Industries / Industrial equipment and services / Industrial machinery
Compressors
The compressor industry designs and builds the machines that raise the pressure of air and other gases, from small workshop units to the machines that feed chemical plants, pipelines and hydrogen stations.
1776
A steam engine from Boulton & Watt, by Samuel Smiles's account the first the firm made at Soho, began blowing air into John Wilkinson's iron furnace at Broseley, England.
34
Milestones achieved across 6 domains.
9
To watch for: announced, not yet confirmed outside.
12
Open deliverables. Nobody has shipped them.
In one minute
Where it started
For more than a century compressors were piston machines, blowing air into iron furnaces and, from 1889, feeding a network of air pipes under Paris. Machines that spin came next: Brown Boveri built a turbo-compressor with 25 impellers in 1906, and the screw compressor of Alf Lysholm, an engineer in Stockholm, was patented in 1935.
Where it stands
Oil-injected screw machines make most factory air; by the late 1990s screws were 80% of the displacement compressors sold, wrote N. Stosic of City University, London. Centrifugal machines, most new ones sealed with dry gas seals, serve pipelines and process plants, and piston machines still reach the highest pressures, up to 3,500 bar for polyethylene by Burckhardt Compression's figures. The United States has required a minimum efficiency for lubricated rotary air compressors of 10 to 200 hp since January 2025, China has graded its compressors since 2009, and the European Union drafted a rule twice without adopting it.
What is open
Much of what the trade knows sits in makers' records or in rules of thumb: no public table pools leak losses across plants, checks certified ratings against makers' data sheets, or collects the published cases of rotor whirl and gas seal failure. The open jobs are mostly data and small test rigs, from measuring what shop compressors really deliver to sharing plant logs on which compressor controllers can be compared. Hydrogen is where new machines are being tried, and in NREL's 2016 data compressors failed more often than any other part of US hydrogen stations.
Domains
AchievedWatch forOpen
Domain
Progress
Last achieved
Watch for
Open
Piston compressors
A piston moving in a cylinder draws gas in through one valve and pushes it out through another at higher pressure; these machines reach the highest pressures of any compressor.
6 · 2 · 2
Last achievedStation compressors fail most2016
Watch forLiquid in place of pistons
2
openScrew compressors
Two meshing rotors with spiral lobes trap gas and squeeze it as it moves along them; this is the usual machine for factory air.
6 · 2 · 2
Last achievedOil-free air, certified2006
Watch forWater-cooled single screw
2
openCentrifugal compressors
Designing, building and testing machines that raise gas pressure by flinging the gas outward from spinning impellers (centrifugal) or pushing it along the shaft through rows of blades (axial).
5 · 1 · 2
Last achievedStability checks enter the standard2002
Watch forCarbon-fiber impellers for hydrogen
2
openSeals and bearings
Making the parts that hold a compressor's spinning shaft in place and keep the gas inside where the shaft leaves the casing.
6 · 1 · 2
Last achievedA standard for gas seals2018
Watch forSeparation seals that save nitrogen
2
openControls
Matching a compressor's output to what the plant is using, and keeping the machine out of conditions that damage it.
4 · 3 · 2
Last achievedNetworks tied to one brand2016
Watch forDemand matching for fixed speed
2
openEfficiency and service
Measuring how much power a compressor uses for the air it delivers, setting minimum standards, auditing whole air systems and keeping machines serviced.
7 · 0 · 2
Last achievedA first US efficiency floor2025
2
open
Advances to build with
1 research note
Open in compressors
3 of 12 open deliverables
Open · Piston compressors
Check shop compressor labels
A measured table of the air that 20 common small piston compressors, sold for homes and workshops, actually deliver at 90 psi (6.2 bar), with the power each draws, set against the figures printed on their labels and boxes.
Built with what exists
A thermal mass flow meter made for compressed air, a pressure regulator and needle valve after the tank outlet, a plug-in power meter, a thermometer, and a laptop to log readings. Each unit runs as sold, at its own rated pressure.
Open · Screw compressors
Measured screw rotor profiles
A public library of 3D scans of rotor pairs from 20 retired screw airends (the rotor and housing unit) of different makes and sizes, bought by the team for research, with the cross-section profile extracted and the main design numbers computed by open code: lobe counts, rotor diameters, center distance, wrap angle, volume per turn, length of the sealing line and size of the leak gap at the lobe tips.
Built with what exists
Retired airends from rebuild shops; a structured-light 3D scanner or a university's coordinate measuring machine; open mesh and CAD tools such as Open3D and FreeCAD; Python for the profile math.
Open · Centrifugal compressors
A public whirl case table
One open table of every published case of subsynchronous whirl in a centrifugal compressor, with the machine's data (stages, speed, first critical speed, discharge pressure, gas density, bearing and seal types), whether it was unstable, and what fixed it. Then a test of how many unstable cases the API 617 Level I screen, as Nicholas and Kocur describe it, would have flagged.
Built with what exists
Texas A&M Turbomachinery Symposium proceedings (open access in its OAKTrust repository, and searchable through CORE's free API at api.core.ac.uk); NASA's rotordynamic instability workshop papers on ntrs.nasa.gov; a small AI model built for extraction from long documents, such as Meta's Muse Ember (see the Note "The jobs agents repeat"); a spreadsheet.
Where it sits
Broader
Industrial machinery
