Industries / Construction and property / Commercial and residential construction / ConTech
Robots
This work is making, selling and renting machines that do a physical building task themselves, such as laying brick, tying steel bars, welding columns or walking a site to record progress, usually with a person nearby who loads, watches and checks them.
5
Milestones achieved, from 1991 to 2021.
3
To watch for: announced, not yet confirmed outside.
3
Open deliverables. Nobody has shipped them.
The road
AchievedWatch forOpen
Achieved
1991
A factory on the roof
Shimizu turned the top of a rising steel building into a covered factory: the Juroku Bank building in Nagoya, Japan, 20 stories above ground and 88 m tall, started in October 1991. Under the cover, hoists and cranes moved steel, floor planks and wall panels, robots welded the steel joints, and the whole platform was jacked up one story at a time as floors were added beneath it. Shimizu's own paper says the work the system handled took about 50% less labor and produced 70% (700 t) less waste. An outside review by Brian Potter (Construction Physics, 2021) reports that Shimizu found a 15% shorter build period, and that at least 60 uses of such automated sites in Japan have been recorded. Potter dates the building to 1991; Shimizu's paper says its system part was finished in autumn 1993.
LessonEach automated site served one building at a time and cost a great deal to set up, and Potter found none of these systems still in use in 2021 apart from Shimizu's newer work.
Credit
Shimizu Corporation (paper by J. Maeda, 1994); Obayashi (ABCS) and Kajima (AMURAD) built similar systems
2015
A robot lays brick
SAM, the Semi-Automated Mason, lifts and places bricks on a wall while a mason works alongside it and laborers keep it supplied. In 2015 Clark Construction used one on a new school building for The Lab School in Washington, D.C. Construction Robotics said a mason working with SAM can lay two to four times as much brick (the company's figure). In 2019 the company's co-founder Scott Peters told Building Design + Construction that more than 130 of its MULE machines, which lift heavy blocks so the mason can place them, and 11 SAMs were in the field. Tyler Shawcross, Clark's senior project manager on a 2019 Navy barracks job that used the company's machines, said: "I don't think it's a large cost reducer, but it could be a scheduling reducer."
LessonBy the maker's own count, the simpler machine that only takes the weight of a block spread more than ten times as far as the robot that lays brick.
Credit
Construction Robotics of Victor, New York (co-founder Scott Peters)
2017
A robot ties bridge steel
Concrete bridge decks hold a grid of steel reinforcing bars (rebar), and every crossing has to be tied with wire, a job done bent over by hand. TyBot is a gantry that spans the deck and moves an arm over each crossing to tie it. It debuted on the Freedom Road bridge in Beaver County, Pennsylvania, in 2017 with Brayman Construction, tying over 24,000 crossings at 5.5 seconds each (ENR's figures). A state highway official, Jim Foringer of PennDOT District 11, said: "What we especially like is that the ties were very tight." The Texas Department of Transportation first used it in May 2022 on SH 302 in Winkler County and says it can tie up to 1,100 crossings an hour.
Credit
Advanced Construction Robotics, founded in 2016 by Stephen Muck of Brayman Construction and Jeremy Searock, formerly of Carnegie Mellon University's National Robotics Engineering Center
2021
Welding robots in Tokyo
Shimizu showed three site robots in Tokyo on April 23, 2018: Robo-Welder, which uses lasers to read the groove it must weld on a steel column; Robo-Carrier, which moves materials along a set route; and Robo-Buddy, which places and fixes boards on ceilings and floors (Associated Press; Global Construction Review). In February 2021 the Nikkan Kogyo Shimbun newspaper reported Robo-Welder at work on the basement columns of the Toranomon-Azabudai Project in Minato, Tokyo, welding steel plate 100 mm thick. The paper reported that work needing eight skilled welders per column was done by five.
LessonIn 2018 Shimizu's executive Masahiro Indo said the robots could handle "just 1 percent of overall construction work" and that reaching 10 percent "might be too costly"; robots that each do one task cover a small share of a building.
constructionequipmentguide.comglobalconstructionreview.comnewswitch.jp
Credit
Shimizu Corporation
2021
Katerra goes bankrupt
Katerra was a US start-up that called itself the architect, the engineer, the general contractor and the subcontractor of its own projects, and made building parts in its own factories: one of 250,000 square feet in Spokane, Washington, opened in 2017, and one of 200,000 square feet in Phoenix that made whole walls. It filed for Chapter 11, the US court process for reorganizing or selling off a company that cannot pay its debts, in June 2021. Construction Dive reported that it "blew through more than $2 billion of investor money, a majority from" SoftBank; an earlier Construction Dive report put SoftBank's investment at US$500 million for a majority stake. The company blamed in part the COVID-19 pandemic and the loss of bonding (guarantees that a builder will finish a job) after its former lender Greensill failed.
LessonOutside experts said Katerra tried to fix every step of building at once by buying the whole supply chain; as one architect put it, "The idea of buying your own supply chain is, now we know, a bad idea.".
Credit
Katerra, backed by SoftBank
Watch for
Humanoids walk the site
Two contractors say humanoid robots (robots built in human shape) now move around live sites on their own to record progress. Tilbury Douglas in the UK says its robot "Douglas" takes 360-degree pictures and writes progress reports, and that it should save about 40 hours a month of staff time (the company's estimate); it calls itself the first tier-one contractor (one of the largest main contractors) to do this. Shimizu in Japan says a humanoid robot carrying a camera walked the Tokiwabashi Project site on its own at 1.0 m/s, with the footage checked by AI models, as part of field trials with technical help from Sony. Ioannis Brilakis, president of the International Association for Automation and Robotics in Construction, called this kind of record-keeping "low-hanging fruit."
Achieved whensomeone outside the contractor, such as a client, insurer or university, publishes measured results from months of use on live sites, such as hours saved or the share of planned walks finished without a person stepping in.
Claimed by
Tilbury Douglas, April 2026; Shimizu Corporation, July 2026
Robots tie vertical rebar
TyBot works on flat bridge decks. The steel in walls and columns stands upright, and that is the case this research targets. A team at the Hong Kong Center for Construction Robotics (HKUST) built OpenTie, a UR5e robot arm with a camera and a rebar-tying tool (a Makita DTR181 rewired so the robot can trigger it). In 150 lab trials across 10 set-ups, it tied the target crossings in 92.7% of trials, with a mean position error of 1.95 mm (the authors' figures). The lab was built to look like a real site, and the authors say real-site tests are the next step.
Achieved whenthe system ties a real wall or column cage on a working site and someone outside the team, such as the contractor or an independent tester, reports the success rate.
Claimed by
Sai Fan, Yanke Wang and colleagues, HKUST, August 2025 (revised June 2026)
A painting arm copies workers
Shimizu says it has started field trials of a robot arm that learns painting by imitating human painters, part of a company project to put AI-driven robots on its sites. It gave no figures for speed or quality.
Achieved whensomeone outside Shimizu measures the arm's paint thickness and coverage against human painters' work over a full job on a live site.
Claimed by
Shimizu Corporation, July 2026
Open
01
Set ceiling tiles by robot
A low-cost robot arm on a stand that picks up a lay-in ceiling tile, tilts it up through an opening in a T-bar grid (the metal grid of a suspended ceiling), and lowers it flat onto the grid, the way a ceiling fitter does by hand.
The briefCredit · unclaimed02
Pull wire through conduit
A bench rig with a run of empty steel tubing (conduit) with two right-angle bends, and a robot that pushes a fish tape (a flexible steel guide wire) through it, fastens loose wires to its end, and pulls them back. No wire is connected to power at any point.
The briefCredit · unclaimed03
Seal pipe gaps against fire
A robot arm holding a battery caulking gun that follows the ring-shaped gap around a pipe passing through a mock fire-rated wall and fills it with fire-stopping sealant (sealant that swells in heat to block fire and smoke) to a set depth.
The briefCredit · unclaimed
Open 01 · the brief
Set ceiling tiles by robot
The first to publish is credited on this line, and the deliverable moves from Open to Achieved.
What to build
A low-cost robot arm on a stand that picks up a lay-in ceiling tile, tilts it up through an opening in a T-bar grid (the metal grid of a suspended ceiling), and lowers it flat onto the grid, the way a ceiling fitter does by hand.
Why it is still open
Ci-Jyun Liang, Vineet Kamat and Carol Menassa taught a robot this task from human demonstrations, but tested it in a computer simulation with an imitation KUKA industrial arm: 78% success across 60 simulated scenes (2020). A 2023 follow-up by Hongrui Yu, Kamat and Menassa at the University of Michigan drove a real KUKA KR120, an industrial arm that carries 120 kg, but called its runs "preliminary simulation robot experiments," ran five repeats per test, and repeated the batches with lower success in simulation to avoid damaging the tiles. No physical tally with a low-cost arm has been published.
Built with what exists
An SO-101 arm (US$121.94 in parts for one arm, RobotStudio's figure) with thin 0.013-inch tiles such as Ceilume Feather-Light, which fit a standard 15/16-inch T-bar grid; or a UFactory xArm 6 (5 kg payload, from US$5,299, UFactory's figures) for heavier mineral-fiber tiles. Hugging Face's open-source LeRobot software records demonstrations and trains a policy (the program that turns camera images into arm moves), such as ACT or SmolVLA (see the Note "No download"). Robot models that learn from a handful of demonstrations are the reason this is now worth trying (see the Note "Five demonstrations per task").
First step
Build one 2 by 2 bay of 15/16-inch grid on a timber frame at table height, buy a box of tiles, and record 50 hand-guided demonstrations with the SO-101 leader arm.
Done looks like
Fifty filmed attempts on a real 2 ft by 2 ft grid, with a published tally of tiles that end flat on all four edges and within 5 mm of their place, the tolerance the Michigan studies used.
Open 02 · the brief
Pull wire through conduit
The first to publish is credited on this line, and the deliverable moves from Open to Achieved.
What to build
A bench rig with a run of empty steel tubing (conduit) with two right-angle bends, and a robot that pushes a fish tape (a flexible steel guide wire) through it, fastens loose wires to its end, and pulls them back. No wire is connected to power at any point.
Why it is still open
A 2022 US patent by Moshe Shapiro and David Klein describes the job as done today: "Currently a pair of workmen typically pull wire together," one feeding the fish tape and one attaching the wires. An October 2025 survey of robots on electrical jobsites in EC&M magazine lists drilling, layout and cable-cutting robots, but none that pulls wire, and BuiltWorlds' July 2026 list of 50 construction robot makers names none either.
Built with what exists
Two SO-101 arms run by LeRobot to learn the fiddly step of taping wires to the fish tape from demonstrations; a stepper motor with rubber pinch rollers on an Arduino board to feed and pull; a load cell to log pulling force; a steel fish tape and three insulated conductors. An AI model can write the step-by-step pull sequence as a program a person can read and check (see the Note "Readable robot programs").
First step
Build the rig and time ten pulls done by two people by hand, as the baseline to beat.
Done looks like
Twenty filmed pulls of three conductors through 6 m of tubing with two 90-degree bends, with a published tally of complete pulls in which no person touched the wire, the peak pulling force of each, and the number of wires with scuffed insulation.
Open 03 · the brief
Seal pipe gaps against fire
The first to publish is credited on this line, and the deliverable moves from Open to Achieved.
What to build
A robot arm holding a battery caulking gun that follows the ring-shaped gap around a pipe passing through a mock fire-rated wall and fills it with fire-stopping sealant (sealant that swells in heat to block fire and smoke) to a set depth.
Why it is still open
Fire-stopping sealant is applied like caulk and smoothed with a tool; one maker describes its product's "excellent caulking and tooling properties." BuiltWorlds' July 2026 list of 50 construction robot makers covers layout, drilling, installation and finishing robots, and names none that does fire-stopping or sealant work.
Built with what exists
A UFactory xArm 6 (5 kg payload, from US$5,299) holding a battery caulking gun; an Intel RealSense D435i depth camera to find the gap; LeRobot to record and train from hand-guided demonstrations; a mock wall of gypsum board on steel studs with short plastic and steel pipes passing through it; a fire-stopping sealant such as STI SpecSeal LCI.
First step
Build the mock wall with ten pipe holes and seal five by hand, cutting them open to set the human baseline.
Done looks like
Twenty sealed pipe gaps, each cut out and measured with calipers at four points, with a published tally of seals that reach the depth the sealant maker's tested system calls for and show no voids.