Industries / Consumer goods / Consumer electronics
Batteries and charging
This work covers how devices take in power: the battery inside a phone or laptop, the port and cable it charges through, the charger in the box or bought separately, wireless pads, and the rules that let one charger serve many devices. How battery cells are made and how their health is read are in the Batteries and energy storage file.
7
Milestones achieved, from 2014 to 2024.
2
To watch for: announced, not yet confirmed outside.
2
Open deliverables. Nobody has shipped them.
The road
AchievedWatch forOpen
Achieved
2014
One plug, 100 watts
USB ports have carried a 5-volt supply since the first USB specification, of January 1996. Around 2007 Qualcomm and Nokia led work on the USB Battery Charging Specification, which let a port signal that it could give phones up to 1.5 A, or 7.5 W. On 11 August 2014 the USB groups released the USB Type-C connector, a plug that fits either way up, and version 2.0 of USB Power Delivery (PD), which lets charger and device agree on higher voltages for up to 100 W; a 2017 update added fine voltage steps used for phone fast charging.
LessonFrom 2012, the IEEE milestone notes, phone makers' own fast-charging methods went beyond the 5 V, 1.5 A limit and caused interoperability problems, which a shared standard was needed to settle.,_1996).
Credit
USB Implementers Forum and its members; Qualcomm and Nokia
2018
Gallium nitride shrinks chargers
Anker launched its PowerPort Atom PD 1 in New York on 25 October 2018, a 30 W USB-C charger much smaller than Apple's 30 W iPad charger in ChargerLAB's side-by-side photos. Its power chip came from Power Integrations' InnoGaN range and used gallium nitride (GaN), a semiconductor that can switch at high frequency with low losses, so the charger's other parts could shrink. ChargerLAB, a charger testing site, called it the world's first GaN charger in its teardown.
Credit
Anker; Power Integrations
2019
AirPower is cancelled
Apple announced AirPower in September 2017, a mat promising to charge several devices at once placed anywhere on it. On 29 March 2019 Apple's head of hardware engineering, Dan Riccio, said it "will not achieve our high standards" and cancelled it; TechCrunch's Matthew Panzarino reported hearing that it ran too hot because its charging coils sat so close together.
LessonCharging anywhere on a pad proved harder than holding the phone in one spot; Apple's next design, MagSafe in 2020, used a ring of magnets to line the phone up with a single coil.
Credit
Apple
2020
The charger leaves the box
With the iPhone 12 in October 2020, Apple stopped putting a power adapter and earphones in the box, saying the smaller box let 70% more fit on a shipping pallet and cut carbon emissions. Brazil's Ministry of Justice ruled in September 2022 that this sold "an incomplete product", fined Apple more than US$2.3 million (BRL 12.2 million) and suspended sales of iPhones without a charger; Apple could appeal.
LessonA change made for the environment was read by one regulator as shifting cost onto buyers; the EU's 2022 rule instead says that a seller who offers a device with a charger must also offer it without one, and must show which with a pictogram.
Credit
Apple; Brazil's National Consumer Secretariat
2023
Silicon enters phone batteries
Lithium-ion cells have used graphite for the anode, the electrode that holds lithium when the battery is charged; adding silicon to it gives more capacity in the same space. Honor's Magic5 Pro of 2023 was the first phone with a silicon-carbon battery, by Tom's Guide's account. By April 2026 almost every flagship and mid-range phone from Chinese makers used one, with capacities from 6,000 to 10,000 mAh, while Apple, Google and Samsung had not adopted them; the 6.1 mm Honor Magic8 Pro Air holds 5,500 mAh against 3,190 mAh in Apple's iPhone Air.
LessonCost and caution still split the market; OnePlus's Rudolf Xu said he did not foresee such cells "becoming cheaper than conventional graphite-anode cells in the near term".
Credit
Honor; OnePlus, Oppo and other Chinese makers
2023
Magnets join the Qi standard
The Wireless Power Consortium (WPC), founded in 2008, publishes Qi, the main standard for charging phones on a pad. In November 2023 it launched Qi2, which adds magnets that hold the phone in line with the coil, as Apple's MagSafe had done since 2020, at 15 W; the WPC says more than 1.5 billion certified Qi2 devices and chargers were on the market within a year. In July 2025 it certified the first Qi2 25W products, and Google's Pixel 10 phones of August 2025 were built with Qi2 magnets, the Pixel 10 Pro XL charging at 25 W.
Credit
Wireless Power Consortium; Apple; Google
2024
One port by law
EU Directive 2022/2380, adopted on 23 November 2022, requires USB-C charging ports on phones, tablets, cameras, headphones, earbuds, portable speakers, handheld game consoles, e-readers, keyboards, mice and navigation devices sold from 28 December 2024, and on laptops from 28 April 2026. Devices that charge at more than 15 W must support USB PD, any extra fast-charging method must keep USB PD fully working "irrespective of the charging device used", and a seller offering a device with a charger must also offer it without one, with a pictogram showing which. Apple moved the iPhone 15 to USB-C in September 2023.
LessonIn June 2009 ten companies, among them Apple, Nokia and Samsung, signed a voluntary agreement to make phone chargers compatible through micro-USB; the law's own preamble says voluntary efforts reduced the number of chargers but did "not fully meet" the goal.
Credit
European Parliament and Council; European Commission
Watch for
More silicon in phone anodes
Honor says the fifth generation of its silicon-carbon battery, made with ATL, has 25% silicon in the anode, and 32% in the 1 TB Chinese version of its Magic V6 folding phone, which holds 7,150 mAh; OnePlus says the OnePlus 15 reaches 15% silicon and 7,300 mAh. The reporter, Myriam Joire, writes that a Google Pixel executive told her in 2025 that such batteries were not yet mature, safe or durable.
Achieved whenan independent lab publishes cycle tests of these cells showing they keep at least 80% of their capacity after 800 full cycles, the floor EU rules set for phones and tablets.
Claimed by
Honor and OnePlus, April 2026
Common charger for more devices
In a report submitted on 30 June 2026, the European Commission named seven kinds of device not yet covered by the common-charger rules whose inclusion it found would bring savings and environmental benefits without technical barriers or safety problems: smartwatches, fitness trackers, smart glasses, wristbands, AR and VR headsets, personal drones and game controllers. By 28 December 2026 it is due to report on whether cables should also be sold separately.
Achieved whenthe EU adopts an amendment that adds these devices, with a date from which it applies.
Claimed by
European Commission, June 2026
Open
01
Qi2 losses across phones
A public table of how much more energy phones take to charge on Qi2 and Qi2 25W pads than by cable, for many pairs of phone and charger. For each pair, log the energy going into the pad at its USB-C input while the phone charges from 10% to 100%, then the same for a cable through the same meter, and add runs with the phone 5 mm off center and the draw of an empty pad.
The briefCredit · unclaimed02
USB-C ports plugged 10,000 times
An open rig that plugs a USB-C cable into a phone's charging port up to 10,000 times, the life that makers such as GCT rate their bare connectors for, and every 500 cycles checks that the phone still charges, the voltage lost across the plug at a fixed current, and the force needed to pull the plug out. Run it on several phone models, with straight insertions from a motion stage and angled, off-center ones like people make from a small robot arm.
The briefCredit · unclaimed
Open 01 · the brief
Qi2 losses across phones
The first to publish is credited on this line, and the deliverable moves from Open to Achieved.
What to build
A public table of how much more energy phones take to charge on Qi2 and Qi2 25W pads than by cable, for many pairs of phone and charger. For each pair, log the energy going into the pad at its USB-C input while the phone charges from 10% to 100%, then the same for a cable through the same meter, and add runs with the phone 5 mm off center and the draw of an empty pad.
Why it is still open
The WPC says Qi2 brought an "immediate improvement in charging speed and energy efficiency" and calls Qi2 25W "remarkably fast and efficient", without published figures. The most detailed public test found covers one phone and one pad: in April 2024 iFixit measured an iPhone 15 Pro using 18.25 Wh to fill its 12.7 Wh battery by cable and 23.33 Wh on MagSafe, measured at the wall socket. A June 2026 Engadget explainer still relies on that test and an older estimate from OneZero.
Built with what exists
USB-C power meters that log energy, such as ChargerLAB's POWER-Z KM003C, which also shows which charging method a device is using; Qi2 and Qi2 25W pads certified by the WPC; phones with built-in magnets, such as iPhones with MagSafe and Google's Pixel 10 series; a 5 mm plastic spacer; Python for the analysis.
First step
Charge one phone from 10% to 100% three times by cable and three times on one Qi2 pad through the same logging meter, and compare the totals.
Done looks like
At least 10 phones from at least four makers on at least eight pads, each pair run three times, with watt-hours in, percent extra over the cable and standby draw published for every pair, and repeat runs within 3% of each other.
Open 02 · the brief
USB-C ports plugged 10,000 times
The first to publish is credited on this line, and the deliverable moves from Open to Achieved.
What to build
An open rig that plugs a USB-C cable into a phone's charging port up to 10,000 times, the life that makers such as GCT rate their bare connectors for, and every 500 cycles checks that the phone still charges, the voltage lost across the plug at a fixed current, and the force needed to pull the plug out. Run it on several phone models, with straight insertions from a motion stage and angled, off-center ones like people make from a small robot arm.
Why it is still open
Connector datasheets rate the bare part: GCT's USB4081 receptacle, for example, is specified for 10,000 cycles at 500 per hour under the EIA-364-09 test, with a pull-out force of 6 to 20 N after cycling and a maximum contact resistance. A search for cycle tests of the ports in finished phones, where the case, the board and the angle of use all matter, found only such part datasheets.
Built with what exists
A linear actuator or an old 3D printer's motion stage for straight insertions; an SO-101 arm run with Hugging Face's open LeRobot software for angled ones (see the Note "No download", on LeRobot v0.7.0); a USB-C power meter logging voltage and current at 5 V; a digital force gauge; used phones from refurbishers; Python.
First step
Build the straight-insertion rig and run 1,000 cycles on one used phone, logging voltage drop every 100 cycles.
Done looks like
10 phone models, three units each, run to 10,000 cycles or to the first charging fault, with cycles to fault, pull-out force before and after, and voltage drop at 2 A every 500 cycles published, along with video and drawings of the rig.