Industries / Construction and property / Heavy civil / Dredging
Dredging vessels
Dredging vessels dig sediment from under water and move it away: bucket dredgers lift it on a chain of buckets, suction dredgers pump it up as a slurry, and hopper dredgers carry it in their own hull.
6
Milestones achieved, from 1575 to 2021.
2
To watch for: announced, not yet confirmed outside.
2
Open deliverables. Nobody has shipped them.
The road
AchievedWatch forOpen
Achieved
1575
A mud mill on treadmills
Joost Janszoon Bilhamer, a Dutch military engineer and surveyor, invented a mud mill in 1575: two flat-bottomed barges with a chain of buckets between them, turned by a treadmill. Four men worked the first treadmills. As dredging went deeper, horses replaced them, and later steam and diesel engines. The brothers Tymon and Adrianus Kater later built a version that could dredge to 5 m. Sources disagree on the first: Prelini's 1911 textbook names a horse-powered dredge by Cornelius Meyer, in 1685, as the first power dredge.
Credit
Joost Janszoon Bilhamer; Tymon and Adrianus Kater
1803
Steam lifts Thames ballast
Richard Trevithick fitted a small high-pressure steam engine to a bucket dredger that broke rock and dredged at the dock entrance at Blackwall, on the Thames, from 1803. A man who worked on it recalled it raising 180 tons of stone and gravel in a tide of six to eight hours. In 1806 Trevithick was close to a deal with the Trinity Board to lift 500,000 tons of Thames ballast a year at sixpence a ton, where hand dredging had cost about eightpence. Sources disagree on the first steam dredger: Prelini's 1911 textbook dates one to 1796 in England, with an engine designed by James Watt, and Samuel Bentham, Inspector of Naval Works from 1796 to 1806, signed plans for a steam dredger at Portsmouth.
Credit
Richard Trevithick; Samuel Bentham
1824
A royal dredger fails
King Willem I of the Netherlands took a personal part in building a steam dredging mill. It was finished in 1824 and sent to deepen the harbor of Antwerp, but its boiler soon exploded, and even after repair it never worked properly. Until the mid-1800s most dredging in the Low Countries was still done by hand with the dredging brace, a long pole with a leather bag.
LessonRoyal IHC notes that the earliest steam bucket dredgers were very unreliable, so steam replaced muscle only slowly.
Credit
King Willem I
2009
Jumbo hoppers hold 46,000 m³
A trailing suction hopper dredger sucks sand through a pipe dragged along the bottom while it sails, so it can work without blocking shipping. Royal IHC says the type was hardly used before the 1960s and then spread worldwide as ships grew. Jan De Nul's Cristóbal Colón, built in 2009, holds 46,000 m³ in its hopper and can dredge as deep as 155 m, by the company's figures. Guinness World Records lists it as the largest trailing suction hopper dredger, a record matched but not broken by its sister ship Leiv Eiriksson.
Credit
Jan De Nul Group..pdf)
2021
A cutter dredger burns gas
A cutter suction dredger grinds hard ground with a rotating cutter head and pumps it away through a pipeline. DEME's Spartacus, handed over by the Dutch shipyard Royal IHC on August 3, 2021, has 44,180 kW installed and main engines that can run on liquefied natural gas (LNG) as well as fuel oil. DEME calls it the first cutter suction dredger able to run on LNG. Wikipedia, citing trade press, lists it as the most powerful cutter suction dredger in the world as of 2024. Its first job was a port and land reclamation project at Abu Qir, Egypt.
Credit
DEME; Royal IHC
2021
Decks awash, then capsized
On February 17, 2021, the dredger Margrethe Fighter, loading mud with an onboard excavator in the Port of Trelleborg, Sweden, capsized on its way to the dump site, and its master died. Denmark's accident investigation board found it was sailing heavily laden with its forward ballast tanks still full. The crew filled those tanks to tip the bow down so the excavator could reach deeper, and had come to sail with water on the foredeck as routine; survivors recalled no draft readings or stability calculations on board.
Lessona loading habit that worked every day had used up the vessel's margin of stability without anyone measuring it.
Credit
Danish Maritime Accident Investigation Board (investigation)
Watch for
A methanol-ready mega hopper
Royal IHC handed the 31,000 m³ trailing suction hopper dredger SEAWAY to Boskalis on July 20, 2026, after sea trials. By the builder's account it is diesel-electric, with Azipod propulsion, and "prepared for operation on (green) methanol."
Achieved whenSEAWAY dredges on methanol on a working project, and an outside party, such as its classification society, reports the fuel burned and the emissions per cubic meter dredged.
Claimed by
Royal IHC and Boskalis, July 2026
Barges steered from shore
The Danish dredging firm Rohde Nielsen fitted remote-operation systems from MAHI Maritime Autonomy Systems to Hugin R and Munin R, split hopper barges that carry dredged material, and set up a remote operation center in Grenaa. The companies say the first sea trials outside Grenaa port succeeded.
Achieved whenthe barges carry dredged material on a paying job under control from shore, with the flag state or a classification society approving the setup and a public record of the trips.
Claimed by
Rohde Nielsen and MAHI, December 2025
Open
01
A public hopper-loading test bench
An open simulator of a hopper dredger's loading phase, when the drag head sucks up sand and the hopper fills until water and fine sediment spill overboard. It should have a standard interface, so anyone can plug in a controller that sets sailing speed, pump flow and when to stop loading, and a scoring script for payload per hour, sediment lost overboard and energy used.
The briefCredit · unclaimed02
Tally every dredger loss
A public table of every capsize, sinking and serious flooding of a dredger or hopper barge that a national accident investigator has reported. Each row gives vessel type, what it was doing, the cause, and the check that would have caught it, and links to its report.
The briefCredit · unclaimed
Open 01 · the brief
A public hopper-loading test bench
The first to publish is credited on this line, and the deliverable moves from Open to Achieved.
What to build
An open simulator of a hopper dredger's loading phase, when the drag head sucks up sand and the hopper fills until water and fine sediment spill overboard. It should have a standard interface, so anyone can plug in a controller that sets sailing speed, pump flow and when to stop loading, and a scoring script for payload per hour, sediment lost overboard and energy used.
Why it is still open
Royal IHC tested its Mission Master control layer for hopper dredgers on its own full-mission simulator and says deployment on working hoppers is the next step. TU Delft's open-source OpenCLSim schedules whole dredging cycles, not the loading process inside one. A 2023 Hohai University and Cardiff University paper trained a reinforcement learning controller for a cutter suction dredger on operating data that is available only on request. A GitHub search found production models but no public loading environment with scored controllers.
Built with what exists
Python; the Gymnasium interface used for reinforcement learning tests; Stable-Baselines3 for learned controllers; loading physics from the open TSHD_production_estimation model on GitHub and the TU Delft thesis on loading-phase energy written with Van Oord; an AI coding agent.
First step
Wrap the TSHD_production_estimation model in a Gymnasium environment and run a fixed-speed baseline on one sand type.
Done looks like
A public repository whose simulator reproduces one published loading curve to within 10%, and a table comparing a rule-based baseline with at least one learned controller over 1,000 simulated loads.
Open 02 · the brief
Tally every dredger loss
The first to publish is credited on this line, and the deliverable moves from Open to Achieved.
What to build
A public table of every capsize, sinking and serious flooding of a dredger or hopper barge that a national accident investigator has reported. Each row gives vessel type, what it was doing, the cause, and the check that would have caught it, and links to its report.
Why it is still open
The reports sit with separate national boards. The UK's Marine Accident Investigation Branch reported on the suction dredger Arco Arun, which grounded in the Thames in 1998 and capsized 43 hours later. The US National Transportation Safety Board found that undetected flooding through an open through-hull pipe capsized the dredge WB Wood on the Mississippi in January 2023. A search found single reports but no combined analysis.
Built with what exists
Report PDFs from the MAIB, NTSB, Danish Maritime Accident Investigation Board, Dutch Safety Board, Australian Transport Safety Bureau and Transportation Safety Board of Canada; pdftotext to extract text; an AI model to draft each row for a person to check; a web agent to find reports (see the Note "Deleting 80% to start over").
First step
List every MAIB and NTSB report with "dredge" or "dredger" in its title, leaving out fishing vessels called scallop dredgers, and code the first 20.
Done looks like
At least 100 incidents from at least five investigators, with a second person re-coding 20 rows and the agreement rate published.