BRENNEN

Industries / Energy, water and waste / Electric transmission and distribution / EV charging infrastructure

Charger hardware

Charger hardware is the equipment itself: the plug on the cable, the socket on the car, the electronics that turn grid power into what a battery can take, and the standards that let one car use many chargers.

7

Milestones achieved, from 1900 to 2025.

2

To watch for: announced, not yet confirmed outside.

2

Open deliverables. Nobody has shipped them.

The road

AchievedWatch forOpen

Achieved

  1. 1900

    A coin-operated charging hydrant

    At the first automobile show of the Automobile Club of America, held at Madison Square Garden in New York from 3 to 10 November 1900, General Electric showed an "electrant," an electric hydrant for charging the batteries of electric vehicles. The trade journal American Electrician reported in December 1900 that it had four sockets giving 20, 30, 40 and 50 amperes, and that a driver plugged in, dropped a 25-cent coin in the slot and received a 2½ kilowatt-hour charge.

    archive.org

    Credit

    General Electric Company

  2. 2001

    California picks one plug

    In 2001 electric cars in California charged in two ways that did not fit each other. Ford and Honda used conductive charging, with metal-to-metal contact like an ordinary plug; Toyota, GM and Nissan used inductive charging, where a paddle pushed into the car's socket passes power through a magnetic field, according to the California Air Resources Board's staff. On 28 June 2001 the board ruled that from 2006 a battery electric car needs an SAE J1772 conductive inlet and an on-board charger of at least 3.3 kVA to earn full credit under its zero-emission vehicle rule, finding that building duplicate public and workplace stations for different plugs added cost. Its staff put the cost of converting inductive public chargers at $1.4 million to $2 million after 2010.

    LessonTwo plugs in one market made every charging site buy two sets of equipment, and a regulator, not buyers, ended the split.

    ww2.arb.ca.govww2.arb.ca.gov

    Credit

    California Air Resources Board

  3. 2010

    Japan's fast-charging protocol

    Tokyo Electric Power Company, Nissan, Mitsubishi Motors, Toyota and Fuji Heavy Industries formally set up the CHAdeMO Association in March 2010 to develop a protocol for direct-current (DC) fast charging, in which the charger outside the car turns grid power into direct current and feeds the battery through a separate DC plug. The association published version 1.0 of the protocol in January 2012 and says installed CHAdeMO chargers passed 20,000 worldwide in 2018.

    chademo.com

    Credit

    CHAdeMO Association and its five founders

  4. 2012

    One inlet, two currents

    On 15 October 2012 SAE International published a revision of its J1772 standard that adds DC fast charging to the AC charging it already covered. The result, the Combined Charging System (CCS), keeps the five-pin J1772 layout for AC and adds two DC pins below it in one inlet. SAE said it would cut charging time "from as long as eight hours to as short as 20 minutes," and that more than 190 experts from carmakers, charger makers, utilities and national laboratories wrote it. In Europe, Directive 2014/94/EU, adopted on 22 October 2014, made every public charger deployed or renewed from 18 November 2017 carry at least Type 2 sockets for AC (standard EN 62196-2) and, for DC, at least the CCS connector the directive calls "Combo 2" (EN 62196-3).

    prnewswire.comdriveelectric.govlegislation.gov.uklegislation.gov.uk

    Credit

    SAE International, task force chair Gery Kissel of General Motors; the European Parliament and Council

  5. 2023

    China rewrites its rules

    China's State Administration for Market Regulation and its Standardization Administration issued GB/T 18487.1-2023 on 7 September 2023, in force from 1 April 2024, replacing the 2015 version of the general rules for conductive charging. The CHAdeMO Association says this standard and two issued with it are the Chinese national form of ChaoJi, a newer charging design that the China Electricity Council and CHAdeMO agreed in August 2018 to develop together. A 2022 presentation by Zhang Xuan of NARI Group (SGEPRI), who worked on the revision, says it covers DC charging at up to 1,500 V and two-way charging between car and grid.

    chinesestandard.netchademo.comchademo.com

    Credit

    China Electricity Council; CHAdeMO Association; China's national standards bodies

  6. 2024

    Tesla's plug becomes standard

    In November 2022 Tesla renamed its own connector the North American Charging Standard (NACS) and opened the design to other carmakers. SAE International formed a task force in June 2023, published a Technical Information Report in December 2023 and, after a task force vote in August 2024, released Recommended Practice J3400 by 30 September 2024, according to the US Joint Office of Energy and Transportation and the charging association CharIN. Unlike CCS, the J3400 plug uses the same pins for AC and DC. The Joint Office says all major automakers have announced plans to adopt it.

    driveelectric.govcharin.global

    Credit

    Tesla; SAE International J3400 task force

  7. 2025

    Adapters fail heat tests

    While North American cars switch plugs, drivers use adapters between NACS and CCS. In a report dated August 2025, engineers at the National Renewable Energy Laboratory (since renamed the National Laboratory of the Rockies) tested five such adapters for the ChargeX Consortium of US national laboratories. Only two signaled the J3400 "thermal warning" state properly, none fully met the J3400 shutdown requirement, one never signaled a warning or shutdown at all, and none fully met the temperature limits of UL 2252, the safety standard for adapters. All five were made before those standards were released.

    LessonA part added between a certified car and a certified charger sits outside both safety designs, so it has to report its own heat.

    osti.gov

    Credit

    Isaac Tolbert, Saroj Shinde, Marco Gaxiola, Douglas DeVoto, Joshua Major, Andrew Meintz and Kristi Moriarty (NREL), ChargeX Consortium

Watch for

  1. Wireless charging while driving

    Electreon and VINCI Autoroutes say coils buried under 1.5 km of the A10 motorway southwest of Paris charge moving vehicles without a cable. Three laboratories of Gustave Eiffel University, a partner in the project, measured peaks above 300 kW and averages above 200 kW "under optimal steady-state conditions" in what Electreon calls a preliminary analysis. A truck, a van, a car and a bus fitted with receiver coils drive the section in live traffic. No later report with the energy delivered was found.

    Achieved whena final measurement report, by the university or another outside party, gives the energy delivered to vehicles over months of traffic, or a stretch opens to paying users.

    prnewswire.comvinci.com

    Claimed by

    Electreon and VINCI Autoroutes, October 2025

  2. Robots that plug in

    Rocsys launched the M1 in April 2026, a robot on an overhead rail that plugs in and unplugs cars at up to 10 charging bays in a robotaxi depot. The company claims a plug-in success rate above 99.9%, based on more than six years of operating data, and says the M1 is in pilot use now with large-scale rollout planned for 2027. No outside measurement was found.

    Achieved whena named fleet operator or outside tester publishes the plug-in success rate over at least a thousand unattended sessions.

    tech.eu

    Claimed by

    Rocsys, April 2026

Open

  1. 01

    Adapters tested after the standards

    A public bench test of the NACS-to-CCS and CCS-to-NACS adapters on sale in 2026, after the first edition of UL 2252 (March 2025) and SAE J3400/1, checking whether each one reports heat the way J3400 requires. Each adapter is warmed slowly in a lab oven with no charging current flowing, while a low-voltage circuit reads its proximity pin, the signal wire that tells the car an adapter is plugged in and, under J3400, that it is getting too hot. The test records the temperature at which the "thermal warning" and "thermal shutdown" signals appear and compares it with the standard. The same table checks each adapter's claimed certification against the certifier's public directory. This tests the warning signal, not how hot the adapter runs under current.

    The brief
    Credit · unclaimed
  2. 02

    Robot plug-in, tested in public

    A robot arm that learns, from a few dozen human demonstrations, to push a real but unpowered CCS1, CCS2 or J3400 connector into an unpowered inlet fixed to a mock car panel, and a public test protocol that varies inlet height and angle, charge-port flap, light and wet weather.

    The brief
    Credit · unclaimed

Open 01 · the brief

Adapters tested after the standards

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

A public bench test of the NACS-to-CCS and CCS-to-NACS adapters on sale in 2026, after the first edition of UL 2252 (March 2025) and SAE J3400/1, checking whether each one reports heat the way J3400 requires. Each adapter is warmed slowly in a lab oven with no charging current flowing, while a low-voltage circuit reads its proximity pin, the signal wire that tells the car an adapter is plugged in and, under J3400, that it is getting too hot. The test records the temperature at which the "thermal warning" and "thermal shutdown" signals appear and compares it with the standard. The same table checks each adapter's claimed certification against the certifier's public directory. This tests the warning signal, not how hot the adapter runs under current.

Why it is still open

The national laboratories' August 2025 tests covered five adapters, all made before the standards existed. Their April 2026 follow-up tested how eight production cars respond to adapter warning signals, using a lab fixture rather than the adapters now on sale, and their February 2026 report tested adapters for side loads and pulling force, not heat signals. No public test of adapters built to the new standards was found.

osti.govosti.govinl.gov

Built with what exists

A benchtop oven or temperature chamber with a thermocouple logger; a low-voltage proximity circuit built to the values in SAE J3400/1 (the April 2026 laboratory slides list nominal proximity voltages from 4.46 V for "disconnected" to 0.63 V for "DC thermal shutdown"); a USB data logger; certifiers' online directories, such as UL Product iQ.

  1. First step

    Buy three adapters from different makers, build the proximity reader, and run the warning-state check on one of them.

  2. Done looks like

    At least 15 adapter models bought at retail in 2026, each with a published curve of proximity voltage against temperature, the temperature at which each signal appeared against the J3400/1 limit, and the result of the certification check, with raw data public.

Open 02 · the brief

Robot plug-in, tested in public

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

A robot arm that learns, from a few dozen human demonstrations, to push a real but unpowered CCS1, CCS2 or J3400 connector into an unpowered inlet fixed to a mock car panel, and a public test protocol that varies inlet height and angle, charge-port flap, light and wet weather.

Why it is still open

Lab robots have plugged in cars before, each on its own rig with one plug type. Lv and colleagues reported a 92% success rate with a camera and a force sensor, as cited by TeslaCharge, a 2023 Skoltech study that tuned its controller from 23 people's recorded plug-ins of a Type 2 connector and reported success without a rate. Other work includes a parallel-arm robot built to reach a car's socket (Chablat, Mattacchione and Ottaviano, 2022), an image set for finding inlets that its authors call the first EV charging inlet dataset (Bang, Lee and Kang, 2021), and student projects on GitHub that find charge ports in camera images. The one figure for a commercial robot, Rocsys's above 99.9%, is the company's own. No shared test across plug types, with a learned robot policy and its weights published, was found.

arxiv.orgarxiv.orgarxiv.orgtech.eu

Built with what exists

A six-axis arm that can carry several kilograms; a wrist camera and force-torque sensor; robot models that learn a task from a handful of demonstrations (see the Note "Five demonstrations per task") or from open weights (see the Note "Open robot model weights"); Hugging Face's LeRobot tools for recording demonstrations; spare inlets and connectors bought as replacement parts.

  1. First step

    Mount an unpowered spare inlet on a plywood panel and record 30 human-guided plug-ins with the arm.

  2. Done looks like

    500 filmed insertion attempts across 10 inlet positions and three plug types, with success rate, time to plug in and any visible pin damage published, along with code and trained weights.