map library
The first to publish is credited on this line, and the deliverable moves from Open to Achieved.
What to build
A free, machine-readable table of compressor maps for hundreds of compressors. A map, in the form set by the AHRI 540 standard, is ten numbers per quantity that give a compressor's capacity, power and refrigerant flow at any pair of evaporating and condensing temperatures; designers need them to size heat pumps. Pull the published data from makers' datasheets, fit the maps, check each map against the maker's listed points, and publish a first comparison of efficiency by compressor type and refrigerant.
Why it is still open
Maps sit in each maker's datasheets and selection software. The open-source ACHP model implements the AHRI 540 map but ships no library of real compressors; its documentation shows only one example set. An Oklahoma State University project (AR-40, 2022) set out to deliver "a populated compressor performance database"; it was not found published as open data in November 2026. A study by the Universitat Politècnica de València and Oak Ridge National Laboratory, published in Applied Thermal Engineering in 2023, fitted the AHRI equations to seven scroll compressors from AHRI test reports and found that they overfit: unless the measured points are chosen with care, the map strays between and beyond them, and simpler equations did better.
Built with what exists
Makers' public datasheets; a browser agent such as Browser Use to collect them slowly and within each site's terms (see the Note "Deleting 80% to start over"); a low-cost AI model that reads tables from PDFs (see the Note "The jobs agents repeat"); ACHP's compressor code and Python with NumPy for fitting.
First step
Download the datasheets of 20 compressors of one refrigerant from one maker, fit their maps and record how close each comes to the listed points.
Done looks like
Maps for at least 500 compressors from at least five makers and three refrigerants; for 95% of them a map fitted with some datasheet points held back predicts those held-back points within 2%; the table, the fitting code and a chart of efficiency at one standard rating condition by type and refrigerant published under an open license.