BRENNEN

Industries / Construction and property / Commercial and residential construction / Flooring

Concrete coatings

Concrete coating is the work of turning a bare concrete slab into the finished floor itself, either by grinding and polishing the concrete or by bonding a thin layer of resin to it.

5

Milestones achieved, from 1978 to 2024.

1

To watch for: announced, not yet confirmed outside.

2

Open deliverables. Nobody has shipped them.

The road

AchievedWatch forOpen

Achieved

  1. 1978

    Osmosis behind blisters

    W. J. Warlow and P. W. Pye published "Osmosis as a cause of blistering of in situ resin flooring on wet concrete" in Magazine of Concrete Research (September 1978). Osmosis is water moving through a membrane toward a stronger solution: under a resin floor, water can keep flowing toward soluble material trapped beneath the coating until the coating lifts. A 2014 patent cites reports of osmotic pressure as high as 3,000 psi, "much greater than the bond of epoxies and other coatings to a concrete substrate", and notes that slabs above the water table can still blister this way.

    Lessona coating can be pushed off from below by water moving through the concrete, even where no water stands on the slab.

    structurae.netpatents.google.com

    Credit

    W. J. Warlow and P. W. Pye

  2. 1993

    Grinding becomes the finish

    A 2007 history in Concrete Decor says VIC International brought HTC grinders from Sweden to the US in 1993 for surface preparation, SASE followed with the Diamatic in 1997, and by 1999 or 2000 machine and chemical makers were building polished concrete into a trade of its own. It combined diamond grinding with a densifier, a liquid hardener soaked into the concrete; densifiers began as sodium-based products, and by 2007 sodium, potassium and lithium versions were sold. HTC calls its Superfloor method "the original polished concrete floor concept".

    concretedecor.netpdf.directindustry.com

    Credit

    HTC (Sweden), VIC International, SASE, and early densifier makers such as RetroPlate

  3. 1997

    Roughness gets a scale

    ICRI Guideline No. 310.2-1997 gave floor coaters a shared scale of concrete surface profile (CSP), the roughness left by surface preparation: a set of numbered replica chips, from CSP 1, the smooth surface acid etching leaves, to the rough surface a jackhammer leaves. Inspectors compare the prepared floor with the chips by sight and touch and report the closest number; the current edition, 310.2R, comes with ten chips.

    Lessoncoating makers specify how rough the concrete must be, so the trade needed a shared way to name that roughness.

    kta.comdefelsko.com

    Credit

    International Concrete Repair Institute (ICRI)

  4. 2019

    Profile measured in mils

    ASTM D8271, first issued in 2019, lets an inspector measure concrete surface profile with a digital depth micrometer: a flat base rests on the peaks while a spring-loaded tip drops into the valleys, giving a depth in mils (thousandths of an inch) instead of a chip number. A 2022 study by Beamish and Corbett built a table that converts CSP chips 1 to 7 into measured depth ranges, so the two methods can be used together. DeFelsko, which makes one such gauge, says the direct method "is not yet widely specified".

    astm.orgdefelsko.com

    Credit

    ASTM International; Beamish and Corbett

  5. 2024

    Shine graded by instrument

    The Concrete Polishing Council of the American Society of Concrete Contractors grades polished floors in four appearance levels, each defined by distinctness of image (DOI, how sharp a reflection looks, measured to ASTM D5767), gloss and haze; Level 4, "highly polished", needs an average DOI above 70. The chart, dated February 2024, asks for at least three readings for areas up to 1,000 square feet and one more for each extra 1,000, taken within 72 hours of polishing. Husqvarna's Superfloor forms give the reason for such numbers: they make it clear "when the goal has been achieved instead of being left to subjective assessments".

    ascconline.orghusqvarnaconstruction.com

    Credit

    Concrete Polishing Council, American Society of Concrete Contractors

Watch for

  1. Self-driving floor grinder

    Husqvarna says its Autogrinder 8 D grinds and polishes concrete floors on its own. Built on its PG 8 DR planetary grinder, it scans the room, keeps to a planned path once the operator sets the area, pattern and overlap on a touch screen, and stops when a bumper, a hose sensor or a dust-extractor pressure sensor trips. Husqvarna showed it at Bauma in April 2025, said it would go on sale in Europe in late 2025, and lists the launch in its 2025 company history.

    Achieved whenA contractor or test body outside Husqvarna publishes measured results from real jobs, such as square metres ground per hour, finish readings such as DOI, and how often an operator had to step in.

    husqvarnaconstruction.comhusqvarnaconstruction.comhusqvarnagroup.com

    Claimed by

    Husqvarna Construction, April to late 2025

Open

  1. 01

    Whole-floor shine map

    A camera rig on a push cart that photographs the reflection of a known target, such as a printed checkerboard or a bar of LEDs, as it crosses a polished concrete floor, and software that turns the sharpness and brightness of each reflection into DOI and gloss estimates for every square metre, calibrated against a handheld image-clarity meter.

    The brief
    Credit · unclaimed
  2. 02

    A blister test that works

    A test, run before a floor is coated, that predicts whether a resin coating will blister on that slab. Small test patches are coated with the specified resin after recording surface soluble salts (rinse a fixed area with deionized water and read its conductivity), in-slab RH and slab age; a time-lapse camera watches each patch for 90 days and simple image analysis counts the blisters. Then publish which readings predicted blistering.

    The brief
    Credit · unclaimed

Open 01 · the brief

Whole-floor shine map

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

A camera rig on a push cart that photographs the reflection of a known target, such as a printed checkerboard or a bar of LEDs, as it crosses a polished concrete floor, and software that turns the sharpness and brightness of each reflection into DOI and gloss estimates for every square metre, calibrated against a handheld image-clarity meter.

Why it is still open

A polished floor is still accepted on a few spot readings taken by hand. The Concrete Polishing Council asks for at least three readings up to 1,000 square feet and one more per extra 1,000, so a 20,000-square-foot floor gets 22, and Husqvarna's Superfloor report sets the specified values as "the average of 10 measurements". A search found no camera method that maps DOI across a whole floor.

ascconline.orghusqvarnaconstruction.com

Built with what exists

A machine-vision camera or a recent phone, a printed target and a small LED bar on a push cart; Python with OpenCV; a Rhopoint IQ Concrete Clarity Meter (handheld DOI, haze and gloss) for calibration. A self-driving grinder or scrubber could later carry the camera.

  1. First step

    On one polished floor, photograph a reflected checkerboard at 10 spots and read the same spots with a borrowed clarity meter, to see whether image sharpness tracks DOI.

  2. Done looks like

    On at least 5 polished floors, the map's DOI estimate is within 5 points of the meter at 90% of at least 50 check spots per floor, with a count of below-spec patches that the standard spot sampling would have missed.

Open 02 · the brief

A blister test that works

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

A test, run before a floor is coated, that predicts whether a resin coating will blister on that slab. Small test patches are coated with the specified resin after recording surface soluble salts (rinse a fixed area with deionized water and read its conductivity), in-slab RH and slab age; a time-lapse camera watches each patch for 90 days and simple image analysis counts the blisters. Then publish which readings predicted blistering.

Why it is still open

A 2014 patent states, "Currently there is no test available to determine if osmotic blistering will occur in a given situation." Wagner Meters still calls osmotic blisters "the plague of resin floors". The cause is not settled either: in long-term laboratory tests published in 2026, Vogt and Osburg found that a higher moisture content in the substrate reduced blistering of their epoxy system, while condensation in the substrate and alkali-silica reaction could cause it.

patents.google.comwagnermeters.comdoi.org

Built with what exists

A conductivity meter, deionized water and a fixed-area template; F2170 probes; the two-part epoxy the floor will receive, applied as its safety data sheet directs, with gloves and ventilation; a time-lapse camera or an old phone; Python with OpenCV to flag raised spots.

  1. First step

    Coat 6 small patches on an old slab in a garage or shop you control, some over deliberately salted spots and some over clean spots, and start the camera.

  2. Done looks like

    At least 40 test patches on at least 8 slabs, followed for 90 days, with a published table of readings against outcomes; the test passes if it flags at least 8 of every 10 patches that blister and no more than 2 of every 10 that do not.