BRENNEN

Industries / Transport and vehicles / Automotive / Collision repair

Paint

Refinishing is the repainting of repaired or replaced panels so they match the rest of the car, done by a painter in a spray booth.

5

Milestones achieved, from 1926 to 2013.

1

To watch for: announced, not yet confirmed outside.

2

Open deliverables. Nobody has shipped them.

The road

AchievedWatch forOpen

Achieved

  1. 1926

    Paint goes on by gun

    Repair shops once brushed paint on. By the mid-1920s DeVilbiss, Binks and Iwata sold spray guns, and the new nitrocellulose lacquers dried too fast to brush, so they had to be sprayed; Gary Ledoux's history of the trade dates the first spraying in shops to 1926. The overspray "went everywhere – including into the lungs of the refinisher," and painters first pulled it out with exhaust hoods borrowed from restaurant kitchens, set over crude booths.

    LessonA faster way to put paint on also put paint mist into the painter's lungs, so ventilation had to follow.

    fenderbender.comfenderbender.com

    Credit

    DeVilbiss, Binks and Iwata, the spray gun makers, by Ledoux's account

  2. 1980s

    Downdraft booths take over

    In a downdraft booth, filtered air comes in through the ceiling and leaves through the floor, carrying overspray down and away from the car. Ledoux writes that the downdraft booth "began to really catch traction" in the early 1980s, when clearcoats (a clear top layer over the color) made a dirt-free finish worth paying for, since every speck had to be buffed out by hand. In demonstrations with models, the UK Health and Safety Executive (HSE) showed that painters' exposure in a simple spray room runs to thousands of micrograms per cubic meter of air, against hundreds in a booth.

    fenderbender.comhse.gov.uk

    Credit

    booth makers, not named in the source; HSE for the exposure comparison

  3. 2008

    US rules for shop spraying

    On 9 January 2008 the US Environmental Protection Agency (EPA) published national rules for paint stripping and surface coating at small sources, known as the 6H rule (40 CFR part 63, subpart HHHHHH). EPA estimated that about 35,000 of the covered businesses refinish vehicles, employing about 263,000 people, a third of them painters. Every painter must be trained and certified, existing shops by 10 January 2011; all spraying must be done in a booth or enclosure whose filters catch at least 98% of overspray; guns must be HVLP (high-volume, low-pressure, which puts more paint on the panel and less in the air) or equivalent; and guns must be cleaned without spraying solvent into the air.

    govinfo.govlaw.cornell.edu

    Credit

    US EPA

  4. 2009

    Water-based color coats required

    Solvents that evaporate from paint, counted as volatile organic compounds (VOCs), help form smog. On 20 October 2005 the California Air Resources Board (CARB) approved a model rule for its air districts that limited color coats to 420 grams of VOC per liter from 1 January 2009. Its staff expected makers to meet the limit with water-based color coats, which by CARB's account had been used in Europe for about ten years and were required there from 1 January 2007, and estimated a cut of 13.4 tons of VOC a day statewide, about 63% of emissions from these coatings. Canada set the same 420 g/L limit for color coats in national regulations registered in June 2009, in force a year later. In November 2024 the South Coast district, which covers the Los Angeles area, set its next limit: 250 g/L for color coats from 1 January 2030.

    LessonCARB staff warned that drying water instead of solvent would need more air movement in the booth, and perhaps heat, to keep shops' output up.

    otcair.orgww2.arb.ca.govlaws-lois.justice.gc.caaqmd.gov

    Credit

    CARB; Environment Canada; South Coast AQMD

  5. 2013

    Isocyanate exposure targeted

    Two-pack refinish paints harden through isocyanates, chemicals that can cause occupational asthma. In the UK, HSE says vehicle paint sprayers have "for years" been the group most at risk of it, and that the only accepted way to check a sprayer's exposure is a urine test, judged against a guidance value of 1 µmol of isocyanate breakdown products per mol of creatinine. In the US, the Occupational Safety and Health Administration (OSHA) began a National Emphasis Program on isocyanates on 20 June 2013, a program of targeted inspections that names auto body repair among the uses and lists body, paint and interior repair shops among the industries to visit.

    LessonWhen HSE tested everyone in one large bodyshop after complaints, all of them were exposed, and the most exposed person was the receptionist.

    hse.gov.ukhse.gov.ukosha.gov

    Credit

    HSE; OSHA

Watch for

  1. Robots paint repaired cars

    ONEW Technology, a Chinese firm, says its PaintGo robot, installed in February 2026 at Fix Auto Dorval in Quebec and two other Canadian shops, uses about 12% less paint than the best human painter. The shop said it was "hard to say" whether the robot is faster and that it had noticed consistent results. SATA, the spray gun maker, has formed SATA Automation to sell CurveRobot's painting robot, which it says is in daily use at a repair shop in Hanover, Germany, and the robot maker NST says several Asia-Pacific body shops use its robots daily with Surventis paints.

    Achieved whena shop or an outside party publishes paint used, film thickness, color match and redo rates for many robot-painted and hand-painted repairs of the same kind.

    autosphere.cacollisionweek.comcollisionweek.com

    Claimed by

    ONEW Technology, June 2026; SATA and NST, 2026

Open

  1. 01

    Booth clearance times, measured

    A public table of measured clearance times, the time after spraying stops until a booth's air is clear of paint mist, for at least 30 spray booths and spray rooms, set against the time each shop has posted on its door. The test uses theatrical fog, not paint.

    The brief
    Credit · unclaimed
  2. 02

    Robot or painter, measured

    A side-by-side record from a shop that has a refinish robot: paint weighed per panel, film thickness, color difference from the next panel and the share of jobs redone, for robot-painted and hand-painted repairs of the same kind.

    The brief
    Credit · unclaimed

Open 01 · the brief

Booth clearance times, measured

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

A public table of measured clearance times, the time after spraying stops until a booth's air is clear of paint mist, for at least 30 spray booths and spray rooms, set against the time each shop has posted on its door. The test uses theatrical fog, not paint.

Why it is still open

HSE tells shops to measure clearance time with a smoke or fog generator and mark it on the booth door, and in September 2025 its campaign published a blank certificate for posting the result. Its own model demonstration showed a spray room clearing far more slowly than a booth. HSE's research reports on clearance (RR496, RR742) have moved to the UK National Archives and could not be opened, and no public record of measured times across many shops was found.

hse.gov.ukworkright.campaign.gov.ukhse.gov.uk

Built with what exists

a glycol fog machine of the kind sold for stage effects; a low-cost laser particle sensor such as the Plantower PMS5003, checked against a calibrated optical particle counter, logging to a Raspberry Pi; a phone video of each run; HSE's certificate template.

  1. First step

    Fog-test one booth at a willing shop three times, with the extraction running and no one inside, and compare the result with the time on its door.

  2. Done looks like

    At least 30 booths or rooms in at least 10 shops, each tested three times with the booth empty of paint, giving the time to return to background particle counts, the spread between runs and the gap from the posted time, with the data and method public.

Open 02 · the brief

Robot or painter, measured

Credit · unclaimed

The first to publish is credited on this line, and the deliverable moves from Open to Achieved.

What to build

A side-by-side record from a shop that has a refinish robot: paint weighed per panel, film thickness, color difference from the next panel and the share of jobs redone, for robot-painted and hand-painted repairs of the same kind.

Why it is still open

The 12% paint saving for PaintGo is the maker's own figure, and the shop could not yet say whether the robot is faster. SATA and NST say their robots are in daily use but give no counts. No published comparison from a working shop was found.

autosphere.cacollisionweek.com

Built with what exists

the shop's paint-mixing scale, which logs grams per mix; a coating thickness gauge; a multi-angle spectrophotometer of the kind used for color matching (ASTM E2194); colour-science, an open-source Python library, for CIEDE2000 color differences; the shop's repair orders.

  1. First step

    Ask one of the shops named in trade coverage, such as Fix Auto Dorval, for a month of mixing-scale logs split between robot and hand jobs.

  2. Done looks like

    At least 100 repairs, about half by robot and half by hand, giving grams of paint per square meter, the mean and spread of film thickness, the color difference at the panel edge and the share redone, with the method published so another shop can repeat it.