Industries / Industrial equipment and services / Industrial machinery
Boilers and pressure vessels
The boiler and pressure vessel industry designs, builds and certifies the steel shells that hold steam, gas or liquid under pressure, from heating boilers and air receivers to power station boilers, refinery reactors and nuclear reactor vessels, and keeps them safe through inspection and repair once they are in service.
1915
In spring 1915 the American Society of Mechanical Engineers (ASME) issued its first boiler rules, "Rules for the Construction of Stationary Boilers", dated 1914, written by a committee formed in September 1911. ASME credits its president, Col. Edward D. Meier, with proposing the code in 1911, and names John A. Stevens, a former member of the Massachusetts Board of Boiler Rules, as the committee's chair.
27
Milestones achieved across 5 domains.
7
To watch for: announced, not yet confirmed outside.
11
Open deliverables. Nobody has shipped them.
In one minute
Where it started
Steam boilers exploded often in the 1800s. Hartford Steam Boiler, founded in 1866 to inspect and insure boilers, says that in the 1850s US explosions came "almost one every four days". The steamboat Sultana blew up on the Mississippi in 1865, killing 1,195 people by the American Battlefield Trust's count, and in 1905 a boiler explosion at the Grover shoe factory in Brockton, Massachusetts killed 58. Massachusetts wrote boiler rules, and ASME's code of 1915 turned such rules into one book that states could adopt as law.
Where it stands
ASME's first code was one book of 114 pages; ASME says the 2001 edition ran to more than 16,000 pages, the code now fills 28 books, and all Canadian provinces and 49 of the 50 US states have adopted parts of it into law. Europe works to its Pressure Equipment Directive and the EN 13445 standard, and China to its TSG 21 safety rules and the GB/T 150 standard. Welding replaced rivets, heavier forging presses cut the number of welds in the largest vessels, and electron beam welding has cut some thick-wall weld times from days to minutes in nuclear trials.
What is open
Much of the checking is still done by hand and in private: code calculations, heat-treatment charts, the fracture surfaces of toughness tests and the thickness maps of corroded tubes. The National Board stopped publishing its yearly incident report in 2005, and there is no open, coded record of boiler accidents in its place. Open test sets, shared test suites for calculators and labeled data from tests and inspections are within reach of a small team, and AI models that read long documents and do arithmetic make several of these jobs faster to attempt.
Domains
AchievedWatch forOpen
Domain
Progress
Last achieved
Watch for
Open
Design and codes
This work sets and applies the rules that fix how a boiler or vessel is laid out, how thick its walls must be, which steels may be used and how much safety margin is left, before any plate is cut.
6 · 1 · 2
Last achievedMargin cut from 4 to 3.51999
Watch forAn AI model for ASME codes
2
openForming and welding
This work turns steel plate and ingots into shells, heads and rings, by rolling, pressing and forging, and joins them with welds as strong as the plate.
4 · 2 · 2
Last achievedA vessel welded in minutes2025
Watch forElectron beam welding in a US shop
2
openTesting before shipping
This work proves a finished vessel before it leaves the shop: testing the toughness of its steel, filling it with water above its working pressure and having an independent inspector witness the result and stamp the vessel.
5 · 0 · 2
Last achievedTest with water, not gas2012
2
openBurners and controls
This work fires a boiler and keeps it safe while it runs: the burner that mixes fuel and air, the flame detector that shuts the fuel off if the flame goes out, and the controls that stop the burner when the water runs low.
5 · 2 · 3
Last achievedZero emissions for small boilers2026
Watch forA burner for any hydrogen share
3
openInspection and repair in service
This work checks boilers and vessels at intervals once they are running, judges whether damage found can be left in service, and repairs them under rules that keep the repair as sound as the original.
7 · 2 · 2
Last achievedA repair that left thin steel2017
Watch forAI estimate of boiler damage
2
open
Open in boilers and pressure vessels
3 of 11 open deliverables
Open · Design and codes
Code calculations, tested in public
An open, machine-readable set of pressure vessel design problems: shell and head thickness, nozzle reinforcement and flat covers, each with its inputs, the clause it follows, the expected answer and a tolerance. Use it to score AI models and calculation software against the same answers.
Built with what exists
Python with the pint library for units; JSON Schema for the case format; open calculators such as calctoys and ASME-PVDE as reference answers; allowable stresses supplied as inputs so that no copyrighted tables are copied; AI models called through their public interfaces (the Note "Seven more flagged" covers an AI reviewer of long documents).
Open · Forming and welding
Heat-treatment charts read by machine
A program that reads the thermocouple records of post-weld heat treatment, the slow heating and holding that relieves stress in a finished weld, from logger files or scanned paper charts, and flags any hold that ran too cool, too short, or heated or cooled too fast against a rule table the user sets.
Built with what exists
Python with pandas; WebPlotDigitizer or an AI vision model to read paper charts, every reading checked by hand; a rule table in YAML that can be edited.
Open · Testing before shipping
Toughness fractures graded by camera
An open set of photographs of broken Charpy specimens, each labeled with its percent shear (the share of the broken face that tore in a ductile way) by experts, and a model that measures percent shear from a photograph.
Built with what exists
Broken specimens from a university or test laboratory, used with permission; a camera on a copy stand with fixed lighting; CVAT for outlining; a segmentation model such as a U-Net trained on one graphics card.
Where it sits
Broader
Industrial machinery