BRENNEN

Industries / Technology / Electronics and semiconductors / Contract electronics manufacturing

Board assembly

This work prints solder paste onto bare circuit boards, places the parts on them by machine and melts the solder in an oven so that every joint is made in one pass.

5

Milestones achieved, from 1973 to 2019.

1

To watch for: announced, not yet confirmed outside.

2

Open deliverables. Nobody has shipped them.

The road

AchievedWatch forOpen

Achieved

  1. 1973

    Soldering in boiling vapor

    Robert C. Pfahl Jr. of Western Electric filed a patent in September 1973, granted in February 1975, for heating a board in the vapor of a boiling inert liquid: the vapor condenses on the board and gives up its heat, so no part can get hotter than the liquid's boiling point. A paper by Allen W. Duck of A-Tek, a maker of vapor-phase machines, says the method was widely used in the early years of surface mounting, until ozone-depletion concerns, the cost of the fluids and the difficulty of fitting it into conveyor lines let infrared and then convection ovens, which blow heated air over the board, take over.

    Lessonthe method with the better heating lost to ovens that were cheaper to run and easier to put on a line, and it survives for heavy and costly boards.

    patents.google.comsmtnet.com

    Credit

    Robert C. Pfahl Jr., Western Electric

  2. 1981

    Machines place surface parts

    Fuji Machine Manufacturing of Japan, until then a maker of lathes and assembly machines, completed its first CP-I chip placer in 1981. In 1985 its CP-II added what Fuji calls the industry's first vision recognition on a high-speed placer, in which a camera checks how each part sits on the pickup nozzle before it is set down, and by 1994 its CP-6 placed a part every 0.09 seconds, by Fuji's figure.

    fuji.co.jp

    Credit

    Fuji Machine Manufacturing (now FUJI Corporation)

  3. 1985

    Reflow cracks plastic packages

    In reflow soldering the whole board passes through an oven. As Japanese factories moved to it for surface-mount parts, the plastic bodies of the chips began to crack and their fine gold wires to break, and the Semiconductor History Museum of Japan dates to 1985 the ultrasonic inspection developed to find the damage.

    Lessonheating the whole board in an oven stresses the parts themselves, not only the joints; IPC and JEDEC's joint standard J-STD-020 now rates each plastic part's sensitivity to moisture-induced stress so that it is stored and handled to avoid damage in reflow.

    shmj.or.jpjedec.org

    Credit

    Japanese chipmakers

  4. 1991

    Outsourcing wins a quality prize

    Solectron, founded in 1977 as a small assembly job shop in California, won the US Malcolm Baldrige National Quality Award in 1991 and again in 1997. NIST's 1991 profile says board assembly made up about 80% of its business, that its defect rate had fallen to 233 parts per million, and that major computer makers had closed their own assembly lines after finding that sending the work to Solectron lowered cost and also improved quality.

    Lessoncustomers handed board assembly to a contractor for quality as well as for price.

    nist.govnist.gov

    Credit

    Solectron Corporation, led by Ko Nishimura

  5. 2019

    Assembly by web order

    In September 2019 JLCPCB, a circuit board maker in Shenzhen, opened its surface-mount assembly service to buyers outside China. One of the first overseas buyers reported on the EEVblog forum that the parts for 10 boards cost about $60 and the assembly about $24, with limits: parts on one side only, no through-hole parts, and parts only from the firm's own library.

    eevblog.com

    Credit

    JLCPCB

Watch for

  1. Feeders that load themselves

    A feeder holds a reel of parts on tape and presents them to the placement machine, and loading reels into feeders, called kitting, is still mostly done by hand. Panasonic says its Auto Setting Feeder peels the cover tape off tapes 4 mm to 104 mm wide and loads them into its NPM-GW placer without a person, as part of an "autonomous factory" it says customers such as Incap UK and ZF Automotive have deployed. Fuji says its Auto Kitting Station, shown in Tokyo in June 2026, removes empty reels, reads reel IDs and loads 8 mm tape into feeders, a job it says has been "heavily dependent on manual labor". Neither gives a count of how often a person still steps in.

    Achieved whena contract manufacturer or an outside reporter publishes a production run of at least one full shift with reels loaded per hour, wrong loads and the number of times a person handled reels or feeders.

    eu.connect.panasonic.compcbdirectory.com

    Claimed by

    Panasonic, November 2025; Fuji, June 2026

Open

  1. 01

    Tombstone check, proven on boards

    A KiCad script that measures, for each small two-pad part, how much copper is joined to each pad (trace widths, plane connections, vias) and flags parts whose two ends will heat unevenly in the oven, which can make the part stand up on one end, a defect called a tombstone. Then a test board that puts 0402 and 0201 resistors (1.0 mm and 0.6 mm long) on pads with ten graded levels of imbalance, built by two low-cost assembly services, to find where tombstones start.

    The brief
    Credit · unclaimed
  2. 02

    First board checked from files

    Software that takes a board's placement file and parts list from its design files, plus one overhead photo of the first assembled board, and reports for every part whether it is present, turned the right way and marked as the parts list says. It needs no known-good "golden" board and no inspection program written by hand.

    The brief
    Credit · unclaimed

Open 01 · the brief

Tombstone check, proven on boards

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

A KiCad script that measures, for each small two-pad part, how much copper is joined to each pad (trace widths, plane connections, vias) and flags parts whose two ends will heat unevenly in the oven, which can make the part stand up on one end, a defect called a tombstone. Then a test board that puts 0402 and 0201 resistors (1.0 mm and 0.6 mm long) on pads with ten graded levels of imbalance, built by two low-cost assembly services, to find where tombstones start.

Why it is still open

Designed experiments on tombstoning have been published for years; a Jabil study of 0201 parts in lead-free solder, reported in Circuits Assembly in 2007, lists thermal balance between pads as a design factor but found paste and placement offsets the top contributor to defects. PCB-Investigator, a commercial tool, added a tombstone analysis in April 2026 that lists the difference in pad connection between pin 1 and pin 2, but the user sets the threshold and the page cites no measurements linking a difference to a tombstone rate. We found no open KiCad check, and no published test of whether such a check predicts tombstones on low-cost assembly services.

circuitsassembly.compcb-investigator.com

Built with what exists

KiCad and its Python scripting (pcbnew); a low-cost board assembly service such as JLCPCB; a USB microscope; a spreadsheet.

  1. First step

    Draw the test board with ten imbalance levels for each part size and post the design before ordering.

  2. Done looks like

    at least 4 boards from each of 2 services with 400 parts each, every tombstone counted and photographed, a published curve of tombstone rate against imbalance, and the script's score on those boards: the share of parts that tombstoned that it flagged, and the share of sound parts it flagged, with the threshold fixed before the boards were built.

Open 02 · the brief

First board checked from files

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

Software that takes a board's placement file and parts list from its design files, plus one overhead photo of the first assembled board, and reports for every part whether it is present, turned the right way and marked as the parts list says. It needs no known-good "golden" board and no inspection program written by hand.

Why it is still open

Robovision says automated optical inspection (AOI) machines can take up to two hours to set up for each new board in low-volume work, and its own camera system needs the board's Gerber files plus photos of a golden board. EDGE INSPECT, a contest project posted in October 2026, compares a detector's findings in a phone photo with the parts list, placement file and Gerber files and reports missing, misplaced and unexpected parts, but it sorts parts only by kind, such as resistor or capacitor, and publishes no detection rate. An open first-article tool posted the same month shows each placement to a person, who marks it good or bad with the keyboard.

robovision.aielectronicsforu.comgithub.com

Built with what exists

KiCad's placement and parts-list exports; a phone or USB microscope camera on a copy stand; OpenCV to line the photo up with the placement file; an AI model that reads images, such as Claude Fable 5.2 (see the Note "Three working devices") or an open-weight vision model.

  1. First step

    Photograph one assembled open-hardware board, export its placement file and line the two up.

  2. Done looks like

    20 assembled boards carrying 60 errors planted by someone other than the builder (missing parts, parts turned 180 degrees, wrong values), with the share of errors found, false alarms per board and minutes per board published, and the code public.