Industries / Food, farming and forestry / Agriculture and farming / Cotton ginning
Baling
Baling presses clean lint into a dense block, wraps it and ties it so it can be stored, sampled, shipped and opened at a mill.
6
Milestones achieved, from 1801 to 2026.
1
To watch for: announced, not yet confirmed outside.
2
Open deliverables. Nobody has shipped them.
The road
AchievedWatch forOpen
Achieved
1801
Mules turn a screw press
The earliest packers tramped and pounded lint into a hanging bag until it reached about 5 lb per cubic foot, one bag per man per day. Perry John Freeman's 1916 University of Illinois thesis says the first screw press was brought in by William Dunbar, a Mississippi planter, in 1801: mules walked long sweeps that drove a wooden screw down onto the lint, and half a dozen men made five to eight bales a day at 7 to 8 lb per cubic foot, tied with hemp rope. Iron hoops began to replace rope about 1846, over cotton merchants' objections.
Credit
William Dunbar; account by Perry John Freeman
1902
The round bale fails
John R. Fordyce's press wound the lint batt around a core into a tight roll of 35 to 40 lb per cubic foot that needed no ties. Freeman's 1916 thesis records nearly a million round bales in 1902 and 57,618 in 1914: they packed badly on ships, mills needed special machinery to open them, and buyers could not cut samples from the tightly rolled layers.
LessonA bale has to suit ships, mills and samplers, not only the gin.
Credit
John R. Fordyce
1955
Samples drawn during ginning
Buyers used to cut holes in two sides of each finished bale to pull a grading sample, which left ragged, dirty bales. USDA researchers developed a mechanical sampler that takes lint from the stream during ginning, and makers began building them in 1955, but a 1960 USDA report counted them in only about 153 gins, over 90% of them in Texas and California, and a 1964 USDA report said many industry leaders still opposed them. By 2022 the National Cotton Council said most samples were cut and pulled at the press before the bale is covered, instead of through the bagging.
LessonBuyers accepted samples taken by machine only after years of side-by-side tests against cut samples.
Credit
US Department of Agriculture researchers
1985
Gins press to shipping density
From about 1870 gin presses made bales of about 12 lb per cubic foot, and these were pressed a second time at large "compresses" at shipping centers to the density shippers asked for (Freeman, 1916). The gin universal density (UD) bale, pressed once at the gin to about 28 lb per cubic foot, 54 to 55 inches long, 20 to 21 inches wide and about 500 lb, removed that second step. William Mayfield reported about 65% of the 1985 US crop packed in UD bales at the gin, USDA's Agricultural Research Service (ARS) put the share at about 96% in 1996, and the National Cotton Council says gin UD bales now make up all of the US crop.
Credit
US ginners and gin press makers; shares reported by William Mayfield and USDA ARS
2006
Wet bales leave the loan
Many gins spray water on the lint just before the press, because moist lint presses with less force and breaks fewer ties, but too much water spoils fiber during storage. The National Cotton Council's Quality Task Force set 7.5% moisture as a ceiling in 2004, and USDA researcher Richard Byler reports that in 2006 USDA's Farm Service Agency defined a wet bale, which its marketing loan program does not accept, as one at or above 7.5% moisture on a wet basis (water as a share of total weight) at any point in the bale at the gin. In Byler's 2013 study of 731 bales, bales given added moisture averaged 1.1 percentage points wetter than the meter in the lint flue had read.
LessonWater added to ease pressing has to be measured in the bale, not before it.
Credit
National Cotton Council; USDA Farm Service Agency
2026
India withdraws its bale order
India's Ministry of Textiles issued the Cotton Bales (Quality Control) Order on 28 February 2023 to make ginning and pressing factories certify their bales to Indian Standard IS 12171:2019, which covers packing, weight, labeling, moisture and trash. It was deferred four times, and by a regulatory tracker's account it was rescinded on 9 June 2026 by notification S.O. 2956(E). Fibre2Fashion reported in July 2025 that small ginning units opposed it because meeting the norms needed costly new machinery.
LessonA mandatory bale standard stalls when most gins cannot afford the equipment to meet it.
Credit
Ministry of Textiles, India
Watch for
Older bale wraps phased out
The Joint Cotton Industry Bale Packaging Committee (JCIBPC), the US body that approves bale bagging and ties, voted 24 to 2 on 7 October 2025 that woven polypropylene bagging will be eligible for the government loan only through 2031, and that wire ties will be limited to export bales from 2031. Its 2022 guide already said plastic strapping was overtaking wire ties.
Achieved whenthe committee's specifications for the 2032 crop no longer list woven polypropylene bagging as loan-eligible and allow wire ties only on export bales.
Claimed by
JCIBPC, October 2025
Open
01
Grade bale wrapping from photos
A phone app that photographs a bale's sides and ends as it arrives at a warehouse or mill and sorts it into the JCIBPC's Grade A, Grade B or Other, naming the defect it sees: torn bagging, exposed or dirty lint, open ends, ties not sunk into the bale, wire knots on a flat side, rust, oil, or a missing bale tag.
The briefCredit · unclaimed02
Score meters against wet spots
A public test of whether the bale moisture meters gins use today catch the bales that the loan rule calls wet: bales mapped layer by layer with oven samples, then read with each meter, with the results published.
The briefCredit · unclaimed
Open 01 · the brief
Grade bale wrapping from photos
The first to publish is credited on this line, and the deliverable moves from Open to Achieved.
What to build
A phone app that photographs a bale's sides and ends as it arrives at a warehouse or mill and sorts it into the JCIBPC's Grade A, Grade B or Other, naming the defect it sees: torn bagging, exposed or dirty lint, open ends, ties not sunk into the bale, wire knots on a flat side, rust, oil, or a missing bale tag.
Why it is still open
The JCIBPC's 2022 "Guide for Cotton Bale Standards" is a set of photographs that inspectors compare by eye. USDA ARS's 2025 bale-camera project photographs bales at the press to estimate fiber quality, not packaging. Searches of GitHub and Crossref in November 2026 found a bale-detection repository and papers on bale size inside cotton pickers, but no packaging grader.
Built with what exists
Phone cameras; open object-detection and segmentation models such as Ultralytics YOLO or Meta's Segment Anything; Label Studio for labeling; the JCIBPC guide's photographs as the reference set.
First step
With a warehouse's permission, photograph 100 bales at receiving from four sides and have one inspector grade each against the guide.
Done looks like
On 1,000 bales photographed at two warehouses and graded independently by two experienced inspectors, the app agrees with the inspectors' grade on at least 90% of bales and catches at least 95% of the bales they put in "Other".
Open 02 · the brief
Score meters against wet spots
The first to publish is credited on this line, and the deliverable moves from Open to Achieved.
What to build
A public test of whether the bale moisture meters gins use today catch the bales that the loan rule calls wet: bales mapped layer by layer with oven samples, then read with each meter, with the results published.
Why it is still open
Wet spots are known. In a 2006 study led by USDA ARS that sampled bales layer by layer, moisture was uneven in sprayed bales and grew spottier as more water was added. ARS found moisture from below 7% to above 13% within single commercial bales, and in 2008 ARS engineer Mathew Pelletier and Cotton Incorporated's Edward Barnes reported a prototype that maps moisture through a whole bale with microwave beams. But the meter studies (50 bales with a microwave meter in 2008, 731 bales in 2013, 534 in 2014) compared meter readings with oven tests from one or two spots per bale, and I found no published test of how often today's meters miss a bale that has a spot at or above 7.5%.
Built with what exists
The oven method (weigh, dry, reweigh) with a lab oven and balance; a hand coring tool used through the bagging without cutting the ties; a Delmhorst probe meter and a microwave meter such as the Vomax 851-B; Python for the maps. The bales come from a research or commercial gin; no one operates the press.
First step
Ask a USDA ginning laboratory or a university research gin for five bales made with moisture restoration and core them at 30 marked positions.
Done looks like
20 bales, 30 oven samples each from marked positions, maps published with the raw data, and for each meter the share of bales with any spot at or above 7.5% that it flagged.