BRENNEN

Industries / Food, farming and forestry / Agriculture and farming / Cotton ginning

Drying and cleaning

Getting seed cotton (cotton as picked, fiber still on the seed) out of the module, drying it, and cleaning out sticks, leaves, soil and plastic before and after the gin stand.

7

Milestones achieved, from 1930s to 2022.

1

To watch for: announced, not yet confirmed outside.

2

Open deliverables. Nobody has shipped them.

The road

AchievedWatch forOpen

Achieved

  1. 1930s

    Dryers for damp cotton

    As hand-picking gave way to faster, rougher snapping and stripping, seed cotton reached the gin wetter and dirtier. Tower dryers, which blow heated air through seed cotton as it zigzags down a tall shaft, were developed by the US Department of Agriculture (USDA) and taken up by gins in the 1930s so that the cleaners could handle damp cotton.

    cotton.org

    Credit

    USDA ginning engineers, as recorded by USDA-ARS authors Sidney Hughs and colleagues in 2020

  2. 1972

    Lint cleaners cost fiber

    By the 1960s most US gins had at least two stages of drying, several of seed-cotton cleaning and at least two of lint cleaning, to cope with machine-picked cotton. Measurements then showed the price: for every 227 kg of lint leaving the gin stand, the first saw-type lint cleaner removes about 8.9 kg of material and the second about 3.7 kg more, and 25.5% and 30.4% of that material is fiber (Mangialardi, 1972); samples from commercial gins showed the first lint cleaner shortening fiber by 0.4 mm and the second by 0.2 mm more (Whitelock and others, 2011).

    Lessongins should use the least drying and lint cleaning that still gives the highest bale value, because each extra pass removes saleable fiber.

    cotton.org

    Credit

    measurements by Mangialardi and later USDA-ARS teams, summarized by Robert Hardin and colleagues of USDA-ARS and Cotton Incorporated in 2018

  3. 1974

    Cotton arrives in modules

    Lambert Wilkes of Texas A&M University developed the cotton module builder between 1971 and 1974, with support from J. K. "Farmer" Jones of Cotton Incorporated; it presses seed cotton into a large free-standing block in the field, so pickers no longer wait for trailers to come back from the gin. Calvin Parnell of the Texas Agricultural Extension Service spread it through demonstrations, and the 2002 landmark plaque of the American Society of Agricultural and Biological Engineers (ASABE) says it is used for more than 90% of the US crop. USDA-ARS says feeding gins from modules raises ginning capacity by 10 to 25%, because the flow of cotton is steady.

    asabe.orgars.usda.gov

    Credit

    Lambert Wilkes, Texas A&M University; Cotton Incorporated

  4. 1998

    Sensors choose the cleaning

    W. Stanley Anthony, Richard Byler and Oliver McCaskill of the USDA-ARS ginning laboratory at Stoneville, Mississippi, built a control system that measures the color, trash and moisture of cotton as it moves through the gin and routes it around dryers, cleaners and lint cleaners it does not need. In field tests from 1994 to 1997 USDA counted $10 to $20 more per bale for farmers and nearly $1 per bale less energy for the gin. Zellweger Uster licensed the patents and sold it as IntelliGin from 1998; by its own count it ran at 33 gins by 2001, up from 110,000 bales processed in 1997 to over 1,000,000 bales in 2000/2001.

    agresearchmag.ars.usda.govcotton.org

    Credit

    USDA-ARS Stoneville; Zellweger Uster

  5. 2008

    Gin dust measured again

    Air permits for gins rest on emission factors, published estimates of dust released per bale. The US Environmental Protection Agency's (EPA) 1996 factors for gins were given low quality ratings because they came almost entirely from one region, and some gin systems had no factor at all. In 2008 ginner associations, state and federal regulators, Oklahoma State University and USDA-ARS began sampling exhaust stacks at gins across the cotton belt; for one system, second-stage lint-cleaner trash, they measured 0.0081 kg of fine dust (PM10, particles under 10 micrometers) per 227-kg bale, below the EPA figure of 0.060 kg for the combined system.

    Lessonfactors drawn from one region can set the rules for a whole industry until someone measures the rest.

    cotton.org

    Credit

    Michael Buser (Oklahoma State University) and USDA-ARS colleagues

  6. 2019

    Cameras blow out plastic

    Plastic wrap from round modules and field litter that gets into bales lowers their value. Mathew Pelletier, Greg Holt and John Wanjura of USDA-ARS at Lubbock, Texas, built a system of low-cost color cameras over the gin-stand feeder that fires air jets to blow plastic out of the cotton stream, and ran it through the whole 2019 season at two commercial gins. A 2022 USDA-ARS paper cites it as 90% effective on colored plastic, though it misses clear plastic and sits late in the gin. USDA-ARS says many of these systems are now commercially made, and in 2025 it published more than 6,000 hand-sorted images from three gins for training AI models that would calibrate the system automatically.

    cotton.orgscientificdiscoveries.ars.usda.govagdatacommons.nal.usda.gov

    Credit

    USDA-ARS Lubbock; commercial partners Lummus and Bratney

  7. 2022

    A plastic cleaner tested

    Handan Goldenlion of Hebei, China, built a contamination cleaner to strip mulch film and other plastic from Chinese seed cotton before ginning. USDA-ARS and Cotton Incorporated tested it on plastics found in US cotton: it caught more than a standard stick machine and inclined cleaner, and raising its airflow from 17,500 to 30,200 cubic meters per hour lifted plastic capture from 16% to 48%, but also raised the seed cotton thrown out with the plastic from 1.4 to 34 kg per bale. Stiff three-layer module wrap was poorly removed.

    Lessonair strong enough to lift plastic also lifts cotton, so a cleaner's capture rate means little without its cotton loss.

    cotton.org

    Credit

    Derek Whitelock and colleagues, USDA-ARS Mesilla Park and Cotton Incorporated

Watch for

  1. India targets cleaner lint

    India's cabinet approved a Mission for Cotton Productivity of Rs 5,659.22 crore for 2026-27 to 2030-31, which is to modernize about 2,000 ginning and processing factories and bring contamination below 2%, with lint sold under the Kasturi Cotton Bharat brand.

    Achieved whenan audit or survey outside the ministry counts the factories upgraded and measures contamination in their lint.

    eng.ruralvoice.in

    Claimed by

    Government of India, as reported in May 2026

Open

  1. 01

    One table of cleaning trials

    An open table of every published test of how gin dryers, seed-cotton cleaners and lint cleaners change cotton: one row per machine stage per test, with machine type, settings, cotton type, moisture, and the measured change in fiber length, uniformity, neps (small fiber knots), trash and lint lost, each row linked to the page it came from.

    The brief
    Credit · unclaimed
  2. 02

    Dust readings outside the gin

    A full season of public, calibrated readings of fine dust (PM2.5 and PM10) at the fence lines of working gins, one sensor upwind and several downwind, set up on land where the gin owner or neighbor has given permission, away from any machinery, and posted hourly with wind direction.

    The brief
    Credit · unclaimed

Open 01 · the brief

One table of cleaning trials

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

An open table of every published test of how gin dryers, seed-cotton cleaners and lint cleaners change cotton: one row per machine stage per test, with machine type, settings, cotton type, moisture, and the measured change in fiber length, uniformity, neps (small fiber knots), trash and lint lost, each row linked to the page it came from.

Why it is still open

The results are spread over 50 years of papers. The 2018 USDA-ARS and Cotton Incorporated review that sums them up gives prose and selected figures but no combined dataset, and USDA's Ag Data Commons holds one file per study, such as the 2024 lint-cleaner uniformity data.

cotton.orgagdatacommons.nal.usda.gov

Built with what exists

The Journal of Cotton Science archive and Beltwide Cotton Conferences proceedings, both free on cotton.org; pdftotext; a low-cost AI model run over every paper to pull numbers out of tables (see the Note "The jobs agents repeat"); Python and pandas; Zenodo for hosting.

  1. First step

    Extract the tables from ten lint-cleaning papers in the Journal of Cotton Science and publish the first 100 rows with a data dictionary.

  2. Done looks like

    At least 500 rows from at least 60 papers, each with a page reference; a person rechecks a random 10% of rows against the papers and publishes the error rate, which is under 2%; and the table reproduces two published figures, such as the 0.4 mm length loss at the first lint cleaner.

Open 02 · the brief

Dust readings outside the gin

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

A full season of public, calibrated readings of fine dust (PM2.5 and PM10) at the fence lines of working gins, one sensor upwind and several downwind, set up on land where the gin owner or neighbor has given permission, away from any machinery, and posted hourly with wind direction.

Why it is still open

Gin dust rules rest on emission factors: dust per bale measured in exhaust stacks. The industry project begun in 2008 also sampled the air around each gin it tested, but in campaigns of about 15 days with 12 sampling towers, to work out those factors. In 2012 Texas AgriLife Research modeled gins of 20 to 60 bales an hour and found that, with the emission factors used, PM10 and PM2.5 at the property line would exceed the US national air standards. I found no season-long public record of measured dust at a gin's fence line.

cotton.orgcotton.orgcotton.org

Built with what exists

Low-cost laser particle sensors such as PurpleAir outdoor units or Sensirion SPS30 boards; solar panels and cellular modems; a small weather station for wind; side-by-side calibration against a government reference monitor; Python for the correction.

  1. First step

    Run four sensors next to a government reference monitor for two weeks and publish the calibration.

  2. Done looks like

    Three gins, at least four sensors each, through one ginning season (75 to 120 days, by the 2014 paper's figure), with over 90% of hours captured, the calibration fit against a reference monitor published, and the full dataset open.